WE-EF ETV100 LED Handbuch
Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Inground Luminaire
ETV100 LED
1
Inground Luminaire
ETV100
IP67, IK08. Class I. ta = 25°C
L
50
48
Product Dimensions:
ETV100 series L
ETV120 627
ETV130/ETV130-CC 927
ETV140/ETV140-CC 1227
Mounting Accessories:
Installation blockout Type I Type II
B = 160 mm B = 130 mm A
for 1 x ETV120 186-0306 186-0281 675
for 2 x ETV120 186-0307 186-0282 1304
for 3 x ETV120 186-0308 186-0283 1933
for 4 x ETV120 186-0309 186-0284 2562
for 1 x ETV130/ETV130-CC 186-0310 186-0285 975
for 2 x ETV130/ETV130-CC 186-0311 186-0286 1905
for 3 x ETV130/ETV130-CC 186-0312 186-0287 2833
for 4 x ETV130/ETV130-CC 186-0313 186-0288 3762
for 1 x ETV140/ETV140-CC 186-0314 186-0289 1275
for 2 x ETV140/ETV140-CC 186-0315 186-0290 2504
for 3 x ETV140/ETV140-CC 186-0316 186-0291 3733
for 4 x ETV140/ETV140-CC 186-0317 186-0292 4962
B
d:h
[A6] 1:10
[LA10] 1:5
2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
E\DVXLWDEO\TXDOLƂHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.
For operation with Tunable White, a DALI DT8 controller is required.
3
Installation
The product must be installed and maintained by a
VXLWDEO\TXDOLƂHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLƂHGE\DQ\ERG\RWKHU
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.
Attention: The luminaire is factory-sealed and does
not need to be opened during installation.
The installation on site must comply with local and/or
national health and safety regulations.
4
Blockout Installation Procedure
(during earth or masonry work)
1) Ensure that proper drainage is provided for
the shown installation methods:
a) In landscape/paved areas, sand or concrete
with gravel base (Fig. I).
b) With fully concreted installation, drainage
piping must be provided (Fig. II).
3) Test drainage (ensure water drains within
30 mins, Warning: warranty void if luminaire
installed without appropriate drainage)
2) Ensure a suitable recess.
Fig. II
Draining pipe
Fig. I
Fig. I
Fig. Il
4) Remove installation cover Aout of installation
blockout B.
5
5) Feed mains supply cable C(and second cable
Efor through wiring) through holes inside
blockout.
6) Replace blockout cover prior to luminaire
installation to prevent tripping hazard/
concrete dirt getting into blockout.
7) Blockout needs to get placed on an even, stable
DUHD7RSHGJHQHHGVWREHƃXVKZLWKVXUIDFH
Attention: ,IƃRRUZLOOEHWLOHGRUSDYHG
afterwards leave an appropriate gap. In case
luminaire gets installed at a later time, blockout
must get covered by installation cover A, to
make sure no concrete or dirt may enter
luminaire. Installation cover ensures that
blockout does not get damaged during masonry
works and needs to remain inside blockout until
installation of luminaire.
8) Framing should be installed to prevent vegeta-
tion from growing over the lens.
Frame
6
9) Switch off mains electrical supply.
12)Remove installation cover Afrom blockout B.11)Luminaire is pre-wired and LED included.
Opening the luminaire is not necessary.
Luminaire Installation Procedure
10)Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
ETV120 220-240V/50-60 Hz
186-XXXX SOE XXXXXXX
02/19 IP67
7
b) DALI (L = Phase, N = Neutral, = Earthing,
DA/DA = DALI control line, DA/DA = DALI
control line)
a) ON/OFF (L = Phase, N = Neutral,
= Earthing)
ø 7.5-16 mm for ON/OFF ø 6.5-12 mm for DALI
c) DMX: refer to separate TO9256W wiring instruction for hybrid DMX cable.
Attention:
a) To properly terminate and seal cables with sealable junction box, refer to information
packed with each sealable junction box G.
b) Cable sheaths must be contained within gel.
For operation with Tunable White, a DALI DT8 controller is required.
13)Take sealable junction box Gfrom its bag and open it.
Warning: Be careful to not get dirt inside the gel connector when opened and connecting mains
cable. Connect leads of luminaire cable Dand mains supply cable C (and second cable Efor through
wiring) to respective terminals in terminal connector F. Mains cables Cand Emust not cross to
ensure sealable junction box Gcan be properly closed.
8
15)Install spacers I. 16)To remove luminaire unfasten screws K out
of spacers I until you can grab their heads.
Insert lever Lbetween head of screws and
spacers. Lift spacers in an upwards direction.
14)Place sealable junction box Gand luminaire Hinside blockout. Make sure no cable is squeezed.
Attention: For [LA10] and [A6], ensure correct orientation of the luminaire.
Remove label before operation of luminaire.
we-ef
DIRECT LUMINAIRE TOWARDS WALL
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel +49 5194 909 0
Fax +49 5194 909 299
info.germany@we-ef.com
WE-EF LUMIERE
France
Tel +33 4 74 99 14 44
Fax +33 4 74 99 14 40
info.france@we-ef.com
WE-EF HELVETICA
Switzerland
Tel +41 22 752 49 94
Fax +41 22 752 49 74
info.switzerland@we-ef.com
WE-EF LIGHTING
Thailand
Tel +66 2 738 9610
Fax +66 2 175 2174
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
Tel +61 3 8587 0444
Fax +61 3 8587 0499
info.australia@we-ef.com
WE-EF LIGHTING
United States of America
Tel +1 724 742 0030
Fax +1 724 742 0035
info.usa@we-ef.com
TO9258W0321© WE-EF 2021
7HFKQLFDOVSHFLƂFDWLRQVDUH
subject to change.
Inhaltsverzeichnis
Andere WE-EF Außenleuchte Handbücher
WE-EF
WE-EF LSP400 LED Series Bedienungsanleitung
WE-EF
WE-EF LTC440 Bedienungsanleitung
WE-EF
WE-EF VFL500-SE Series Bedienungsanleitung
WE-EF
WE-EF ETC100 Series Bedienungsanleitung
WE-EF
WE-EF PFL230 LED Bedienungsanleitung
WE-EF
WE-EF FLA441 Technische Daten
WE-EF
WE-EF ZAT400 Series Bedienungsanleitung
WE-EF
WE-EF RMC320 LED Bedienungsanleitung
WE-EF
WE-EF VLR110 LED Bedienungsanleitung
WE-EF
WE-EF PFL540 LED Bedienungsanleitung
WE-EF
WE-EF FLA441 LED Bedienungsanleitung
WE-EF
WE-EF ETV100 Series Bedienungsanleitung
WE-EF
WE-EF PIA230 Bedienungsanleitung
WE-EF
WE-EF ASP500 Bedienungsanleitung
WE-EF
WE-EF QRO359 LED Bedienungsanleitung
WE-EF
WE-EF CTY150 Bedienungsanleitung
WE-EF
WE-EF ZA630 Bedienungsanleitung
WE-EF
WE-EF PFL230 Bedienungsanleitung
WE-EF
WE-EF DOC100 LED Series Bedienungsanleitung
WE-EF
WE-EF FLA780 Bedienungsanleitung
Beliebte Außenleuchte Handbücher anderer Marken
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung
urban ambiance
urban ambiance UQL1273 Bedienungsanleitung
TotalPond
TotalPond 52238 Bedienungsanleitung
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Bedienungsanleitung
LIGMAN
LIGMAN DE-20023 Bedienungsanleitung