Weider 8530 Bedienungsanleitung

USER’S MANUAL

Model No. WESY8530C2

Serial No.

Write the serial number in the space

above for reference.

CAUTION

Read all precautions and instruc-

tions in this manual before

using this equipment. Save this

manual for future reference.

www.weiderfitness.com

Visit our website at

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if there are

missing parts, please call:

1-888-936-4266

Mon.–Fri. 8h00 until 18h30 EST

(excluding holidays).

Serial Number

Decal

(Under Seat)

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

HOW TO USE THE HOME GYM SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

TROUBLESHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

CABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of

this manual. Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before

beginning assembly.

1. Read all instructions in this manual and in

the accompanying literature before using the

home gym system.

2. Use the home gym system only on a level

surface. Cover the floor beneath the home

gym system to protect the floor or carpet.

3. Inspect and properly tighten all parts often.

Replace any worn parts immediately.

4. Keep small children and pets away from the

home gym system at all times.

5. Always wear athletic shoes for foot protec-

tion.

6. Keep hands and feet away from moving

parts. Keep hands away from the squat arm

upright when the squat arm is being used.

Your hand could become pinched between

the squat arm upright and the squat arm.

7. Always stand on a foot plate when perform-

ing an exercise that could cause the home

gym system to tip.

8. Never release the press arm, butterfly arms,

squat arm, leg lever, lat bar or nylon strap

while weights are raised. The weights will fall

with great force.

9. Do not use the VKR station when either

weight stack is in use.

10. Make sure that the cables remain on the pul-

leys at all times. If the cables bind while you

are exercising, stop immediately and make

sure that the cables are on all of the pulleys.

11. Always disconnect the lat bar from the home

gym system when performing an exercise

that does not use the lat bar.

12. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-

ing down.

13. It is the responsibility of the owner to ensure

that all users of this home gym system are

adequately informed of all warnings and pre-

cautions.

WARNING: To reduce the risk of serious injury, read the following important precautions

before using the home gym system.

IMPORTANT PRECAUTIONS

WARNING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

BEFORE YOU BEGIN

ASSEMBLED

DIMENSIONS:

Height: 74 in.

Width: 60 in.

Length: 54 in.

Foot Plate

Low Pulley Station

High Pulley Station

Lat Bar

Leg Lever

Butterfly Arms

Squat Arm

Press Arm

Weight Stacks

Backrest

VKR Arms

Weight Pin

Thank you for selecting the versatile WEIDER®8530

home gym system. The WEIDER®8530 offers a selec-

tion of weight stations designed to develop every

major muscle group of the body. Whether your goal is

to tone your body, build dramatic muscle size and

strength, or improve your cardiovascular system, the

WEIDER®8530 will help you to achieve the specific

results you want.

For your benefit, read this manual carefully before

using the home gym system. If you have questions

after reading this manual, call our Customer Service

Department at 1-888-936-4266, Monday through

Friday, 8h00 until 18h00 Eastern Time (excluding holi-

days). To help us assist you, please note the product

model number and serial number before calling. The

model number is WESY8530C2. The serial number

can be found on a decal attached to the home gym

system (see the front cover of this manual).

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

ASSEMBLY

High

Side

1. Before beginning assembly, be sure that

you have read and understand the infor-

mation in the box above.

Press a 2” Inner Cap (27) into the indicated

end of the Stabilizer (5). Press 2” Outer

Caps (51) onto the other two locations on

the Stabilizer. Press a 2” Inner Cap into the

end of the Base (4).

Insert four 5/16” x 2 1/2” Carriage Bolts (1)

up through the Stabilizer (5).

Attach the Base (4) to the Stabilizer (5) with

two 5/16” x 2 3/4” Bolts (11), two 5/16” Flat

Washers (8), and two 5/16” Nylon Locknuts

(3). Do not tighten the Nylon Locknuts

yet.

Slide the VKR Upright (74) and the Squat

Arm Upright (56) onto the 5/16” x 2 1/2”

Carriage Bolts (1) in the Stabilizer (5). The

high side of the brackets on the VKR

Upright and Squat Arm Upright should be

on the side shown. Hand-tighten four 5/16”

Nylon Locknuts (3) onto the Carriage Bolts.

Do not tighten the Nylon Locknuts yet.

FRAME ASSEMBLY

Before beginning assembly, carefully read the

following information and instructions:

•Place all parts of the home gym system in a

cleared area and remove the packing materials;

do not dispose of the packing materials until

assembly is completed.

• Assembly is divided into five stages: 1) frame

assembly, 2) press and butterfly arm assembly,

3) cable and pulley assembly, 4) seat and back-

rest assembly, and 5) VKR assembly. The hard-

ware for each stage is packaged separately.

• Wait until you begin each assembly stage to open

the parts bag labeled for that assembly stage.

•For help identifying the small parts used in

assembly, use the PART IDENTIFICATION

CHART located in the center of this manual.

Note: Some small parts may have been pre-

attached for shipping. If a part is not in the parts

bag, check to see if it has been pre-attached.

•As you assemble the home gym system, be sure

that all parts are oriented as shown in the draw-

ings.

•Tighten all parts as you assemble them, unless

instructed to do otherwise.

THE FOLLOWING TOOLS (NOT INCLUDED) ARE

REQUIRED FOR ASSEMBLY:

• Two adjustable wrenches

• One standard screwdriver

• One phillips screwdriver

• One rubber mallet

• Lubricant, such as grease or petroleum jelly,

and soapy water will also be needed.

Assembly will be more convenient if you have the

following tools: A socket set, a set of open-end or

closed-end wrenches, or a set of ratchet wrenches.

2. Insert two 5/16” x 2 1/2” Carriage Bolts (1) up

through the Base (4).

Slide the Front Upright (42) onto the 5/16” x

2 1/2” Carriage Bolts (1) in the Base (4).

Hand-tighten a 5/16” Nylon Locknut (3) onto

each Carriage Bolt. Do not tighten the

Nylon Locknuts yet.

Press a 1” Inner Cap (6) into the Front

Upright (42). Press a 2” Inner Cap (27) into

the Squat Upright (56). Press a 2” Inner Cap

into the VKR Upright (74).

3. Press a 2” Inner Cap (27) into the end of the

Top Frame (55). Press a 1 3/4” Inner Cap

(44) into each end of the crossbar on the Top

Frame. Press two Inner Caps (96) into the top

of the crossbar.

Attach the Top Frame (55) to the Front

Upright (42) with two 5/16” x 2 3/4” Bolts (11),

two 5/16” Flat Washers (8), and two 5/16”

Nylon Locknuts (3).

Attach the Top Frame (55) to the VKR Upright

(74) and the Squat Upright (56) with two 5/16”

x 2 3/4” Bolts (11) and two 5/16” Nylon

Locknuts (3).

Tighten all of the 5/16” Nylon Locknuts (3)

used in steps 1–3.

4. Set two Weight Bumpers (19) on the bracket

on the Base (4) as shown. Set two Weight

Bumpers (19) on the bracket on the Stabilizer

(5).

Stack eight Weights (25) onto each set of

Weight Bumpers (19). Be sure that the pin

grooves are all on the same side of each

stack of Weights.

Be careful not to tip either stack of

Weights (25) until step 6 is complete.

FRAME ASSEMBLY

27 55 3

896

Crossbar

5—Bracket

Grooves

4—Bracket

5. Press a Weight Tube Bumper (64) into the

end of a Weight Tube (63). Insert the Weight

Tube into the front stack of Weights (25). Be

sure that the pins on the Weight Tube are

sitting in the pin grooves in the top

Weight.

Lubricate the inside of the holes in a Top

Weight (65). Set the Top Weight onto the front

stack of Weights (25). Insert both Long

Weight Guides (62) into the stack of Weights.

Be sure that the holes in the Weight

Guides are at the top, as shown.

6. Press a Weight Tube Bumper (64) into the

end of the other Weight Tube (63). Insert the

Weight Tube into the rear stack of Weights

(25). Be sure that the pins on the Weight

Tube are sitting in the pin grooves in the

top Weight.

Lubricate the inside of the holes in the other

Top Weight (65). Set the Top Weight onto the

rear stack of Weights (25). Insert both Short

Weight Guides (73) into the stack of Weights.

Be sure that the holes in the Weight

Guides are at the top, as shown.

FRAME ASSEMBLY

Holes

Lubricate

Holes

64 25

7. Attach the upper ends of the Long Weight

Guides (62) to the Top Frame (55) with a

5/16” x 6” Bolt (60), two 1/2” x 3/4” Spacers

(61), and a 5/16” Nylon Locknut (3).

Be sure that the Pulley Bracket (20) is in

front of the right Long Weight Guide (62)

as shown.

Attach the upper ends of the Short Weight

Guides (73) to the Top Frame (55) with a

5/16” x 6” Bolt (60), two 1/2” x 3/4” Spacers

(61), and a 5/16” Nylon Locknut (3).

8. Press a 1” x 7/8” Plastic Bushing (90) onto

each welded spacer on the Press Frame (17).

Slide the Press Frame into place onto the

Base (4). Note: This will be a tight fit. The

Plastic Bushings should fit on each end of

the indicated tube in the Base. Make sure

that the pulleys are on the side shown.

Lubricate the 3/8” x 8” Bolt (59). Attach the

Press Frame (17) to the Base (4) with the

3/8” x 8” Bolt and a 3/8” Nylon Locknut (21).

9. Wet the handle of one Press Arm (46) with

soapy water. Slide a 5” Plastic Grip (83) onto

the handle. Press a 1” Round Inner Cap (49)

into the other end of the handle. Press a

1 3/4” Inner Cap (44) into the Press Arm.

Attach the Press Arm (46) to one side of the

Press Frame (17) with two 5/16” x 2 1/2”

Bolts (22) and two 5/16” Nylon Locknuts (3).

Assemble the other Press Arm (46) in the

same manner.

10. Identify the Right Arm (48) and the Left Arm

(47). Note the position of the welded bracket

on each Arm. Arm identification is very

important for step 11.

Attach a “V”-Pulley (50) and a Long Cable

Trap (31) to the Right Arm (48) with a 3/8” x

2 1/2” Bolt (86) and a 3/8” Nylon Locknut

(21).

Attach a “V”-Pulley (50) and a Long Cable

Trap (31) to the Left Arm (47) in the same

manner.

ARM ASSEMBLYFRAME ASSEMBLY

61 361

73 62

17 59

Lubricate

4—Tube

Welded

Spacers

Handle

Welded

Bracket

11. Lubricate both axles on the Top Frame (55).

Slide the Right Arm (48) onto the right axle.

Be careful not to confuse the Right Arm

with the Left Arm (47); note the position of

the “V” Pulley (50) to identify the Right

Arm. Be sure that the upper end of the

Right Arm is behind the indicated bracket

on the Top Frame (55).

Tap two 1” Retainers (69) and a 1” Round

Cover Cap (70) onto the axle. Be sure that

the teeth on the Retainers bend toward the

Round Cover Cap, as shown in the inset

drawing.

Attach the Left Arm (47) in the same manner.

Press 1 3/4” Inner Caps (44) into the lower

ends of the Left and Right Arms (47, 48). Wet

the lower end of each Arm with soapy water.

Slide a 10” Pad (45) onto the lower end of

each Arm.

12. Press two 1” x 2” Inner Caps (87) into the

indicated end of the Squat Arm (84).

Attach the Squat Arm (84) to the VKR Upright

(74) with a 3/8” x 5 1/2” Bolt (93) and a 3/8”

Nylon Locknut (21). Be sure that the indicat-

ed bracket is pointing down as shown.

Wet the ends of the Squat Arm (84) with

soapy water. Slide the two Squat Arm Pads

(85) onto the Squat Arm.

Attach a Handle (82) to one side of the Squat

Arm (84) with a 5/16” x 2 1/2” Bolt (22), two

5/16” Flat Washers (8), a 1/2” x 17/32” Spacer

(91), and a 5/16” Nylon Locknut (3).

Wet the Handle (82) with soapy water. Slide a

5” Plastic Grip (83) onto the Handle. Press a

1” Round Inner Cap (49) into the other end of

the Handle.

Assemble another Handle (82) to the other

side of the Squat Arm (84) in the same man-

ner.

ARM ASSEMBLY

83 82

22 85

849

Bracket

Axle—

Lubricate

55—Axle

Bracket

During steps 13 to 25, refer to the CABLE DIA-

GRAM on page 19 of this manual. Identify the

three cables by their lengths, and note the

positions of the cable traps. IMPORTANT: Do

not overtighten the bolts and nuts securing

the pulleys. The pulleys must turn freely.

13. Locate the Medium Cable (58). Route the

Medium Cable around the indicated 3 1/2”

Pulley (15) attached to the Top Frame (55).

Be sure that the ball is on the indicated

side of the Pulley and that the Cable is

between the Pulley and the hook. Tighten

the 3/8” x 3 3/4” Bolt (88) and the 3/8” Nylon

Locknut (not shown).

14. Wrap the Medium Cable (58) around a “V”-

Pulley (50). Attach the “V”-Pulley and a Long

Cable Trap (31) to the indicated bracket on

the Front Upright (42) with a 3/8” x 2 1/2” Bolt

(86) and a 3/8” Nylon Locknut (21). Be sure

that the Long Cable Trap is positioned to

hold the Cable in place.

Route the Medium Cable (58) around the “V”-

Pulley (50) on the Left Arm (47). Be sure that

the Cable is in the groove of the Pulley and

that the Long Cable Trap (31) holds the

Cable in place. Tighten the 3/8” x 2 1/2” Bolt

(86) and the 3/8” Nylon Locknut (not shown).

15. Route the Medium Cable (58) around the “V”-

Pulley (50) on the Right Arm (48). Be sure

that the Cable is in the groove of the “V”-

Pulley and that the Long Cable Trap (31) is

positioned to hold the Cable in place.

Tighten the 3/8” x 2 1/2” Bolt (86) and the 3/8”

Nylon Locknut (not shown).

Route the Medium Cable (58) around the

3 1/2” Pulley (15) attached to the Pulley

Bracket (20). Be sure that the Cable is in

the groove of the Pulley and that the Cable

Trap (66) holds the Cable in place. Tighten

the 3/8” Nylon Locknut (21) and the 3/8” x 2”

Bolt (not shown). Tighten the 5/16" x 5” Bolt

(68) and the 5/16" Nylon Locknut (not shown).

Be sure that the Pulley Bracket swivels freely.

16. See the inset drawing. Attach a 3 1/2” Pulley

(15) and a Cable Trap (66) to the upper hole

in the Long “U”-Bracket (57) with a 3/8” x 2”

Bolt (12) and a 3/8” Nylon Locknut (21). Be

sure that the Cable Trap is inside the Long

“U”-Bracket. (Note: This may come pre-

assembled.)

Route the Medium Cable (58) through the

3 1/2” Pulley (15) and Long “U”-Bracket (57)

shown in the inset drawing. Be sure that the

Cable is in the groove of the Pulley and

that the Cable and Pulley move smoothly.

CABLE ASSEMBLY

15 88

Ball

86 50

Bracket

58 58

Hook

Andere Handbücher für 8530

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weider Heim-Fitnessstudio Handbücher

Weider

Weider 9350hard Drive Sys Bedienungsanleitung

Weider

Weider Pro 330 Bench Bedienungsanleitung

Weider

Weider 325 Bench Systemhandbuch

Weider

Weider 9025 Bedienungsanleitung

Weider

Weider WEBE11880 Bedienungsanleitung

Weider

Weider 9250 Kurzanleitung

Weider

Weider 8925hard Drive Sys Bedienungsanleitung

Weider

Weider WESY13820 Bedienungsanleitung

Weider

Weider 150722 Bedienungsanleitung

Weider

Weider Pro 290 wc bench Bedienungs- und Wartungshandbuch

Weider

Weider WECCSY24540 Bedienungsanleitung

Weider

Weider Body Works Pro 2.0 Bench Systemhandbuch

Weider

Weider Flex 225 Bedienungsanleitung

Weider

Weider Platinum Plus 1000 Bedienungsanleitung

Weider

Weider 9250 Benutzerhandbuch

Weider

Weider Pro 215 Bench Bedienungsanleitung

Weider

Weider B101 Bench Bedienungsanleitung

Weider

Weider 831.159010 Bedienungsanleitung

Weider

Weider WESY81081 Bedienungsanleitung

Weider

Weider Body Works Pro 2.0 Bench Kurzanleitung

Weider

Weider Pro 120 Bench Benutzerhandbuch

Weider

Weider Platinum WECCSY78740 Bedienungsanleitung

Weider

Weider WESY5983.5 Bedienungsanleitung

Weider

Weider 831.150380 Bedienungsanleitung

Beliebte Heim-Fitnessstudio Handbücher anderer Marken

Horizon Fitness

Horizon Fitness OXFORD 6 Bedienungsanleitung

Energetics

Energetics Multi Trainer 5.1 Bedienungsanleitung

Matrix

Matrix MG-PL Series Bedienungsanleitung

Reebok

Reebok Tbr2i Bedienungs- und Wartungshandbuch

Pure Fitness

Pure Fitness 8526HE Bedienungsanleitung

Bowflex

Bowflex Sport 001-6961 Bedienungsanleitung

NordicTrack

NordicTrack E8200 Competition Bench Kurzanleitung

Body Solid

Body Solid GHYP-345 Bedienungsanleitung

Evo

Evo TAHOE 5105 Bedienungsanleitung

cardiobull

cardiobull RA17 Bedienungsanleitung

ParaBody

ParaBody 40 Bedienungsanleitung

JLL

JLL Ventus Pro Air Power Bedienungsanleitung

Trojan

Trojan Colorado 370 Bedienungsanleitung

Octane Fitness

Octane Fitness xRide xR650 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung

Insportline

Insportline RW600 Bedienungsanleitung

Stamina

Stamina 55-1532 Bedienungsanleitung

Tunturi

Tunturi R25 Bedienungsanleitung