Town & Country Fireplaces Architectural Series Bedienungsanleitung

INSTALLATION MANUAL

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

This appliance may be installed in an aftermarket

permanently located, manufactured home (USA only)

or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of

gas indicated on the rating plate. This appliance

is not convertible for use with other gases,

unless a certiﬁed kit is used.

FOR YOUR SAFETY

Installation and service must be performed by

a qualiﬁed installer, service agency or the gas

supplier.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier call

the ﬁre department.

Do not store or use gasoline or other

ﬂammable vapors and liquids in the vicinity of

this or any other appliance.

WARNING: If the information in these instructions is

not followed exactly, a ﬁre or explosion may result

causing property damage, personal injury or death.

This appliance is suitable for installation in a

bedroom or bed sitting room.

This is a decorative product and is not intended

to be used as a heating appliance.

PENINSULA

INSTALLATION

MANUAL

Architectural Series 100000847-50160819-52

Table of Contents

Caution ................................................................................. 3

Safety ................................................................................... 3

Important Note for the Commonwealth of Massachusetts .. 4

Congratulations on your Town & Country purchase ............. 5

Installation Requirements/Appliance Specications ............ 5

Installation Requirements ..................................................... 6

Vent Terminal Minimum Clearances ..................................... 6

Minimum Clearances to Combustible Material .................... 6

Appliance Dimensions ...........................................................7

Peninsula Dimensions using 16 inch High Glass..............7

Peninsula Dimensions using 24 inch High Glass............. 8

Btu Values and Weights ........................................................ 9

Minimum Clearances to Combustible Material .................... 9

Locating the Unit ................................................................ 10

Upper Support for Light Framed Units ................................11

Removing Vertical Supports ............................................... 12

Framing and Finishing ........................................................ 13

Framing.......................................................................... 14

Facing Material .............................................................. 15

Venting Conguration ......................................................... 16

Venting plenum .............................................................. 16

NOTE: Plenum must not be shared with

other appliances. .......................................................... 16

Venting Specications .........................................................17

Air Intake ............................................................................ 18

Optional Motorized Damper ............................................... 19

Power Vent ......................................................................... 20

Power Vent Dimensions ......................................................21

Vertical Installation ..............................................................21

Horizontal Installation ......................................................... 22

Vent Terminal Clearance ..................................................... 23

Power Vent Wiring .............................................................. 24

Flush Mount Power Vent Details ........................................ 25

Flush Mount Power Vent Dimensions ................................ 25

Mounting the Flush Mount Power Vent .............................. 26

Removing the grill .......................................................... 26

Installing the fan unit...................................................... 26

Minimum Clearances to Combustibles .............................. 26

Framing the Flush Mount Power Vent .................................27

Flush Mount Electrical Connection .................................... 28

Bafe Adjustment ............................................................... 29

Glass Burner Tray and Media Installation ........................... 30

Burner tray installation................................................... 30

Applying glass media......................................................31

Window Frame Installation/Removal .................................. 32

LED Strip Replacement ...................................................... 34

Removing an LED section ............................................. 34

Electrical Connection ......................................................... 36

Electrical Diagram ...............................................................37

Control Panel Installation ................................................... 38

Installation instructions.................................................. 38

Gas Connection .................................................................. 43

Gas Pressure Requirements ............................................... 43

Lighting Instructions ........................................................... 44

Maintenance ....................................................................... 45

GLASS PANEL: .............................................................. 45

ANNUAL INSPECTION: ................................................. 45

Periodically: .................................................................. 45

Rating Labels ...................................................................... 46

2100000847 160819-52Architectural Series

Caution

We recommend that our gas hearth

products be installed and serviced

by professionals who are certiﬁed

in the United States by the National

Fireplace Institute®(NFI) as NFI Gas

Specialists

This appliance and its individual shut off valve must be disconnected from gas supply piping system

during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).

This appliance must be isolated from the gas supply piping system by closing its individual manual

shut off valve during any pressure testing of the gas supply piping system at test pressures equal to or

less than 1/2 psig (3.5 kPa).

Do not use the ﬁre feature if any part has been under water. Immediately call a qualiﬁed service techni-

cian to inspect the ﬁre feature and to replace any part of the control system and any gas control which

has been under water.

Power supply to the ﬁreplace must be shut off before connecting or disconnecting the CAT5e cable to

the touch screen/toggle switch wall receptacle. This also applies to the touch screen charging cable.

Safety

Any grill, panel or door removed for servicing the unit must be replaced prior to operating. Failure to do so

may create a hazardous condition.

Installation and repair should be done by a qualied service person. The appliance should be inspected

before use and at least annually by a professional service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments,

burners and circulating air passageways of the appliance be kept clean.

It is our policy that no responsibility is assumed by the Company or by any of its employees or

representatives for any damages caused by an inoperable, inadequate, or unsafe condition which is the result,

either directly or indirectly, of any improper operation or installation procedures.

This appliance must not be connected to a chimney ue serving a separate solid fuel burning appliance.

3Architectural Series

160819-52 100000847

Important Note for the Commonwealth of Massachusetts

From Massachusetts Rules and Regulations 248 CMR 5.08:

(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential

purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet

above nished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satised.

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the

installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the oor

level where the gas equipment is to be installed, in addition, the installing plumber or gas tter shall observe that a battery operated or hard-wired

carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal

vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualied licensed professionals for the

installation of hard-wired carbon monoxide detectors.

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard-wired carbon monoxide

detector with alarm and battery back-up may be installed on the next adjacent oor level.

b. In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall have a period of thirty

(30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide

detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall

comply with NFPA 720 and be ANSI/UL 2034 listed as IAS certied.

3. SIGNAGE. A metal or plastic identication plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet

above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall

read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless,

upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.089(2)

(a) 1 through 4.

(b) EXEMPTIONS. The following equipment is exempt from 248 CMR 5.089(2)(a) 1 through 4.

1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the

Board; and

2. Product Approved side wall horizontal vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure

used in whole or in part for residential purposes.

(c) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side wall

horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided

by the manufacturer for installation of the equipment and the venting system shall include:

1. Detailed instructions for the installation of the venting system design or the venting system components; and

2. A complete parts list for the venting system design or venting system.

(d) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved

side wall horizontally vented gas fueled equipment does not provide the parts for venting the fuel gases, but identies “special venting systems”, the

following requirements shall be satised by the manufacturer.

1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed

installation instructions.

(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts

lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

4100000847 160819-52Architectural Series

Your Architectural Series Zero Clearance linear appliance has been professionally installed by:

Dealer name: _____________________________________________

Phone Number: ___________________________________________

If you discover any problems with your linear appliance, contact your dealer immediately to have the unit

repaired.

Caution: Do not attempt to repair the linear appliance because you may cause injury to yourself or others,

and risk causing damage to the unit.

Before operating your linear appliance carefully read this manual and pay close attention to all Safety

Warnings. The manual contains important information on the unit’s safe operation and maintenance.

Installation Requirements/Appliance Speciﬁcations

Town and Country Architectural Series linear appliance.

Speciﬁcations

Congratulations on your Town & Country purchase

• This unit has been tested to ANSI Z21.50 and CSA P.4.1 specications.

• Single wall (min. 26 ga) galvanized venting. (Zero clearance)

• 120VAC / single phase.

• 24VAC Honeywell direct ignition valve system.

• Power vented only. Programmed with pre and post-purge safety functioning. Certied to use provided

Town & Country power vent only.

• Horizontal or Vertical Termination.

• Zero clearance unit (no non-combustible board required).

• 12” rigid exhaust - 150ft max length plus up to 6 elbows. (Zero clearance)

• 7” rigid intakes - ( All bottom intake models) 150ft max length plus up to 6 elbows. (Zero clearance)

•

• 12” or 14” rigid intakes - (All top intake models) 150ft max length plus up to 6 elbows. (Zero clearance)

5Architectural Series

160819-52 100000847

Minimum Clearances to Combustible Material

Vent Terminal Minimum Clearances

Installation Requirements

The replace installation and venting must conform to the current CAN/CGA-B149 installation code

(in Canada) or the current National Fuel Gas Code, ANSI Z223.1 (in the USA), and approved per

local codes. Only qualied (licensed or trained) personnel should install this product.

In the state of Massachusetts, only a licensed Plumber and Gas Fitter may install this product.

This appliance is a zero clearance re feature. Combustible material may be use to frame the unit in.

Venting for this unit is also zero clearance. Combustible material is permitted to come into direct

contact with venting material.

Refer to the Power Vent installation instructions which are included with the power vent.

6100000847 160819-52Architectural Series

8"18

16"

11 1

19 3

50 5"

15 1"

1"18 2

13 "17 16

9"16 16

1"45 4

1 1

18"24"

12" 12"

15" 15"

21" 21"

18"18" 18"

24"

Ø11 7/8”

Ø6 15/16”

3’ 4’ 5’ 6’ 7’ 8’

A 51 1/2” 63 1/2” 75 1/2” 87 1/2” 99 1/2” 111 1/2”

B 53 1/4” 65 1/4” 77 1/4” 89 1/4” 101 1/4” 113 1/4”

C 50 1/4” 62 1/4” 74 1/4” 86 1/4” 98 1/4” 110 1/4”

Top view of replace

Appliance Dimensions

Peninsula Dimensions using 16 inch

High Glass

7Architectural Series

160819-52 100000847

24"

12" 12"

15" 15"

21" 21"

18"18" 18"

18" 24"

24"

18 1

11 1

17 13

24 9

53 1

58 5

15 1 1 "

18 1

19 3

Ø11 7/8”

Ø6 15/16”

3’ 4’ 5’ 6’ 7’ 8’

A 51 1/2” 63 1/2” 75 1/2” 87 1/2” 99 1/2” 111 1/2”

B 53 1/4” 65 1/4” 77 1/4” 89 1/4” 101 1/4” 113 1/4”

C 50 1/4” 62 1/4” 74 1/4” 86 1/4” 98 1/4” 110 1/4”

Top view of replace

Peninsula Dimensions using 24 inch

High Glass

8100000847 160819-52Architectural Series

Minimum Clearances to Combustible Material

Btu Values and Weights

This appliance is a zero clearance re feature.

Combustible material may be used to frame this unit in.

Venting for this unit is also zero clearance.

Combustible material is permitted to come into direct contact with venting material.

Peninsula 3FT 4FT 5FT 6FT 7FT 8FT

BTR/HR 48000 64000 80000 96000 112000 128000

16” Glass 500 570 640 710 780 850

Weight lbs

24” Glass 470 540 610 680 750 820

Weight lbs

9Architectural Series

160819-52 100000847

Locating the Unit

Horizontal

Termination

Vertical

Termination

Vertical Termination

Power Vent

Air Intakes

Power Vent

Supporting wall

Figure 1: Linear appliance location options.

The Architectural Series Linear Appliances are power vent only, and because of this, they can be

located in a variety of places. Consideration must be taken for the location of the fresh air intake and

the power vent unit venting. A site fabricated platform capable of supporting the appliances weight

may be constructed to elevate the viewing area to the desired height, as well as accommodate the

fresh air intake - (if bottom vented), gas supply and electrical supply.

10 100000847 160819-52Architectural Series

Andere Handbücher für Architectural Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Town & Country Fireplaces Kamin im Innenbereich Handbücher

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCW120 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.RHKA Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54NG04.C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36ARCH Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Gebrauchsanweisung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.38CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces Model TC42SeriesC Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36ST Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30D2 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30 Black Diamond Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42.NG01 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.38NG03.C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54NG04.C2 Technisches Handbuch

Town & Country Fireplaces

Town & Country Fireplaces TCW120 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 SEE-THRUC SERIES Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch