Ubiquiti LiteBeam LBE-5AC-Omni Bedienungsanleitung

High-Performance

airMAX®ac Omni

Model: LBE-5AC-OMNI

Introduction

Thank you for purchasing the Ubiquiti Networks® LiteBeam™ac

Omni. This Quick Start Guide is designed to guide you through

installation and also includes warrantyterms.

Package Contents

Antenna

Feed with Omni

Rear

Housing

Mounting

Bracket

Pole Clamp

U-Bolt Bolts (Qty. 4) Flange Nuts (Qty. 2) Washers (Qty. 2)

High-Performance

airMAX®acOmni

Model:LBE-5AC-OMNI

Gigabit PoE (24V, 0.5A)

with Mounting Bracket

Power

Cord

Quick Start

Guide

Installation Requirements

• Phillips screwdriver

• 10 mm wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

Port View

RESET

Reset

Ethernet

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the LiteBeam is

already poweredon. Alternatively, the LiteBeam may be reset

remotely via a Reset button located on the bottom of the

Gigabit PoE adapter.

Release Button

Release Button After you assemble the LiteBeam, check the

Release button; it should be fully engaged in the Release Button

Slot of the Rear Housing. This ensures that the Antenna Feed is

locked into place. If you need to remove the Antenna Feed, you

must depress the Release button first.

LEDs

Signal The default values (from left to right) are

shown below:

LED will light blue when the wireless signal

strength is equal to or above -65 dBm.

LED will light blue when the wireless signal

strength is equal to or above -73 dBm.

LED will light blue when the wireless signal

strength is equal to or above -80 dBm.

LED will light blue when the wireless signal

strength is equal to or above -94 dBm.

Ethernet The Ethernet LED will light steady blue

when an active Ethernet connection is made and

flash when there is activity.

Power The Power LED will light blue when the

device is connected to a power source.

Installation

1. Insert the Antenna Feed with Omni into the Rear Housing,

and push until it locks into place with a click.

2. Connect an Ethernet cable to the Ethernet port of the

Antenna Feed.

RESET

*640-12345-01*

640-12345-01

3. Attach the Rear Housing to the Mounting Bracket with

fourBolts.

4. Insert the U-Bolt into the Pole Clamp and Mounting

Bracket.Secure each end of the U-Bolt with a Washer and

a FlangeNut.

Note: The mounting assembly can accommodate a

Ø 32 - 56 mm pole.

5. Connect the Ethernet cable from the LiteBeam’s Ethernet

port to the POE port of the Gigabit PoE adapter.

6. Connect an Ethernet cable from your LAN to the adapter’s

LAN port.

7. Connect the Power Cord to the adapter’s power port.

Connect the other end of the Power Cord to a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre-drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the adapter’s slots with the tabs of the PoE Mounting

Bracket, and then slide the adapterdown.

Accessing airOS

Verify connectivity in the airOS Configuration Interface.

1. Make sure that your host system is connected via Ethernet

to the LiteBeam.

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet.

3. Launch your web browser and type https://192.168.1.20

in the address field. Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Select your Country and Language.

You must agree to the Terms of Use to use the product.

Click Login.

Note: For the Country setting, U.S. product versions

are restricted to a choice of Canada, Puerto Rico,

or the U.S. to ensure compliance with FCC/IC

regulations.

The airOS Configuration Interface will appear, allowing you

to customize your settings as needed. For details, refer to the

User Guide available at documentation.ubnt.com/airmax

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti NanoBeam 5AC Gen 2 NBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket R5ACL Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-24HD Bedienungsanleitung

Ubiquiti

Ubiquiti NBE--2AC--13 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation5 Bedienungsanleitung

Ubiquiti

Ubiquiti LTU-Lite Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket Prism AC GEN 2 RP-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti AmpliFi MeshPoint HD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam M Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBridge M5 Bedienungsanleitung

Ubiquiti

Ubiquiti RocketM Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket M2 Titanium RM2-Ti Bedienungsanleitung

Ubiquiti

Ubiquiti IsoStation AC Bedienungsanleitung

Ubiquiti

Ubiquiti BULLETM2-HP-US Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-M5-16 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP AC Lite Bedienungsanleitung

Ubiquiti

Ubiquiti Loco5AC Bedienungsanleitung

Ubiquiti

Ubiquiti Bullet AC-IP67 Bedienungsanleitung

Ubiquiti

Ubiquiti M900 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation M2 Bedienungsanleitung

Ubiquiti

Ubiquiti GigaBeam GBE Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam NBE2ACN Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC PBE-5AC-620 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung