Vicon SVFT-MSH23C Bedienungsanleitung

XX077-01-00

SVFT-MSH Maximum Security Housing

Warning: To reduce a risk of fire or electric shock, do not

expose the indoor unit to rain or moisture.

Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet

your requirements or that the operation will be entirely error free or perform precisely as

described in the documentation. This system has not been designed to be used in life-critical

situations and must not be used for this purpose.

Product specifications subject to change without notice.

Vicon and its logo are registered trademarks of Vicon Industries Inc.

VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788

TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116

24-Hour Technical Support: 800-34-VICON (800-348-4266)

UK: 44/(0) 1489-566300 INFOFAX: 800-287-1207 WEB: www.vicon-cctv.com

Vicon Part No. 8009-8077-01-00 Section 3 Rev 204

Contents

CONTENTS ..........................................................................................................................1

QUICK INSTALLATION .......................................................................................................2

INTRODUCTION...................................................................................................................3

SVFT-MSH Maximum Security Housing Components................................................................................3

Unpacking and Inspection.............................................................................................................................3

Accessory Kit..................................................................................................................................................3

INSTALLATION....................................................................................................................6

Mounting the Unit ...........................................................................................................................................6

OPERATION.......................................................................................................................10

MAINTENANCE..................................................................................................................10

Care and Cleaning of Clear Acrylic Domes ...............................................................................................10

Fuse Replacement........................................................................................................................................10

SHIPPING INSTRUCTIONS ...............................................................................................11

CABLE RECOMMENDATIONS .........................................................................................12

Coaxial Cable ................................................................................................................................................12

Twisted-Pair Cable .......................................................................................................................................13

TECHNICAL INFORMATION .............................................................................................14

XX077-01-00 Rev 204 SVFT-MSH Maximum Security Housing Contents •1

Quick Installation

XX077-01-00 Rev 204 SVFT-MSH Maximum Security Housing Quick Installation •2

Introduction

The information in this manual covers the installation, operation, configuration and maintenance of the SVFT-

MSH Maximum Security Housing. This unit should only be installed by a qualified technician using approved

materials in accordance with national, state and local wiring codes. Read this manual through completely

before attempting installation.

Vicon’s SVFT-MSH offers a rugged, tamperproof and IP65 rated enclosure for the SurveyorVFT Camera

Dome. The SVFT-MSH is sold in thirteen (13) prepackaged configurations with choices in camera type. All

versions use the same firmware for programming and operation. For setup and operational information, refer

to the SurveyorVFT Programming Manual XX134-4X. In addition, refer to the SurveyorVFT Installation

Manual XX134-0X for complete configuration and operation information. This housing can be ceiling or wall

mounted with the appropriate mount. A clear Acrylic Lower Dome is included. Options for this housing are

Mounts and Power Supplies as listed in Table 3. Refer to Table 2 for complete product descriptions.

SVFT-MSH Maximum Security Housing Components

The SVFT-MSH consists of a thick steel enclosure, a sealed Lower Dome assembly, and mounting studs for

the SurveyorVFT Camera Drive. In addition, the housing provides outside holes for external mounting

brackets and tamperproof hardware for Lower Dome removal.

Unpacking and Inspection

All Vicon equipment is tested and inspected before leaving the factory. It is the carrier’s responsibility to

provide suitable delivery. Inspect the cartons upon delivery and, if damage is present, make detailed notes on

the carrier’s bill. Obtain the carrier agent’s signature and file a damage claim as soon as possible.

Open the cartons and inspect the equipment for damage. Save the cartons and packing material. If damage is

present, contact the carrier and file a damage claim immediately. If the equipment must be returned to Vicon

for repair, follow the instructions in the Shipping Information section of this manual.

Accessory Kit

There is one (1) kit included with all configurations of the SVFT-MSH. It provides the necessary hardware to

assist in assembling and wiring the SVFT-MSH. The screws and washers are spares for the Lower Dome.

DESCRIPTION PART NUMBER QUANTITY

Liquid Ti

ht Conduit Fittin

, 3/4 in.

(

19 mm

)

NPT 8001702800 1

Screw, 8-32 x 1/2 in.

(

13 mm

)

, button head 8003729302 2

Washer, Flat, N

lon 8004948501 2

Bit, Tamperproof, 1/4 in. (6.5 mm) hex drive 8003735406 1

Table 1

Accessories

XX077-01-00 Rev 204 SVFT-MSH Maximum Security Housing Introduction •3

Model Product

Code Description

SVFT-MSH23 8714-00

1/4-in. color camera, NTSC version, 23x zoom, high-resolution day/night camera,

variable-speed camera dome, aluminum upper housing with lower acrylic dome,

mountin

bracket not included

SVFT-MSH23C 8714-01

1/4-in. color camera, PAL version, 23x zoom, high-resolution day/night camera,

variable-speed camera dome, aluminum upper housing with lower acrylic dome,

mounting bracket not included

SVFT-MSH22 8713-00

1/4-in. color camera, NTSC version, 22x zoom, high-resolution camera with

ExView technology, variable-speed camera dome, aluminum upper housing with

lower acrylic dome, mounting bracket not included

SVFT-MSH22C 8713-01

1/4-in. color camera, PAL version, 22x zoom, high-resolution camera with ExView

technology, variable-speed camera dome, aluminum upper housing with lower

acrylic dome, mounting bracket not included

SVFT-MSH18 8712-00

1/4-in. color camera, NTSC version, 18x zoom, high-resolution camera, variable-

speed camera dome, aluminum upper housing with lower acrylic dome, mounting

bracket not included

SVFT-MSH18C 8712-01

1/4-in. color camera, PAL version, 18x zoom, high-resolution camera, variable-

speed camera dome, aluminum upper housing with lower acrylic dome, mounting

bracket not included

For the ViconNet (V) option, add -20 to the product code; for Fiber Optic (F) option, add -30 to the product code;

for the Twisted Pair (T) option, add -40 to the product code.

Table 2

Models, Product Codes and Descriptions

Model Product

Code Description

SVFT-MSH-WM 8375-00 Wall Mount with Tamperproof Bit

SVFT-MSH-CM 8376-00 Ceiling Mount with Tamperproof Bit

S28PS 7029-00 28 VAC output, 2.5 amps, for indoor SurveyorVFT Camera Domes

V284-175PS 6421-00 Four channel, 120 VAC input, 28 VAC output, 7.25 amps

V288-360PS 6422-00 Eight channel, 120 VAC input, 28 VAC output, 13 amps

V2816-720PS 6423-00 Sixteen channel, 120 VAC input, 28 VAC output, 26 amps

Table 3

Optional Equipment Models, Product Codes and Descriptions

XX077-01-00 Rev 204 SVFT-MSH Maximum Security Housing Introduction •4

Figure 1

Exploded View

XX077-01-00 Rev 204 SVFT-MSH Maximum Security Housing Introduction •5

Installation

Mounting the Unit

The SVFT-MSH is intended for ceiling or wall installation using the optional Mounting Brackets. The primary

mounting surface must be a hard ceiling or wall able to support the weight of the entire assembly that is

approximately 30 lb (14 kg). It is recommended to use 3/8-in. (9.5-mm) diameter hardware. Mounting

hardware should consist of lag-type screws or bolts with accompanying lock and flat washers.

Also, be sure the area behind the selected location is clear of obstacles (such as steel beams, headers,

pipes, electrical wiring, etc.), which would interfere with mounting. Verify that there is access and sufficient

space behind the mounting location to route video and power cables and termination boxes. Refer to the

Cable Recommendations in the Reference section of this manual.

1. With the SVFT-MSH removed from the box and laid on a flat table, remove the Lower Dome Assembly by

uninstalling the nine (9) Tamperproof Screws. Use the provided Tamperproof Bit, located in the

Accessory Kit, for screw removal. Allow the Lower Dome Assembly to hang during installation.

2. Install the provided Liquid Tight Conduit Fitting, found in the Accessory Kit, into the Hole provided on back

of the Housing. Tighten the hex-mounting nut using an adjustable wrench until its snug.

3. Install the Mounting Bracket. There is either a Wall or Ceiling Mounting Bracket available. As previously

stated, it is recommended to use four 3/8-in. (9.5-mm)-diameter lag-type screws or bolts with lock and flat

washers. Choose one of the two available four (4) hole mounting patterns. Lift the Housing to the

Mounting Bracket and connect it using the four (4) pre-installed Tamperproof Screws. Use the

Tamperproof Bit provided with Mounting Bracket for installing screws.

4. Verify a maximum of 5 cables for power, video, communications, alarm and relay. Route the cables

through the Liquid Tight Conduit Fitting and leave about 12-in. (305-mm) length for connection to the

Customer Interface Board.

5. Unlatch the Customer Interface Board by pressing the latch and swinging it down about 90 degrees.

6. Remove the terminal blocks from the Accessory Kit. Cut and terminate all cables into the terminal blocks

in accordance with Tables 4, 5 and 6. All wired terminal blocks should easily reach their mating

connectors with the board re-latched. DO NOT APPLY POWER AT THIS TIME.

7. Install the terminal blocks into the Customer Interface Board, swing the board up and latch it into the

Housing.

Note: Vicon systems and components, like most electronic equipment, require a clean, stable power source.

Voltage irregularities such as surges, drops, and interruptions can affect the operation of your

equipment and, in severe cases, damage certain components. Vicon strongly recommends the use of

line conditioners, voltage regulators, and uninterruptible power supply (UPS) systems.

Caution: Be sure to make pin connections correctly. Wrong pin connections will cause damage to the unit.

XX077-01-00 Rev 204 SVFT-MSH Maximum Security Housing Installation •6

8. Configure communication and address DIP switches as shown on the label in Figure 2. For a detailed

description of DIP switch configuration, refer to the Configuration section of the SurveyorVFT Installation

& Operation Manual.

9. Lift the Camera Drive and connect it to the Housing by attaching the Safety Cable Clip to the Latch on the

Camera Drive.

10. Holding the Camera Drive under the housing, align the two slots on the Housing with the two tabs on the

Drive. While lining up the two arrows, push the Camera Drive into the Housing until it snaps securely into

place.

11. Attach Lower Dome using previously removed nine (9) Tamperproof Screws.

12. Installation is complete.

NNE

NUMBER

CONNECTOR TYPE CONNECTOR/PIN LABEL SIGNAL NAME

BNC (female) VIDEO (J1)

J1 VIDEO Video output

AMP Heade

J2 (Fiber Optic board)* Video/RS-422 data

TERMINAL BLOCK POWER (TB1)

TB1-1 HHot

TB1-2 NNeutral

TERMINAL BLOCK

LARM (TB2)

TB2-1 ALARM 1 Alarm input 1

TB2-2 GND Ground

TB2-3 ALARM 2 Alarm input 2

TB2-4 GND Ground

TB2-5 ALARM 3 Alarm input 3

TB2-6 GND Ground

TB2-7 ALARM 4 Alarm input 4

TB2-8 GND Ground

TERMINAL BLOCK COMM/RELAY (TB3)

TB3-1 COMM IN + Command in +

TB3-2 COMM IN - Command in -

TB3-3 RESP OUT + Response out +

TB3-4 RESP OUT - Response out -

TB3-5 GND Ground

TB3-6 RELAY C Relay, common

TB3-7 RELAY NO Relay, normally open

TB3-8 RELAY NC Relay, normally closed

*J2 connection provided to accommodate optional fiber optics interface board that provides video and

RS-422 full duplex data through a standard fiber optics connector.

Table 4

Electrical Connections – Coaxial/Fiber Optic Configurations

XX077-01-00 Rev 204 SVFT-MSH Maximum Security Housing Installation •7

NNE

NUMBER

CONNECTOR TYPE CONNECTOR/PIN LABEL SIGNAL NAME

TERMINAL BLOCK VIDEO NVT (TB4)

TB4-1 UTP + Unshielded twisted pair +

TB4-2 UTP - Unshielded twisted pair -

TB4-3 GND

TERMINAL BLOCK POWER (TB1)

TB1-1 HHot

TB1-2 NNeutral

TERMINAL BLOCK

LARM (TB2)

TB2-1 ALARM 1 Alarm input 1

TB2-2 GND Ground

TB2-3 ALARM 2 Alarm input 2

TB2-4 GND Ground

TB2-5 ALARM 3 Alarm input 3

TB2-6 GND Ground

TB2-7 ALARM 4 Alarm input 4

TB2-8 GND Ground

TERMINAL BLOCK COMM/RELAY (TB3)

TB3-1 COMM IN + Command in +

TB3-2 COMM IN - Command in -

TB3-3 RESP OUT+ Response out+

TB3-4 RESP OUT - Response out -

TB3-5 GND Ground

TB3-6 RELAY C Relay, common

TB3-7 RELAY NO Relay, normally open

TB3-8 RELAY NC Relay, normally closed

Table 5

Electrical Connections - UTP Configuration

XX077-01-00 Rev 204 SVFT-MSH Maximum Security Housing Installation •8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vicon Sicherheitskamera Handbücher

Vicon

Vicon V9360 Bedienungsanleitung

Vicon

Vicon Roughneck Pro V2000D Series Bedienungsanleitung

Vicon

Vicon VC-600 Series Bedienungsanleitung

Vicon

Vicon V992B-IR4 Bedienungsanleitung

Vicon

Vicon V2008-W0950-LPR Bedienungsanleitung

Vicon

Vicon Roughneck V894CSHR-VF-C Bedienungsanleitung

Vicon

Vicon XX264-20-00 Bedienungsanleitung

Vicon

Vicon Cruiser SN663V-A Betriebsanleitung

Vicon

Vicon HPOE-100 Bedienungsanleitung

Vicon

Vicon XX258-50-01 Roughneck Series Bedienungsanleitung

Vicon

Vicon ROUGHNECK V910V4 Bedienungsanleitung

Vicon

Vicon Roughneck V2000D-PTZ Bedienungsanleitung

Vicon

Vicon I-Onyx MPD-955 Bedienungsanleitung

Vicon

Vicon Surveyor 99 Betriebsanleitung

Vicon

Vicon Roughneck V910V3 Series Bedienungsanleitung

Vicon

Vicon VN-755IPV4 Bedienungsanleitung

Vicon

Vicon SurveyorVFT SVFT-C266M Bedienungsanleitung

Vicon

Vicon Cruiser SN673V-C Bedienungsanleitung

Vicon

Vicon Surveyor 2000 Bedienungsanleitung

Vicon

Vicon ROUGHNECK V-CELL-HD-B Bedienungsanleitung

Vicon

Vicon V960D-W Series Bedienungsanleitung

Vicon

Vicon V992D-N4 Gebrauchsanweisung

Vicon

Vicon Vantage V16 Bedienungsanleitung

Vicon

Vicon V922B-W551-A1 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung