Town & Country Fireplaces TC36ST Bedienungsanleitung

070617-40 TC36D_ST 5056.42801D

MODEL

TC36ST

SERIES D

MODULAR DIRECT VENT

SEE-THRU FIREPLACE

TC36 SEE THRU

INSTALLATION

INSTRUCTIONS

WARNING: If the information in these

instructions is not followed exactly, a re or

explosion may result causing property damage,

personal injury or death.

This appliance may be installed in an aftermarket

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certied kit is used.

This appliance is suitable for installation in a

bedroom or bed sitting room

FOR YOUR SAFETY

Do not store or use gasoline or other

ammable vapors and liquids in the vicinity of

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Donottrytolightanyappliance.

• Donottouchanyelectricalswitch.

•Donotuseanyphoneinyourbuilding.

• Immediately call your gas supplier from a

neighbour’s phone.Follow the gas supplier’s

instructions.

• If you cannot reachyourgassupplier call

the re department.

Installation and service must be performed by

a qualied installer, service agency or the gas

supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Visit www.townandcountryﬁreplaces.com for the most up-to-date version of this manual

INSTALLATION INSTRUCTIONS

TC36D_ST

Table of Contents

Caution ............................................................................ 3

Safety .............................................................................. 3

Important Note for the

Commonwealth of Massachusetts:.................................. 4

Fireplace Dimensions ...................................................... 5

Minimum Clearances to Combustible Material ............... 5

Installation Requirements ................................................ 6

Manufactured (Mobile) Home .......................................... 6

Window Frame Removal ................................................. 6

Top Standoffs .................................................................. 7

Locating The Fireplace .................................................... 7

Framing and Finishing ..................................................... 8

Minimum Combustible Framing Dimensions .................. 9

TC36 Steel Stud Framing Kit ......................................... 10

Fixed Lintel .................................................................... 13

Hearth Extension ........................................................... 14

Electrical ........................................................................ 15

Wall Switch and Remote Control .................................. 16

Selecting Natural Vent and Power Vent Modes ............. 16

Home Automation ......................................................... 17

Gas Supply .................................................................... 18

Gas Pressure Check ...................................................... 18

Venting ........................................................................... 19

Wall Termination Venting ............................................... 19

Wall Termination Venting Chart ..................................... 22

Roof Termination Venting Chart ..................................... 23

Vent Terminal Clearance ................................................ 26

Vent Terminal Minimum Clearances .............................. 26

Vent Pipe Sealant .......................................................... 27

Vent Restrictor Adjustment ........................................... 28

Wall Shield Ceiling Firestop Thimble.............................. 29

Wall Termination Kit ....................................................... 29

Roof Termination Kit ...................................................... 29

Vent Pipe Dimensions ................................................... 30

Vent Offset Chart ........................................................... 31

Firebox Panels Installation ............................................ 32

Finishing Touch Trim Kit Instructions ............................. 33

Lighting Instructions ...................................................... 34

Maintenance .................................................................. 35

TC36.DST Replacement Parts ...................................... 36

Replacement Parts – Control System ........................... 37

Wiring Diagram .............................................................. 38

Rating Label Location ................................................... 39

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

DANGER

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with the appliance and

shall be installed for the protection of children and

other at-risk individuals.

25056.42801D_070617-40

TC36D_ST

FOR YOUR SAFETY - Do not install or operate your Town & Country replace

without rst reading and understanding this manual. Any installation or

operational deviation from the following instructions voids the Town & Country

FireplacesTM Warranty and may prove hazardous.

This appliance and its individual shut off valve must be disconnected from

gas supply piping system during any pressure testing of that system at test

pressures in excess of 1/2 psig (3.5 kPa).

This appliance must be isolated from the gas supply piping system by closing

its individual manual shut off valve during any pressure testing of the gas

supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).

Note: When lit for the rst time, the appliance will emit a slight odour for a

couple of hours. This is due to the curing of paints, sealants and lubricants

used in the manufacturing process. This condition is temporary. Open doors

and windows to ventilate area. Smoke and fumes caused by the curing

process may cause discomfort to some individuals.

Do not use the replace if any part has been under water. Immediately call a

qualied service technician to inspect the replace and to replace any part of

the control system and any gas control which has been under water.

Due to high temperatures, this gas appliance should be located out of trafc and away from furniture and draperies.

Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns

or clothing ignition.

Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young

children, and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are

at-risk individuals in the house. To restrict access to a replace or stove, install an adjustable safety gate to keep

toddlers, young children, and other at-risk individuals out of the room and away from hot surfaces.

Clothing or other ammable material should not be placed on or near the appliance.

Any grill, panel or door removed for servicing the unit must be replaced prior to operating. Failure to do so may create a

hazardous condition.

Installation and repair should be done by a qualied service person. The appliance should be inspected before use and

at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from

carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of

the appliance be kept clean.

It is our policy that no responsibility is assumed by the Company or by any of its employees or representatives for any

damages caused by an inoperable, inadequate, or unsafe condition which is the result, either directly or indirectly, of any

improper operation or installation procedures.

This appliance must not be connected to a chimney ue serving a separate solid fuel burning appliance.

We recommend that our gas

hearth products be installed and

serviced by professionals who are

certied in the United States by

the National Fireplace Institute®

(NFI) as NFI Gas Specialists

5056.42801D_070617-40

Safety

Caution

TC36D_ST

Important Note for the Commonwealth of Massachusetts:

From Massachusetts Rules and Regulations 248 CMR 5.08:

(a) For all side wall horizontally vented gas fuelled equipment installed in every dwelling, building or structure used in whole or in part for residential

purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet

above nished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satised.

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fuelled equipment, the

installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the oor

level where the gas equipment is to be installed, in addition, the installing plumber or gas tter shall observe that a battery operated or hard-wired

carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal

vented gas fuelled equipment. It shall be the responsibility of the property owner to secure the services of qualied licensed professionals for the

installation of hard-wired carbon monoxide detectors.

a. In the event that the side wall horizontally vented gas fuelled equipment is installed in a crawl space or an attic, the hard-wired carbon monoxide

detector with alarm and battery back-up may be installed on the next adjacent oor level.

b. In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall have a period of thirty

(30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide

detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall

comply with NFPA 720 and be ANSI/UL 2034 listed as IAS certied.

3. SIGNAGE. A metal or plastic identication plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet

above grade directly in line with the exhaust vent terminal for the horizontally vented gas fuelled heating appliance or equipment. The sign shall

read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fuelled equipment shall not approve the installation unless,

upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.089(2)

(a) 1 through 4.

(b) EXEMPTIONS. The following equipment is exempt from 248 CMR 5.089(2)(a) 1 through 4.

1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the

Board; and

2. Product Approved side wall horizontal vented gas fuelled equipment installed in a room or structure separate from the dwelling, building or structure

used in whole or in part for residential purposes.

(c) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side wall

horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided

by the manufacturer for installation of the equipment and the venting system shall include:

1. Detailed instructions for the installation of the venting system design or the venting system components; and

2. A complete parts list for the venting system design or venting system.

(d) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved

side wall horizontally vented gas fuelled equipment does not provide the parts for venting the fuel gases, but identies “special venting systems”, the

following requirements shall be satised by the manufacturer.

1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed

installation instructions.

(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fuelled equipment, all venting instructions, all parts

lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

45056.42801D_070617-40

Minimum Clearances:

Side standoffs ........................................................... 0 in. (0 mm)

Back standoffs .......................................................... 0 in. (0 mm)

Top standoffs............................................................. 0 in. (0 mm)

Bottom of appliance.................................................. 0 in. (0 mm)

Adjacent side wall ..................................................... 2 in. (51 mm)

Ceiling to appliance................................................. 24 in. (610 mm)

*Mantel to appliance...................................See Figure #2

**Maximum Mantel extension ..................See Figure #2

Mantel support .......................................................... 2 in. (51 mm)

Vertical vent pipe .............................................. 1 3/4" in. (45 mm)

Horizontal Vent pipe (Top, sides and bottom) ... 1 3/4" in. (45 mm)

MANTEL

ADJACENT WALL

OR MANTEL SUPPORT

CEILING

UNIT MAY BE RECESSED UP TO 4 1/2”

WITH NON-CUMBUSTIBLE MASONRY

TYPE MATERIAL

Figure 3: TC36ST Mantel.

TC36D_ST

Figure 2: TC36ST Mantel clearances.

* MANTEL CLEARANCE

A 9”

B 6”

C 3”

** MANTEL DEPTH

D 12”

E 6 3/4”

F 1 1/2”

MANTEL CLEARANCE

CHART

MAY USE COMBUSTIBLE

FACING MATERIAL IN THIS AREA

NON-COMBUSTIBLE

FINISH MATERIAL

SEE FIGS #10 - 12

NON-COMBUSTIBLE ZONE.

DO NOT INSTALL ANY COMBUSTIBLE MATERIAL,

ELECTRICAL WIRING OR GAS PLUMBING IN THIS

AREA.

COMBUSTIBLE FRAMING AND

FINISH WALL ABOVE STANDOFFS STANDOFFS

STEEL FRAMING

FIREPLACE FRONT

TOP OF LINTEL BAR

32 1/2"

8 11/16"

48 1/16"

38 1/2"

32 1/2"

28 7/16"

41 1/4"

55 15/16"

46 7/16"

3 9/16"

Figure 1: TC36ST Overall dimensions.

5056.42801D_070617-40

Fireplace Dimensions

Minimum Clearances to Combustible Material

TC36D_ST

Figure 4: Safety barrier

screen.

Figure 5: Accessing

handle.

Figure 6: Handle.

The Town & Country Fireplace installation and venting must conform to the current CAN/CGA-B149 installation code (in

Canada) or the current National Fuel Gas Code, ANSI Z223.1 (in the USA), and approved per local codes. Only qualied

(licensed or trained) personnel should install this product.

In the state of Massachusetts, only a licensed Plumber and Gas Fitter may install this product.

In some jurisdictions, the Town & Country Fireplace may be installed in Manufactured Homes after the "rst sale".

Consult local codes for approval. The replace must be fastened in place.

Install in accordance with the current standard Mobile Homes, CAN/CSA Z240 MH (in CANADA), and the Manufacturer's

Home Construction and Safety Standard, Title 24 CFR, Part 3280 or the current Standard for Fire Safety Criteria for

Manufactured Home Installations, Sites and Communities ANSI/NFPA 501A (in the USA).

Warning: Turn off the ﬁreplace, and allow ample time for the unit to cool before proceeding.

Caution: The ceramic glass is very fragile, and should be handled with care.

The window frame is held in place by two spring-loaded latches that are operated by a one-piece latch handle.

1. Remove safety barrier screen (Figure 4) by prying the top portion of the screen toward you , then lift the screen from

its tabs (inset) located at the base of the window frame.

2. Remove the TC Finishing Touch Trim Kit from the window frame. (If installed)

3. Using a screwdriver (Figure 5) or other similar object, push against the notch in the top of the latch and grab the bot-

tom of the latch handle as it protrudes (Figure 6). Lift handle until latch hook disengages. Repeat for other side while

holding glass so it does not tip out.

4. Tilt the top of the window frame out to clear the top edge of the unit. Grasp the sides of the frame and lift up and out

to disengage from its bottom track.

5. Place the window frame in a safe place to avoid damage.

6. Re-assemble in reverse order. Latch handle should snap into place and be ush with window frame when engaged

correctly.

7. Reinstall Trim Kit if required.

8. Reinstall the safety barrier screen.

Installation Requirements

Manufactured (Mobile) Home

Window Frame Removal

TIP:

To ensure glass door is

properly latched, grasp the

top left and right sides of the

glass frame. Under moderate

pressure it should pull forward

and return to original position

evenly on both sides.

HANDLE

65056.42801D_070617-40

TC36D_ST

Figure 7: TC36ST Standoffs.

The top standoffs are shipped loose inside the replace and must be installed on top of the replace (Figure 7). Do this

once the replace is on site and in position.

In planning the installation for the replace, it is necessary to determine where the unit is to be installed, location of vent

system and where gas supply piping may be plumbed. Various installations are possible, such as, into an existing wall, a

corner, a built-in wall or a wall projection (Figure 8). Due to high temperatures, do not locate this replace in areas of high

trafc or near furniture or draperies.

The minimum clearances from the ﬁreplace to combustible surfaces must be adhered to as described in

Figure 2 & Figure 3.

TOP STANDOFFS

Figure 8: TC36ST Possible locations.

5056.42801D_070617-40

Locating The Fireplace

Top Standoffs

TC36D_ST

NOTE: FOR CLARITY ONLY

ONE FACE OF THE TWO-

SIDED FIREPLACE IS SHOWN

WITH STEEL STUD FRAMING

KIT ATTACHED. BOTH FACES

MUST BE FRAMED WITH

THE STEEL STUD FRAMING

KIT SUPPLIED WITH THE

FIREPLACE.

NOTE:

The chase must be properly

sealed at the ceiling level or

between oors in a multilevel

installation.

48 1/2”

59 1/2”

Figure 9: TC36ST With supplied steel frame.

Note: The replace should be in place

and venting installed before framing in or

building an enclosure around the unit.

The Town & Country replace must be

framed in as described below or totally

enclosed with non-combustible material,

such as facing brick.

Determine the total thickness of facing

material to be used. A thickness of 3/4"

will allow the nishing surface to be ush

with the front of the unit. If preferred,

additional masonry type non-combustible

material can be installed above and to

the sides up to 4 1/2 inches proud of the

appliance.

The nishing material must not interfere

with glass frame access.

Two Steel Stud Framing Kits are supplied

with the replace and must be used unless

the replace is totally enclosed with non-

combustible material. Assemble the fram-

ing kit as per the instructions on pages 10

& 11 of this manual. Attach the steel frame

to the replace once the replace is in its

nal position. Secure the steel frame to

the framing brackets on each side of the

unit. Ensure that the studs are set back far

enough to allow for thickness of nishing

surface.

The sides, back and top of the replace

can be framed in up to the steel studs and

the replace standoffs using conventional

lumber. Consult local building codes for

specic requirements.

Due to high temperatures, non-combusti-

ble backer board, such as cement board

or its equivalent, must be used to sheet

in the front of the replace, extending 12"

above and 9 3/4" to the side of the fram-

ing edge bars (Figure 10). Standard sheet

rock (dry wall) may be used beyond this.

If the backer board is not to be nished

with other non-combustible material

such as tiles, it is recommended that the

instructions in (Figure 12) be followed

closely.

Chase Insulation: When installing this

ﬁreplace against a non-insulated exte-

rior wall or chase, it is recommended

that the outer walls be insulated to

same degree as other exterior walls.

Do not place ﬁreplace directly against

the insulation. Cover the insulation

and plastic vapour barrier with a solid

surface, such as dry wall (sheet rock).

Consult local codes. Do not insulate

or use plastic vapour barrier within the

framing kit.

CAUTION: See Figure 12 BEFORE

PROCEEDING.

IT IS HIGHLY

RECOMMENDED THAT

A FULL HEADER BE

INSTALLED ABOVE THE

METAL FRAMING KIT

NON-COMBUSTIBLE ZONE. DO NOT INSTALL ANY

COMBUSTIBLE MATERIAL, ELECTRICAL WIRING,

INSULATION, PLASTIC VAPOR BARRIER OR GAS

PLUMBING WITHIN THE STEEL STUD FRAMING ALL OTHER FRAMING CAN

BE DONE WITH

CONVENTIONAL LUMBER

STEEL STUD FRAMING KIT DIMENSIONS

(Supplied with replace)

85056.42801D_070617-40

Framing and Finishing

TC36D_ST

10 1/4”

Figure 10: Non-combustible board dimensions.

Figure 11: Reccessed installation details.

MINIMUM COMBUSTIBLE

FRAMING DIMENSIONS

RANGE

23 3/4"

27 1/4"

28 1/4"

1/2"

For nishing

material

FRAMING

LINTEL

59 1/2"

INCLUDING SHEETROCK

48 1/2"

1/2"

For nishing

material

Figure 13: TC36ST Minimum combustible framing dimensions.

NON-COMBUSTIBLE

BOARD

NON-COMBUSTIBLE

BOARD DETAIL

NON-COMBUSTIBLE

MATERIAL MUST EXTEND

12" ABOVE AND 10 1/4" TO

THE SIDES OF THE FRAMING

EDGES.

NON-COMBUSTIBLE BOARD

5056.42801D_070617-40

If nishing the wall above the unit with

paint, the framing kit shipped with

the unit should be discarded. Use full

sheets of calcium silicate board or

equivalent and full length metal studs to

nish and frame around the unit.

Calcium silicate board is a high grade

material with cement, quartz and natural

minerals as the main raw materials.

(Note: Calcium Silicate is 1/2” thick)

CAUTION: Calcium Silicate board

can be damaged if dropped or struck.

Handle with care. Inspect board prior to

installation and do not use if cracked.

NOTE: It is recommended to pre-drill

mounting holes in the board prior to

securing to the framing. This will pre-

vent the board from cracking.

Minimum Combustible Framing Dimensions

Figure 12: Non-combustible calcium

silicate board..

TC36D_ST

Figure 14: TC36ST Steel frame parts.

Each Kit Contains:

Item Description Qty.

1 SCREW, TEKS #8 x 1/2

(Not shown)

Pkg

2 SIDE STUD, VERTICAL INNER

48 1/4”

3 SIDE STUD, VERTICAL OUTER

48 1/4”

4 STUD, CENTER 15 1/2”

VERTICAL SHORT

Item Description Qty.

5 STUD, HEADER 59 1/2

HORIZONTAL

6 STUD PLATE 41 1/4”

HORIZONTAL

7 BASE PLATE 2

8 FRAMING PLATE 4

10 5056.42801D_070617-40

TC36 Steel Stud Framing Kit

Andere Handbücher für TC36ST

Inhaltsverzeichnis

Andere Town & Country Fireplaces Kamin im Innenbereich Handbücher

Town & Country Fireplaces

Town & Country Fireplaces TCWS.38CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCW120 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54ST SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.NG03D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Einrichtungshandbuch

Town & Country Fireplaces

Town & Country Fireplaces TC30 Black Diamond Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54.CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCVT.WSPVB1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces Series C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces D2 Series Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.OD Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces T120.RHKIT Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces HELIFIRE 360 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.CSTE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces Model TC42SeriesC Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch