Ubiquiti Edgerouter X SFP Bedienungsanleitung

Advanced Gigabit Router

with PoE and SFP

Model: ER-X-SFP

Introduction

Thank you for purchasing the Ubiquiti Networks®

EdgeRouter™X SFP. This Quick Start Guide is designed to guide

you through installation and also includes warranty terms.

Package Contents

EdgeRouter X SFP Power Adapter

(24V, 2.5A)

Advanced Gigabit Router

with PoE and SFP

Model: ER-X-SFP

Power Cord Quick Start Guide

responsibility to follow local country regulations, including operation within legal frequency

channels, output power, indoor cabling requirements, and Dynamic Frequency Selection

(DFS) requirements.

Installation Requirements

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial‑grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit

www.ubnt.com/toughcable

WARNING: To reduce the risk of fire or electric shock, do

not expose the EdgeRouter X SFP to rain or moisture.

Note: Although the cabling can be located outdoors,

the EdgeRouter X SFP itself should be housed inside

a protective enclosure.

Hardware Overview

Front Panel

SFP (eth5/SFP) RJ45 (eth0-eth4)

Port Description

eth5/SFP The SFP port is hot-swappable and supports

a 100 Mbps or Gigabit fiber SFP module.

eth0‑eth4 RJ45 ports support passive 24V PoE output

and 10/100/1000 Ethernet connections.

Top Panel

Power PoE

Link/Act

LED State Status

Power

Status

Off Power Off

Green Power On

eth5

Link/Act

Off No Link

Green 100/1000Mbps (1 Gbps) Link

Flashing Indicates Activity

eth0‑eth4

PoE

Off No PoE

Green 24V Passive

Link/Act

Off No Link

Green 10/100/1000Mbps Link

Flashing Indicates Activity

Back Panel

Power

Ground

Reset

Button Description

Reset

There are two methods to reset the

EdgeRouter X SFP to factory defaults:

Runtime Reset (Recommended)

The EdgeRouter X SFP should be running after

bootup is complete. Press and hold the Reset

button for about 10 seconds until the eth4

Link LED starts flashing and then becomes

solidly lit. After a few seconds, the LED will

turn off, and the EdgeRouter X SFP will

automatically reboot.

Power-on Reset

1. Disconnect the Power Adapter from the

EdgeRouter X SFP.

2. Press and hold the Reset button while

connecting the Power Adapter to the

EdgeRouter X SFP. Keep holding the button

until the eth4 Link LED starts flashing and

then stops flashing after a few seconds.

Detail Description

Ground

The EdgeRouter X SFP is grounded through

the Power Adapter; however, you can add

optional ESD grounding for enhanced ESD

protection. The ground wire and screw with

washer are not included (recommended

screw size: M3-0.5 x 4 mm).

Power Connect the Power Adapter.

Hardware Installation

Place the EdgeRouter X SFP on a flat, horizontal surface or

mount it on a wall (mounting screws not included).

WARNING: FAILURE TO PROVIDE PROPER VENTILATION

MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF

CLEARANCE NEXT TO THE VENTILATION HOLES FOR

ADEQUATE AIRFLOW.

Connecting Power

1. Connect the Power Adapter to the Power port.

2. Connect the Power Cord to the Power Adapter. Connect the

other end of the Power Cord to a poweroutlet.

Connecting Ethernet

1. Connect an Ethernet cable from your computer or host

system to the port labeled eth0 on the EdgeRouter X SFP.

Note: PoE is disabled by default.

2. Connect Ethernet cables from the Ethernet ports of your

devices to the rest of the ports in this range: eth1‑eth4.

Using the SFP Port (Optional)

To use the eth5/SFP port:

1. Remove the protective plug covering the eth5/SFP port.

2. Plug a fiber SFP module into the eth5/SFP port.

1000Mbps SM/SC 20KM DDM

Tx1550nm/Rx1310nm

SN: 1 308 261 79

EF -1 000 M- 20 KM -1 5

3. Connect a fiber optic cable to the fiber SFP module. Then

connect the other end of the cable to another fiber device.

For information about compatible fiber SFP modules, visit:

community.ubnt.com/edgemax

Accessing the Configuration Interface

Note: Ensure that your host system is connected to the

eth0 port of the EdgeRouter X SFP.

1. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet.

2. Launch your web browser. Type https://192.168.1.1 in the

address field. Press enter (PC) or return (Mac).

3. The login screen will appear. Enter ubnt in the Username

and Password fields. Read the Ubiquiti License Agreement,

and check the box next to I agree to the terms of this License

Agreement to accept it. Click Login.

The EdgeOS Configuration Interface will appear, allowing

you to customize your settings as needed. You can click the

Wizards tab to access the Setup Wizards. For information on

PoE configuration, refer to the Configuring PoE Settings section.

Configuring PoE Settings

WARNING: Before activating 24V passive PoE, ensure

that the connected device supports PoE and the

suppliedvoltage.

1. On the Dashboard screen, go to Actions > PoE for the

interface you want to configure.

2. Select 24V from the PoE drop-down menu.

3. ClickSave.

For more information, refer to the EdgeOS User Guide, which is

available at documentation.ubnt.com/edgemax

*640-00150-02*

640-00150-02

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Router Handbücher

Ubiquiti

Ubiquiti EdgeRouter ER-8 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter X ER-X-SFP Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 4 Bedienungsanleitung

Ubiquiti

Ubiquiti ER-4 Bedienungs- und Wartungsanleitung

Ubiquiti

Ubiquiti UDM Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USG Bedienungsanleitung

Ubiquiti

Ubiquiti ERLite-3 Bedienungsanleitung

Ubiquiti

Ubiquiti AFi-ALN Bedienungsanleitung

Ubiquiti

Ubiquiti TS-5-POE ToughSwitchPoE Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ER-8 Bedienungsanleitung

Ubiquiti

Ubiquiti airCube Bedienungsanleitung

Ubiquiti

Ubiquiti ERLite-3 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 6P Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti LTU LR Bedienungsanleitung

Ubiquiti

Ubiquiti UFber UF-WIFI Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ERPro-8 Bedienungsanleitung

Ubiquiti

Ubiquiti ERLite-3 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter LITE Bedienungsanleitung

Ubiquiti

Ubiquiti airCube Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter X ER-X Bedienungsanleitung

Ubiquiti

Ubiquiti ToughSwitch Pro TS-80-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PRO Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Ubiquiti edgerouter X SFP Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken