Town & Country Fireplaces TC36 Gebrauchsanweisung

160617-125056.9036-A_TC36D

Dimensions | Clearances | Venting

IMPORTANT

This booklet is intended as a basic speciﬁcation

guide for architects, designers and builders.

Please refer to the Instruction Manual supplied

with the ﬁreplace for detailed information regarding

installation and operation.

Product installation manuals can also be viewed at:

www.townandcountryﬁreplaces.com

FOR ARCHITECTS & DESIGNERS

TC36

SERIES D

For reFerence only. consult Manual beFore installation

160617-12 5056.9036-A_TC36D

47 3/4"

32 1/2"

3 5/8"

38 1/2"

36 1/8"

32 1/2"

26 9/16"

38 1/2"

47 3/8"

26 1/16"

26 9/16

Fireplace Dimensions

Examples of Common Locations

FRAMING

LINTEL

Must allow for minimum 1/2 inch

gap for drywall/sheetrock and

facing

TC36D Cad Drawing

Available at

www.townandcountryreplaces.com

See minimum combustible framing dimensions

section on page 4 for precise framing dimensions

For reFerence only. consult Manual beFore installation

160617-125056.9036-A_TC36D

Mantel Clearance Chart

Minimum Clearances to Combustibles

* MANTEL CLEARANCE

A 9”

B 6”

C 3”

MANTEL CLEARANCE

CHART

** MANTEL DEPTH

D 12”

E 6 3/4”

F 1 1/2”

MAY USE COMBUSTIBLE

FACING MATERIAL IN THIS AREA

NON-COMBUSTBLE

FINISH MATERIAL

NON-COMBUSTIBLE ZONE.

DO NOT INSTALL ANY COMBUSTIBLE MATERIAL,

ELECTRICAL WIRING OR GAS PLUMBING IN THIS

AREA.

COMBUSTIBLE FRAMING AND

FINISH WALL ABOVE STANDOFFS

STANDOFFS

STEEL FRAMING

FIREPLACE FRONT

TOP OF LINTEL BAR

24"

38 1/8"

Minimum Clearances:

Side standoffs ............................................. 0 in. (0 mm)

Back standoffs ............................................ 0 in. (0 mm)

Top standoffs............................................... 0 in. (0 mm)

Bottom of appliance .................................... 0 in. (0 mm)

Adjacent side wall........................................ 4 in. (102 mm)

Ceiling to appliance ................................... 24 in. (610 mm)

*Mantel to appliance......................See Figure #4

**Maximum Mantel extension.........See Figure #4

Mantel support ............................................ 4 in. (102 mm)

Vertical vent pipe ................................. 1 3/4" in. (45 mm)

Horizontal Vent pipe (Top, sides and bottom)1 3/4" in. (45 mm)

MANTEL

Adjacent wall or mantel

support

CEILING

Unit may be recessed up to 4 1/2” with

non-combustible masonary type material

For reFerence only. consult Manual beFore installation

160617-12 5056.9036-A_TC36D

20 7/8"

50 1/4"

29 1/2"

61 1/16"

62 5/8"

Minimum

86 5/16"

12 3/8"

FRAMING

LINTEL

50 1/4"

23 7/8"

25 7/8”

50 1/4"

48 1/16"

Steel Stud Framing Kit Dimensions Kit

Minimum Combustible Framing Dimensions

NON-COMBUSTIBLE materials must

extend 12” above and 5 5/8” to the

sides of the framing edges.

NON-COMBUSTIBLE BOARD NOT

INCLUDED.

NON-COMBUSTIBLE

BOARD

All other framing can be done with

conventional lumber

NOTE: Fireplace should be in its final location before framing.

Non-combustible

Board Detail

12”

5 5/8”

Framing kit is supplied

with unit with Fireplace

Must allow for

minimum 1/2 inch

gap for

drywall/sheetrock

and facing

For reFerence only. consult Manual beFore installation

160617-125056.9036-A_TC36D

Proflame 2 Control System

Hearth Extension

Side Facing Clearances

Up to 40 Feet

Caution: While a hearth extension is not required and

combustible ﬂooring materials may be brought directly up

to the ﬁreplace, many materials (such as wood ﬂooring)

may not tolerate the radiant heat from this ﬁreplace,

resulting in discoloration, shrinking and cracking. For this

reason, we suggest a non-combustible hearth that is no

more than 1” above the bottom of the ﬁreplace. If material

is thicker, ﬁreplace must be raised accordingly.

Caution: Hearth extensions thicker than 1” will

interfere with the window frame when opening.

REMOTE

OFF

PROGRAM

TOWN & COUNTRY

LUXURY FIREPLACES

Town and Country D Series ﬁreplaces use the SIT

Proﬂame 2 control system.

This includes an elegant hand-held, programmable,

multi-function remote control transmitter with an easy

to read LCD display.

The ﬁreplace also comes with a Town & Countrys’

proprietary wall-mounted control panel which allows

for simple ON/OFF operation, or can be linked with

the hand-held remote control unit. This panel also

accepts four double A batteries to provide for a back-

up system during power outages. The wall-mounted

panel also works on most customer supplied Home

Automation Systems which allow for full control of

ﬁreplace ﬂame and light modulation.

SUB FLOOR

LINTEL

Surface of hearth extension

may not be higher than the

oor of the lintel and may not

be more than 1 inch above

the bottom of the replace.

Caution: This ﬁreplace may be recessed up to a

maximum depth of 4 1/2”. This recess must be

constructed from non-combustible material. The space

between the outside framing edge and the ﬁrebox must

be completely free of any obstructions or debris, and the

window, with trim ﬁtted, must be able to move freely.

No building material is permitted to protrude past the

framing edges attached to the replace under ANY

circumstance.

For reFerence only. consult Manual beFore installation

160617-12 5056.9036-A_TC36D

Direct Vent Wall Installation

* Minimum height from the oor to center of the

opening with a maximum horizontal run of 20 1/2”

from the center of the ue outlet to the outside face of

the outer wall. The height will need to be increased if a

longer horizontal pipe is required.

Direct Vent

Roof Installation

* 68 1/2

HORIZONTAL

TERMINAL

TCVT.9360

14 1/2" FRAMED

OPENING

WALL SHIELD THIMBLE

TCVT.THIMA

ELBOW

TCVT.811XLB90

MIN 24" VENT PIPE

TCVT.811X24

12" VENT

PIPE MIN.

TCVT.811X12

For reFerence only. consult Manual beFore installation

160617-125056.9036-A_TC36D

Wall Termination Venting Chart

NOTE: The vent must not exceed a total length of 68 feet. Any

combination of rise and run may be used but must be constrained

to the boundaries of this chart. A total of 3 - 90° elbows or

combination of other elbows equalling 90° can be used without

reducing horizontal run. For each additional 90° elbow, or an

equal combination of elbows, reduce horizontal vent run by 2

feet. Ensure vent pipe is properly supported.

** All dimensions are approximate. Both rise and run may vary with different

combinations of pipe.

Minimum rise

Pipe length

Maximum run

Pipe length

Max.

68 1/2” 1-24” 20 1/2" 1-12"

72 3/4” 1-12” 1-18" 75 3/4" 1-48" 1-12"

78 3/4” 1-24" 1-12” 11' 2" 2-48" 1-24"

84 3/4” 1-24” 1-18" 15' 10 1/2" 3-48" 1-24"

1-12"

92 1/2” 1-48” 20’ 10 1/2” 5-48"

For other rise/run combinations see chart below

TC36D Cad Drawing

Available at

www.townandcountryreplaces.com

For reFerence only. consult Manual beFore installation

160617-12 5056.9036-A_TC36D

Roof Termination Venting Chart

24" Pipe

length

minimum

NOTE: The vent must not exceed a total length of 68 feet. Any

combination of rise and run may be used but must be constrained

to the boundaries of this chart. A total of 4 - 90° elbows or

combination of other elbows equalling 90° can be used without

reducing horizontal run. For each additional 90° elbow, or an

equal combination of elbows, reduce horizontal vent run by 2

feet. Ensure vent pipe is properly supported.

** All dimensions are approximate. Both rise and run may vary with different

combinations of pipe.

Minimum rise

Pipe length

Maximum run

Pipe length

Maximum

68 1/2” 1-24” 29" 1-12"

72 3/4” 1-12” 1-18" 75 1/4" 1-48" 1-12"

78 3/4” 1-24" 1-12” 11' 1 1/2" 2-48" 1-24"

84 3/4” 1-24" 1-18" 15' 10" 3-48" 1-24"

1-12"

92 1/2” 1-48” 20’ 10” 5-48"

For other rise/run combinations see chart below

TC36D Cad Drawing

Available at

www.townandcountryreplaces.com

For reFerence only. consult Manual beFore installation

160617-125056.9036-A_TC36D

Vent Terminal Clearance

Vent Terminal Minimum Clearances

Minimum clearances to the vent terminal must be maintained as

shown (See illustration to right & below). Measure clearances to

the nearest edge of termination hood. (See pitch table below).

NOTE: Vent terminal must not be recessed

NOTE: LOCAL CODES OR REGULATIONS MAY REQUIRE

DIFFERENT CLEARANCES.

Terminal to sloped Roof Pitch Table

(minimum)

ft m

Flat to 6/12 1.00 0.30

Over 6/12 to 7/12 1.25 0.38

Over 7/12 to 8/12 1.50 0.46

Over 8/12 to 9/12 2.00 0.61

Over 9/12 to 10/12 2.50 0.76

Over 10/12 to 11/12 3.25 0.99

Over 11/12 to 12/12 4.00 1.22

VENT TERMINAL MINIMUM CLEARANCES

TO ADJACENT STRUCTURES

A= *12 inches (30 cm) min. Clearances above grade, veranda, porch, deck, or balcony

B= *12 inches (30 cm) min. Clearance to window or door that may be opened

C= 12 inches (30 cm) min. Clearance to permanently closed window recommended to prevent condensation on window

D= 30 inches (76 cm) min. Vertical clearance to ventilated sofﬁt located above the terminal within a horizontal distance of 2 feet (60 cm) from the

edge of the terminal

E= 30 inches (76 cm) min. Clearance to unventilated sofﬁt

F= 6 inches (15 cm) min. Clearance to outside corner

G= 6 inches (15 cm) min. Clearance to inside corner

H= 3 feet (90 cm) min. *Not to be installed above a meter/regulator assembly within 3 feet (90 cm) horizontally from the center-line of the

regulator

I= *6 feet (1.8 m) min. Clearance to service regulator vent outlet

J= *12 inches (30 cm) min. Clearance to non mechanical air supply inlet to building or the combustion air inlet to any other appliance

K= *6 feet (1.8 m) min. Clearance to a mechanical air supply inlet

L= *7 feet (2.1 m) min. ^ Clearance above paved side-walk or a paved driveway located on public property

M= **30 inches (76 cm) min Clearance under veranda, porch, deck, or balcony

^ a vent shall not terminate directly above a side-walk or paved driveway which is located between two single family dwellings and serves both dwellings*

** only permitted if veranda, porch, deck, or balcony is fully open on a minimum of 2 sides beneath the ﬂoor*

* as speciﬁed in CAN/CSA B149.1 Installation Codes, Note: local Codes or Regulation may require different clearances

* for U.S.A. Installations follow the current National Fuel Gas Code, NFPA54/ANSI Z223.1

AIR SUPPLY INLET

VENT TERMINAL GAS METER

AREA WHERE TERMINAL

IS NOT PERMITTED

FIXED

CLOSED

FIXED

CLOSED OPEN-

ABLE

OPEN-

ABLE

36"

See Roof

pitch table

48"

ADJACENT

24"

(91.5 cm)

(61 cm)

(122 cm)

STRUCTURES

OR FENCE

For reFerence only. consult Manual beFore installation

160617-12 5056.9036-A_TC36D

Up to 66 feet

of vertical run

Up to 110 feet of run

plus six 90º elbows

Up to 3 feet below unit

Optional Power Vent

Power Vent Terminals

Direct Vent Terminals

Reach almost any room or commercial setting.

Optional Power Venting allows runs up to

110’ from an outside wall or roof surface. Vent

horizontally or vertically with up to six 90-degree

elbows, including runs up to 3’ below the

ﬁreplace.

The premium Power Vent fan runs quietly outside,

at the exterior terminal.

Roof Termination

Flush Mount termination

Stainless Steel Standard Venting

Termination for Condo Installation

Standard Venting

Wall Termination

Standard Venting

Roof Termination

TC36D Cad Drawing

Available at

www.townandcountryreplaces.com

Andere Handbücher für TC36

Inhaltsverzeichnis

Andere Town & Country Fireplaces Kamin im Innenbereich Handbücher

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces Architectural Series Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54NG04.C2 Technisches Handbuch

Town & Country Fireplaces

Town & Country Fireplaces TC42 Einrichtungshandbuch

Town & Country Fireplaces

Town & Country Fireplaces TCW120 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54CODE Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.CSTE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30.NG04D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54STOK Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54CSTE Betriebsanleitung

Town & Country Fireplaces

Town & Country Fireplaces T120.RHKIT Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces Model TC42SeriesC Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36ST Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30 Black Diamond Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54DST Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCW120 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch