Weider Platinum Plus 1000 Bedienungsanleitung

CAUTION

Read all precautions and instruc-

tions in this manual before

using this equipment. Save this

manual for future reference.

QUESTIONS?

As a manufacturer,we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if a part is

damaged or missing, PLEASE

CONTACT OUR CUSTOMER

SERVICE DEPARTMENT

DIRECTLY.

CALL TOLL-FREE:

1-877-992-5999

Mon.–Fri., 6 a.m.–6 p.m. MST

ON THE WEB:

www.weiderservice.com

Serial Number Decal (under seat)

Model No. WESY9975.0

Serial No.

Write the serial number in the

space above for future reference.

Visit our website at

www.weiderfitness.com

new products, prizes,

fitness tips, and much more!

USER’S MANUAL

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

CONSOLE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of

this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before begin-

ning assembly.

WEIDER is a registered trademark of ICON IP

,Inc.

TABLE OF CONTENTS

WARNING DECAL PLACEMENT

The decals shown here have been

placed on the resistance system. If a

decal is missing or illegible, please call

the toll-free telephone number on the

front cover of this manual and order a

free replacement decal. Apply the decal

in the location shown.

Keep hands and

fingers clear of

this area.

1. Read all instructions in this manual and all

warnings on the resistance system before

using the resistance system. Use the resist-

ance system only as described in this manual.

2. It is the responsibility of the owner to ensure

that all users of the resistance system are

adequately informed of all precautions.

3. The resistance system is intended for home

use only. Do not use the resistance system in

any commercial, rental, or institutional setting.

4. Keep the resistance system indoors, away

from moisture and dust. Place the resistance

system on a level surface, with a mat

beneath it to protect the floor or carpet. Make

sure that there is enough clearance around

the resistance system to mount, dismount,

and use the resistance system.

5. Inspect and properly tighten all parts regular-

ly. Replace any worn parts immediately.

6. Keep children under 12 and pets away from

the resistance system at all times.

7. Keep hands and feet away from moving parts.

8. Always wear athletic shoes for foot protec-

tion while exercising.

9. The resistance system is designed to sup-

port a maximum user weight of 300 pounds.

10. The top frame is not designed to be used for

pull-up exercises. Do not hang on the top

frame.

11. Pull on the lower cable only while sitting on

the bench or standing on the base plate. Pull

on the high cables only while sitting on the

bench, with the seat in one of the three posi-

tions closest to the upright base, or while

standing on the base plate.

12. The resistance system is designed to be

used with the included resistance. Do not

use the resistance system with any other

type of resistance.

13. Always disconnect the lat bar from the high

cables when performing an exercise that

does not require it.

14. Make sure the storage knob is in place and

fully tightened each time the resistance sys-

tem is used.

15. Make sure that the cables remain on the pul-

leys at all times. If the cables bind as you are

exercising, stop immediately and make sure

that the cables are on the pulleys. Replace all

cables at least every two years.

16. Always make sure the two screws in the rope

clamps are fully tightened each time the

resistance system is used.

17. Do not pull on the cables while the resist-

ance level is being adjusted.

18. If you feel pain or dizziness while exercising,

stop immediately and begin cooling down.

WARNING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

WARNING: To reduce the risk of serious injury, read the following important precautions

before using the resistance system.

IMPORTANT PRECAUTIONS

High Pulley

Squat Arm

Backrest

Storage Knob

Squat Backrest

Handle

Console

Top Frame

Low Pulley

Base Plate

Leg Lever

Mat

Curl Pad

Curl Bar

Seat

Squat Pin

Seat Knob

BEFORE YOU BEGIN

Thank you for selecting the innovative PLATINUM

PLUS 1000 BY WEIDER®resistance system. The

resistance system offers a selection of stations

designed to develop every major muscle group of the

body. Whether your goal is to tone your body, build dra-

matic muscle size and strength, or improve your cardio-

vascular system, the resistance system will help you to

achieve the specific results you want.

For your benefit, read this manual carefully before

using the resistance system. If you have questions

after reading this manual, see the front cover of this

manual. To help us assist you, please note the product

model number and serial number before calling. The

model number is WESY9975.0. The serial number can

befound on a decal attached to the resistance system

(see the front cover of this manual).

To avoid a registration fee for any service needed

under warranty, you must register the weight sys-

tem at www.weiderservice.com/registration.

Before reading further, please review the drawing below

and familiarize yourself with the parts that are labeled.

ASSEMBLED DIMENSIONS:

Height: 85 in. / 216 cm

Width: 47 in. / 119 cm

Depth: 94 in. / 239 cm

Before beginning assembly, carefully read the

following information and instructions:

•Assembly requires two persons.

•Place all parts in a cleared area and remove the

packing materials. Do not dispose of the packing

materials until assembly is completed.

•

For help identifying small parts, use the PART

IDENTIFICATION CHART.

Note: Some small

parts may have been pre-attached for shipping. If

apart is not in the parts bag, check to see if it

has been pre-attached.

•Tighten all parts as you assemble them, unless

instructed to do otherwise.

•Asyou assemble the resistance system, make

sure all parts are oriented as shown in the draw-

ings.

The included hex keys and the following

tools (not included) are required for assembly:

• Two adjustable wrenches

• One rubber mallet

• One standard screwdriver

• One Phillips screwdriver

• Lubricant, such as grease or petroleum jelly,

tape, and soapy water.

Assembly will be more convenient if you have a

socket set, a set of open-end or closed-end

wrenches, or a set of ratchet wrenches.

Make Things Easier for Yourself

This manual is designed to ensure that the resist-

ance system can be assembled successfully by

most people. However, it is important to realize

that the versatile resistance system has many

parts and that the assembly process will take

time. Most people find that by setting aside plenty

of time, assembly will go smoothly.

ASSEMBLY

Attach four Plastic Base Feet (71) to the Base (1)

with four M4 Washers (157) and four M4 x 16mm

Self-tapping Screws (104).

Attach a Wheel (49) to the Base (1) with an M8 x

90mm Shoulder Bolt (125), two M8 Washers

(152), and an M8 Nylon Jamnut (139). Repeat

with the other Wheel.

Before beginning assembly,make sure that

you have read and understand the informa-

tion in the box above. Refer to the PART

IDENTIFICATION CHART for help identifying

small parts.

104

157

104

139

152 152

125

157

104

157

104

157

2. Insert two M10 x 65mm Carriage Bolts (103) up

through the Base (1). Place a piece of tape over

the Bolt heads to hold them in place. Connect

the Upright Base (2) to the Base with the two

Carriage Bolts and two M10 Nylon Locknuts

(112). Do not tighten these Locknuts yet.

Connect the Upright Base (2) to the Base (1) with

two M10 x 67mm Bolts (111) and two M10 Nylon

Locknuts (112). Fully tighten these Locknuts.

Set the Mech Frame (124) onto the Base (1)

behind the Upright Base. Handtighten two M10 x

73mm Bolts (137) and two M10 Washers (129)

into the indicated holes in the Base and Mech

Frame. Note: The Mech Frame will not be

shown in the following drawings for clarity.

Note: One end of the Rope (70) is connected

to the Right Arm Frame (171). Untie the loose

end of the Rope and route it through the Upright

Base (2). Make sure the Rope is still between

the 90mm Thin Pulley (88) and Cable Trap (78)

(see the inset drawing), and that the loose end

of the Rope crosses under the connected end

of the Rope.

Insert two M14 x 155mm Bolts (107) through the

Right Arm Frame (171) and the Upright Base (2).

Hand tighten two M14 Nylon Locknuts (127) onto

the Bolts.

3. Route the loose end of the Rope (70) through the

Left Arm Frame (8) and a Swivel Arm (29). Make

sure the Rope is under the indicated rod in the

Swivel Arm.

Attach the Swivel Arm (29) to the Left Arm Frame

(8) with an M4 x 5mm Self-tapping Screw (176).

Attach a “V”-pulley (93) inside the Swivel Arm

(29) with an M10 x 53mm Button Bolt (140) and

an M10 Nylon Locknut (112).

171

107

112

127

112

111

124

129

137

129

137

103

176

140

112

Rod

169

166

Large

Hole

165

4. Route the loose end of the Rope (70) through a

Rope Cover (169) and a Link (167) as shown.

Make sure the large hole in the Rope Cover is

on the side shown. Secure the set of Rope

Clamps (165, 166) on the Rope with two M5 x

16mm Button Screws (164). Make sure that

Rope is in the grooves of the Rope Clamps,

that there is 1/2" between the Link and the

Rope Clamps, and that the two Screws are fully

tightened. Slide the Rope Cover over the Rope

Clamps.

167

164

6. Attach the Backing Plate (59) to the Upright Base

(2) with two M10 x 65mm Carriage Bolts (103)

and two M10 Nylon Locknuts (112). Do not tight-

en the Locknuts yet.

103 112

5. Remove the two M14 Nylon Locknuts (127).

Attach the Left Arm Frame (8) to the Upright Base

(2) with the two M14 x 155mm Bolts (107) used in

step 2 and the two M14 Nylon Locknuts.

127

107

7. Attach the Squat Backrest (28) to the Squat

Carriage (10) with four M6 x 16mm Screws (108).

108

105

129

159

172

172 173

9. Press the Front Cover (31) onto the Upright Base

(2). Make sure the Cover is oriented as shown

in the inset drawing.

Route the Upper Wire Harness (172) down

through the Upright Base (2) and out the large

round hole in the back, as shown.

Slide the Upright (3) onto the Upright Base (2).

Make sure you do not pinch the Upper Wire

Harnesses (172). Secure the Upright with two

M10 Washers (129), two M10 x 20mm Screws

(113), and two M10 x 25mm Screws (105). Do

not tighten the Screws yet.

Connect the Upper Wire Harness (172) to the

Lower Wire Harness (173) extending from the

Mech Frame (not shown). The connector should

slide easily into the socket and snap into place.

If the connector does not slide easily and snap into

place, turn it over and then insert it. IF THE CON-

NECTOR IS NOT INSERTED PROPERLY, THE

CONSOLE MAY BE DAMAGED WHEN THE

POWER IS TURNED ON. Press the excess wire

into the Upright Base.

Tighten two M4 x 16mm White ZP Self-tapping

Screws (159) into the Upright (3).

113

8. Slide the Squat Carriage (10) onto the Upright (3)

as shown. Insert the Squat Pin (35) into an upper

hole in the Upright.

159

129

124

1137

137

129

144

129

137

10. Insert an M10 x 125mm Button Screw (144)

through an M10 Washer (129), the Upright (3),

and the Backing Plate (not shown). Hold the Bolt

in place by sticking a piece of tape over the

bolt head.

Tighten the two M10 Nylon Locknuts (112)

used in step 6. Tighten the two M10 x 20mm

Screws (113) and two M10 x 25mm Screws

(105) used in step 9.

Attach the Mech Frame (124) to the Base (1) with

two M10 x 73mm Bolts (137) and two M10

Washers (129). Do not tighten the Bolts yet.

Attach the Mech Frame (124) to the Upright (3)

with the M10 x 125mm Button Screw (144). Make

sure the Upright and Mech Frame are properly

aligned before tighten the Screw.

Tighten the four M10 x 73mm Bolts (137) in

the Base (1) and the two M10 Nylon Locknuts

(112) used in the first paragraph of step 2.

173

183

196

173

11. Locate the Lower Wire Harness (173) (see the

inset drawing). Connect the Lower Wire Harness

to the Sensor (196). The connector should slide

easily into the socket and snap into place. If the

connector does not slide easily and snap into place,

turn the connector over and then insert it. IF THE

CONNECTOR IS NOT INSERTED PROPERLY,

THE CONSOLE MAY BE DAMAGED WHEN

THE POWER IS TURNED ON.

Snap the Sensor Plate (183) into the Side Mech

Cover (81).

12. Snap the Side Mech Cover (81) into place on the

Mech Covers (14 and 15).

15 14

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weider Heim-Fitnessstudio Handbücher

Weider

Weider Esb5 Slant Board Bedienungsanleitung

Weider

Weider Gold MEDALLION M4744 Bedienungsanleitung

Weider

Weider 215 Bench Bedienungsanleitung

Weider

Weider Stepmaster SM6 Bedienungsanleitung

Weider

Weider Clubstepper SM10 Bedienungsanleitung

Weider

Weider 245 Bench Bedienungsanleitung

Weider

Weider WEMC07730 Bedienungsanleitung

Weider

Weider 8220hard Drive Sys Bedienungsanleitung

Weider

Weider Power Tower WEBE99712.0 Bedienungsanleitung

Weider

Weider 190 T Bench Bedienungsanleitung

Weider

Weider 8700 I Bedienungsanleitung

Weider

Weider FLEX-CTS WESY20318.0 Bedienungsanleitung

Weider

Weider 831.153972 Bedienungsanleitung

Weider

Weider Flex Ctx 60 Bedienungsanleitung

Weider

Weider Silver Medallion2uprt Be Bedienungsanleitung

Weider

Weider PRO 635 Bedienungsanleitung

Weider

Weider 214 Bench Kurzanleitung

Weider

Weider CORe 600 831.15715.0 Bedienungsanleitung

Weider

Weider WESY3873.2 Bedienungsanleitung

Weider

Weider 7000x-train Bedienungsanleitung

Weider

Weider 4990 I Bedienungsanleitung

Weider

Weider 340 Lc Bench Systemhandbuch

Weider

Weider 4990 I Systemhandbuch

Weider

Weider 9015 Bedienungsanleitung

Beliebte Heim-Fitnessstudio Handbücher anderer Marken

Horizon Fitness

Horizon Fitness OXFORD 6 Bedienungsanleitung

Energetics

Energetics Multi Trainer 5.1 Bedienungsanleitung

Matrix

Matrix MG-PL Series Bedienungsanleitung

Reebok

Reebok Tbr2i Bedienungs- und Wartungshandbuch

Pure Fitness

Pure Fitness 8526HE Bedienungsanleitung

Bowflex

Bowflex Sport 001-6961 Bedienungsanleitung

NordicTrack

NordicTrack E8200 Competition Bench Kurzanleitung

Body Solid

Body Solid GHYP-345 Bedienungsanleitung

Evo

Evo TAHOE 5105 Bedienungsanleitung

ParaBody

ParaBody 40 Bedienungsanleitung

JLL

JLL Ventus Pro Air Power Bedienungsanleitung

Trojan

Trojan Colorado 370 Bedienungsanleitung

Octane Fitness

Octane Fitness xRide xR650 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung

Insportline

Insportline RW600 Bedienungsanleitung

Stamina

Stamina 55-1532 Bedienungsanleitung

Tunturi

Tunturi R25 Bedienungsanleitung

CYBEX

CYBEX Jungle Gym 17000 Bedienungsanleitung