Zeiss Cell Observer spinning disk confocal Bedienungsanleitung

Page | 1

Wellcome Trust Centre for Human Genetics

Cellular-Imaging Microscopy Core

The Zeiss Spinning Disk

Confocal

Abridged INSTRUCTIONS

Page | 2

Introduction

The Zeiss Cell Observer spinning disk confocal microscope is located in the

category three viral suite in the Oxford Particle Imaging Centre (STRUBI). The

spinning disk’s principle advantage over our Leica SP8 and Zeiss 510 LSM

microscopes is speed of acquisition rather than image quality, and so the

spinning disk is particularly suited to live cell imaging, although it can image

specimens on slides as well.

The new Zeiss Cell Observer spinning disk confocal microscope has:

•Zeiss Observer Z1 Inverted Microscope

•NewPort Vision IsoStation anti-vibration isolation table

•Yokogawa CSU-X1 Filter Wheel and Spinning Disk Unit

•Photometrics Evolve 512 Delta EM-CCD camera (512 x 512 pixels)

•Applied Scientific MS2000 Piezo motorised XY stage

•Applied Scientific fast galvo Z focus (150um range)

•Definite Focus with NIR LED Hardware Focus to eliminate thermal drift

•PeCon Temp Module S1 and XL Multi S1 live cell stage incubator

(rated 3oC to 45oC)

•10x EC Plan Neofluar NA 0.3 air objective

•40x C-Apochromat NA 1.2 water-immersion objective (with coverslip

correction collar)

•63x C-Apochromat NA 1.2 UV-VIS-IR water-immersion objective (with

coverslip correction collar)

•100x Plan Apochromat NA 1.4 oil-immersion objective

•Zeiss HXP-120V short-arc fluorescence Hg lamp and controller (2,000h)

•DAPI, GFP and DSRed diochroic filters for eyepiece viewing

•405nm line DAPI laser

•480nm line GFP and 468nm line DsRed laser

•Zeiss ZEN Blue image aquisition software

Page | 3

General information

The system can only image green GFP/FITC, red DsRed/RFP/TexsRed and blue

DAPI dyes. As well as single dichroics, we have a double GFP/DS-Red for faster

imaging of these two dyes. We don’t have the optional Cy5 far red laser.

The Photometrics Evolve 512 Delta EM-CCD camera has a maximum resolution

of 512 x 512 pixels. It captures black and white images with a 16-bit depth of

65,536 grey levels (with 0 being pure black- and 65,535 being pure white).

The Evolve camera’s fastest frame rate is 15ms (67 frames per second). Images

are stored in the Zeiss *.czi format. To view these *.czi files on another

Windows 7 PC download Zen Lite via the Core’s Spinning Disk microscope

webpages.

All scans by Zeiss’s Zen Blue image acquisition software are automatically

saved in ‘My Pictures/Temp’ on the PC, but will be deleted when you leave Zen

(so save them first). In event of Zen crashing or PC mains failure the files will

remain in Temp.

Use ‘snap’ in Zen Blue to clear noise from the camera detectors before

imaging. Setting ‘snap’ for every image will slow down acquisition a lot, but

you can just ‘snap’ clear at the beginning of an image sequence. Adjust

exposure time, laser power and EM Gain for brightness in ‘Acquisition’.

Don’t go above 300 in EM Gain with the camera (there’s not safety warning).

The EM Gain going from 1 to 200 goes from the equivalent of ½ second to a

20ms to frame rate. Avoid putting too much light onto the cameras EMCCD

sensor. The Evolve camera needs to be triggered if you want extra speed.

Click Live for faster ‘preview’ imaging with more noise.

Smart setup for selecting fluorochromes (Channels) starts the laser power at

50% which will be too high for most samples. Fixed samples seem to bleach

very rapidly at these higher laser powers.

You can save configurations and the menu screen setup. You can reuse

microscope and camera settings from a stored image.

Page | 4

Using the Zeiss Observer Z1 microscope

The Cell Observer microscope mixes air (10x), oil (100x), and water objectives

(40x and 63x). Make sure you use the appropriate immersion fluid with the

objective. The immersion oil for the 100x oil is left on the air table and the

Immersol W 2010 for water immersion is left under the PC monitor. The two

immersion fluids don’t mix. The Immersol water immersion fluid is particularly

prone to drips from the applicator so take care when using it not to overload

the applicator (if oil or water Immersol drips from its applicator you are using

too much).

It is far easier to control the DAPI, GFP and DsRed mercury lamp fluorescence

(as viewed down the eyepieces) from the PC’s Zen Blue software.

Alcohol 70% is provided along with gloves and green-box lab tissues. These are

supplied for cleaning the samples and spillages and are not to be used on the

objectives. Be careful where you stand the 70% alcohol bottle as the alcohol

can drip out from the spout into electronics.

Only Whatman 105 Lens Cleaning tissues are to be used to wipe oil and

Immserol water fluid from the objectives.

We don’t have the Tile module for the confocal system, so we can only raster

scan and stitch images around one single field. We can time-lapse at multiple

locations though (but it must be with the same dye filter configuration at each

location).

Page | 5

Using the Zeiss Observer XL stage incubator

The Zeiss 37oC incubator controller must be switched on before any other

equipment otherwise the control link to the microscope stand won’t be

established and ‘Incubation’ will not appear as a tab in the Observer Z1’s LCD

controller.

To switch on the Temp Controller press its rear rocker switch to the left (the

lowest LED lights up green). Then switch on the upper Heating Unit XLS by

pressing its rear rocker switch to the right - the middle yellow ‘heating on’ LED

will light up. To set the microscope stage incubator temperature press Home,

Microscope, and Incubation on the microscope’s LCD panel.

If you are using the heated incubator at 37oC you should switch on the

incubator at least 2 hours before imaging. For the most stable time-lapse

imaging at 37oC leave the incubator on overnight.

The spinning disk system has the Zeiss ‘Definite Focus’ NIR LED hardware

autofocus system that fires an LED at the coverslip and keeps that distance

constant. This only works well if your cells are growing are on top of the

coverslip.

Page | 6

Using the PeCon CO2 system

The full manual is located on our core web pages and as a printed copy with

the spinning disk system manuals. The CO2 controller should be switched on

15 minutes before use and allowed to stabilise before the CO2 feed is

activated.

Operation

•Switch on the CO2-Controller. Power on/off on the back of the device.

The CO2-Controller should have a lead time of approx. 15 minutes

before the CO2 is fed in.

•After approx. 5 min. the CO2 value in the display shows 0.0. This zero

value can be corrected with the potentiometer "sensor calibration" on

the back of the device (see section maintenance).

•Press the "display" button to view the CO2 nominal value. The LED

should mark "nom". Press the “+" and "–" buttons to set the nominal

value. To view the CO2 real value press the button "display" again.

•Regulate the CO2 influx with the CO2 reducing valve. The valve should

be adjusted carefully to avoid a permanent overshoot of the CO2 value

(see guideline table 1).

•The carrying capacity of the pump can be chosen by pressing the "pump"

button. The power is increased or decreased by repeated pushing. For

5% CO2, a pump power of 2 is recommended.

•Activate the CO2 control by pressing the "valve" button. This button has

a two-color LED, Red → no gas influx and Green → CO2 flow into the

mixing chamber.

•Press the button "valve" again to deactivate the CO2 control. The LED in

the button is off.

The PeCon CO2 controller is on loan from the Zeiss 510 confocal system and

may have be used on other microscope systems occasionally (principally with

the Leica SP8 confocal).

Page | 7

Switch on Procedure

1) Switch on the 13A mains socket labelled HXP-120V. Then switch on the

epi-fluorescence HXP-120V short-arc mercury lamp power module

2) Switch on all the other 13A mains socket switches. All the microscope

control boxes should come on (always leave the Zeiss modules in the

switched on position). The Yokogawa spinning head will also come on

(the key is left in the on position). The Evolve camera should be left off

3) Switch on all the lasers using the remote control box (4 black switches)

4) Switch the HP workstation PC on, and the monitor

5) Log into the PC as Zeiss user (left option, no password)

6) When you get into the Windows 7 desktop, switch on the large Evolve

Delta 512x512 EMCCD camera

7) Start Zen Blue

8) Select Zen System (Start System)

9) Place the specimen onto the microscope

10) Use the DAPI, GFP, RFP and BF (bright field transmission) and All-Off to

select dichroics for viewing down the microscope eyepieces (under

‘Locate’ in Zen Blue).

11) Go to Zen Blue’s Acquisition to capture images

The microscope stand must not be left pushed backwards on the microscope or the

lasers will not fire (there is a safety cut-out)

12) Use the GFP/DsRed dual emission filter for faster red/green scanning

13) For complex operations like scanning multiple positions with the

motorised stage or time-lapse, press the ‘Start Experiment’ button

under Acquisition

14) The microscope will produce better images with less photo-bleaching if

the room light is left off

Page | 8

Switch off procedure

1) Remove the specimen from the microscope stage

2) Wipe off excess immersion fluid from the objective lens/top using the

Whatman 105 lens cleaning tissues provided

The 10x air objective doesn’t need cleaning after use

3) Leave the 10x objective selected on the microscope nose-piece to

minimise any possibility of damage during start-up when the XY

motorised stage initialises

4) Drop the 10x objective to the Load (lowest) position using the

microscope coarse focus control

5) Transfer image files to the network or data key

6) Shut Down the PC workstation

7) Switch off the large Evolve Delta 512x512 EMCCD camera

8) Switch off all the lasers using the remote control box (4 black switches)

9) When the PC is off switch off the epi-fluorescence HXP-120V short-arc

mercury lamp power box via the illuminated button on the front

10) Switch off all 13A mains sockets around the microscope, leaving the

module boxes themselves switched on

11) Tidy up the microscope area and leave. Switch the room light back on

as required when you leave the room.

Page | 9

________________________________________________________________

If you have any microscope/imaging problems or queries, just ask a member of

the Microscopy Core staff for help.

There is additional help and advice on our Core web-pages:

http://www.well.ox.ac.uk/microscopy

WTCHG Zeiss Cell Observer SD microscope user guide. This version updated 28th November 2014.

Inhaltsverzeichnis

Andere Zeiss Mikroskop Handbücher

Zeiss

Zeiss Axiocam MR Installations- und Betriebsanleitung

Zeiss

Zeiss LSM 510 META Bedienungsanleitung

Zeiss

Zeiss LSM800-6 Bedienungsanleitung

Zeiss

Zeiss LSM 880 Bedienungsanleitung

Zeiss

Zeiss Axioplan Universal microscope Bedienungsanleitung

Zeiss

Zeiss Axiocam MR Installations- und Betriebsanleitung

Zeiss

Zeiss OPMI CS Bedienungsanleitung

Zeiss

Zeiss LSM800-2 Bedienungsanleitung

Zeiss

Zeiss Axioskop 40 Bedienungsanleitung

Zeiss

Zeiss opmi lumera 700 Bedienungsanleitung

Zeiss

Zeiss LSM 710 Bedienungsanleitung

Zeiss

Zeiss OPMI PROergo S7 Bedienungsanleitung

Zeiss

Zeiss AxioObserver D1 Bedienungsanleitung

Zeiss

Zeiss Lattice Lightsheet 7 Bedienungsanleitung

Zeiss

Zeiss VivaTome Bedienungsanleitung

Zeiss

Zeiss Axiocam 105 color Bedienungsanleitung

Zeiss

Zeiss Axiolab Pol Bedienungsanleitung

Zeiss

Zeiss LSM 700 Bedienungsanleitung

Zeiss

Zeiss Axio Vert.A1 Bedienungsanleitung

Zeiss

Zeiss LSM 510 Inverted Bedienungsanleitung

Zeiss

Zeiss OPMI VISU 160 Bedienungsanleitung

Zeiss

Zeiss LSM 510 Inverted Bedienungsanleitung

Zeiss

Zeiss SIGMA Series Bedienungsanleitung

Zeiss

Zeiss SV8 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung