Ubiquiti EdgePoint R8 Bedienerhandbuch

Intelligent WISP Control

with FiberProtect™

Model: EP-R8

Introduction

Thank you for purchasing the Ubiquiti Networks® EdgePoint™

Router. This Quick Start Guide is designed to guide you through

installation and includes the warranty terms.

Package Contents

EdgePoint Router Wall-Mount

Bracket

Metal Straps

(Qty. 2)

Cable Sleeve

Intelligent WISP Control

with FiberProtect™

Model: EP-R8

Gigabit PoE (54V, 1.5A) with

Mounting Bracket

Power Cord Quick Start

Guide

Installation Requirements

• 7 mm socket wrench

• S2 hex wrench

• Ground wire – min. 10 AWG (5 mm2) and max. length: 1m. Asa

safety precaution, ground the EdgePoint to a grounded mast,

pole, tower, or grounding bar.

• Shielded Category 5 (or above) cabling should be used for all

wired Ethernet connections and should be grounded through

the AC ground of the PoE.

• We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit: www.ubnt.com/toughcable

warranty. TOUGHCable™is designed for outdoor installations. It is the customer’s responsibility to

follow local country regulations, including operation within legal frequency channels, output power,

and Dynamic Frequency Selection (DFS) requirements.

Introduction

Hardware Overview

Bottom Panel Button

Reset

Button Description

Reset

There are two methods to reset the EP-R8 to

factory defaults:

Runtime Reset (Recommended)

The EP-R8 should be running after bootup is

complete. Press and hold the Reset button

for about 10seconds until the eth7 or SFP2

LED starts flashing and then becomes solidly

lit (the SFP 2 LED is used if there is an SFP

module connected to the SFP 2 port). After

a few seconds, the LED will turn off, and the

EP-R8 will automatically reboot.

Power-on Reset

1. Disconnect power from the EP-R8.

2. Press and hold the Reset button while

connecting power to the EP-R8. Keep

holding the button until the eth7 or SFP 2

LED starts flashing and then stops flashing

after a few seconds (the SFP 2 LED is used

if there is an SFP module connected to the

SFP 2 port).

EdgePoint EP-R8 Quick Start Guide

Bottom Panel Console Port

Console

Interface Description

Console

RJ45 serial console port for Command

Line Interface (CLI) management. Use an

RJ45-to-DB9, serial console cable, also known

as a rollover cable, to connect the Console

port to your computer. (If your computer does

not have a DB9 port, then you will also need

a DB9 adapter.) Then configure the following

settings as needed:

• Baud rate 115200

• Data bits 8

• Parity NONE

• Stop bits 1

• Flow control NONE

Note: Remove the protective plug from the Console port

before use.

Hardware Overview

Power Options

Either the VDC or PoE input type is used at any one time. If both

are connected, only the input type with the highest voltage will be

used; the other can be used as a backup.

Both PoE inputs can be used at the same time. If there is a voltage

difference, the higher-voltage source will be used first. The voltage

from the initial source will drop as the load increases. When the

voltage drops to the same level as the lower-voltage source, then

the lower-voltage source will also start providing power.

Power Input Options

• 54VDC, 6A

• 54V, 1.5A on eth0 (PoE In)

• 54V, 1.5A on PoE In

Power Output Options

• EdgePoint (required)

• Passive 54/24V, 4-Pair PoE on

eth1-eth2

• Passive 24V, 2-Pair PoE on

eth3-eth7

The number of devices that can be powered depends on the

power consumption of the specific devices. Example: If you use

54VDC, 1.5A, then you have 81W. If the EdgePoint uses 40W, then

you have 41W for PoE output. Check product specifications for the

power consumption values to use in your calculations.

Bottom Panel DC Input

VDC

Interface Description

VDC In

Terminal block connector uses auto-polarity

detection and accepts +42 to +56VDC, 6A

input (including the Ubiquiti EdgePower™,

model EP-54V-150W) to power the EdgePoint

and passive PoE output. -48V is NOT supported.

EdgePoint EP-R8 Quick Start Guide

Bottom Panel RJ45 Ports

PoE In

eth0

eth1-2

eth3-7

Interface Description

PoE In

Accepts 54V, 1.5A PoE input from a secondary

PoE adapter (not included) to power the

EdgePoint and passive PoE output.

PoE In / eth0

Accepts data and 54V, 1.5A PoE input from

the included Gigabit PoE Adapter to power the

EdgePoint and passive PoE output.

eth1-2

(54/24V

PoE Out)

RJ45 ports support 10/100/1000 Ethernet

connections and passive 54/24V, 4-pair PoE

output for airFiber® devices.

eth3-7

(24V PoE Out)

RJ45 ports support 10/100/1000 Ethernet

connections and passive 24V, 2-pair PoE

output for airMAX® devices.

RJ45 port eth6 or eth7 is active only if the

corresponding SFP port is empty.

Note: The USB port is reserved for future use.

Hardware Overview

Bottom Panel SFP Ports

SFP 1-2

Interface Description

SFP 1-2

SFP ports are hot-swappable and support

100 Mbps or Gigabit fiber SFP modules. If an

SFP module is plugged in, then the SFP port

is active, and the corresponding RJ45 port is

deactivated.

Note: For extreme temperatures, please use industrial-grade

fiber SFP modules.

Front Panel LEDs

LED State Status

eth0

Speed/

Link/Act

Off No Link

Amber 10/100Mbps Link

Flashing Indicates Activity

Green 1000Mbps (1 Gbps) Link

Flashing Indicates Activity

EdgePoint EP-R8 Quick Start Guide

LED State Status

power

Green EdgePoint Powered On

eth1-2

Speed/

Link/Act

Off No Link

Amber 10/100Mbps Link

Flashing Indicates Activity

Green 1000Mbps (1 Gbps) Link

Flashing Indicates Activity

PoE

Output

Off No PoE

Amber 54V, 4-Pair Passive

Green 24V, 4-Pair Passive

eth3-7

Speed/

Link/Act

Off No Link

Amber 10/100Mbps Link

Flashing Indicates Activity

Green 1000Mbps (1 Gbps) Link

Flashing Indicates Activity

PoE

Output

Off No PoE

Green 24V, 2-Pair Passive

SFP 1-2

Speed/

Link/Act

Off No Link

Amber 100Mbps Link

Flashing Indicates Activity

Green 1000Mbps (1 Gbps) Link

Flashing Indicates Activity

Hardware Overview

Back Panel

PicoStation Slot

Lanyard Loop

Pole-Mount

Bracket

Ground

Bonding Point

Lanyard Loop Used for temporary support during installation.

PicoStation®M2HP Slot Used for mounting an optional

PicoStationM2HP (not included) to the back of the EdgePoint. (You

can use the PicoStationM2HP for wireless management of the

EdgePoint.)

Pole-Mount Bracket Used for pole-mounting or in combination

with the included Wall-Mount Bracket for wall-mounting.

Ground Bonding Point Used to secure a ground wire (not

included).

EdgePoint EP-R8 Quick Start Guide

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Router Handbücher

Ubiquiti

Ubiquiti EdgeRouter ERPro-8 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ER-10X Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti ROcket M5 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ER-12P Bedienungsanleitung

Ubiquiti

Ubiquiti ER-4 Bedienungs- und Wartungsanleitung

Ubiquiti

Ubiquiti ER-8-XG Bedienungsanleitung

Ubiquiti

Ubiquiti UFiber UF-WIFI Gebrauchsanweisung

Ubiquiti

Ubiquiti ER-12 Bedienungsanleitung

Ubiquiti

Ubiquiti LTU LR Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ER-8 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ER-8 Bedienungsanleitung

Ubiquiti

Ubiquiti ERLite-3 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 6P Bedienungsanleitung

Ubiquiti

Ubiquiti UCK-G2 Bedienungsanleitung

Ubiquiti

Ubiquiti Amplifi AFi-LR Bedienungsanleitung

Ubiquiti

Ubiquiti airCube Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgePoint EP-R8 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 10X Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBridge M3 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter Lte 3 Bedienungsanleitung

Ubiquiti

Ubiquiti ERLite-3 Bedienungsanleitung

Ubiquiti

Ubiquiti edgerouter X SFP Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung