ZyXEL Communications P-2812HNU-51c Bedienungsanleitung

www.zyxel.com

Dual WAN VDSL2 IAD with

802.11n Wireless

Firmware V1.02

Edition 1, 06/2010

P-2812HNU-51c

DEFAULT LOGIN DETAILS

IP Address: 192.168.1.1

Username: Admin account: admin

User account: user

Password: Admin account: 1234

User account: user

ZyXEL Communications Corporation

Device Panels

ON/OFF

RESET

POWER

ETHERNET

PORTS

PHONE

PORTS

DSL/WAN

LEDS

WPS

WAN PORT

USB PORT

DSL PORT

Overview

The P-2812HNU-51c is a router which combines high-speed VDSL/

ADSL Internet access, a built-in switch, a firewall and high-speed

wireless networking capability. The P-2812HNU-51c comes with two

phone ports for making calls over the Internet (Voice over IP or VoIP). It

also has two USB 2.0 ports for a 3G WAN connection via a 3G wireless

card and/or sharing files via a USB compatible storage device. The P-

2812HNU-51c can also function as a print server.

Requirements

Make sure you have the following things before you start.

• Internet access - account information provided by your ISP, such as

user name, password, and so on.

• VoIP account - You need the account information provided by your

VoIP service provider (the company that lets you make phone calls

over the Internet).

• 3G account - if you want to access the Internet through a 3G

network. The P-2812HNU-51c uses this 3G connection as a

backup when the DSL or Ethernet WAN connection fails.

• Internet Explorer 6.0 and later versions, with JavaScript enabled, or

Mozilla Firefox 3 and later versions or Safari 2.0 and later versions.

Hardware Connections

Remove the P-2812HNU-51c’s plastic cover before using it.

1. Do one of the following for your Internet connection:

a. DSL: Use a telephone wire to connect this port to a telephone jack

(or the DSL or MODEM jack on a splitter, if you have one). Make

sure the DSL/WAN switch is set to the DSL side.

b. WAN: If you have a DSL router or modem already in your network

or you want to use a cable modem or optical network terminal/unit

(ONT/ONU), push the DSL/WAN switch to the WAN side and use

an Ethernet cable to connect this port to an Ethernet jack with

Internet access.

2. ETHERNET: Use an Ethernet cable to connect a computer to one of

these ports for initial configuration and/or Internet access.

3. USB 2.0: Connect a USB (version 2.0 or lower) memory stick or a

USB hard drive for file sharing, or connect a 3G wireless card for

accessing the Internet through a 3G network. You can also use a

USB cable (not provided) to connect a USB printer (version 2.0 or

lower) to this port. The P-2812HNU-51c automatically detects the

USB device. Use a USB extension cable if the stick is too big to fit.

4. PHONE: Use a telephone cable (and any telephone adaptor provided

with your P-2812HNU-51c) to connect a telephone to the PHONE 1

or PHONE 2 port. If you only have one telephone, you should use

port 1.

5. Use the power adaptor provided with your P-2812HNU-51c to

connect an appropriate power source to this socket.

6. Push the power button to the on position.

Check the LEDs

Look at the LEDs (lights) on the rear panel of the P-2812HNU-51c.

• The PWR/SYS light blinks during start-up and

is green once the P-2812HNU-51c is ready.

• An ETHERNET light turns on if the

corresponding ETHERNET port is properly

connected. An Ethernet port’s light blinks

when the P-2812HNU-51c is sending or

receiving data through it.

• The WLAN/WPS light stays green when the

wireless LAN is ready. It blinks when the P-

2812HNU-51c is sending/receiving data

through the wireless LAN.

• The DSL light stays on if a physical DSL

connection exists and blinks when

transmitting data.

The WAN light stays on if this port is properly

connected and blinks when transmitting data.

The INTERNET light is green when Internet

access is available.

• The PHONE lights stay on when your SIP

account is registered and they blink if the

receiver is off the hook.

• The USB light turns on when there is a USB

device connected to the P-2812HNU-51c and

blinks when transmitting data.

 If no lights are on, check your connections. Make sure that

you have the power adaptor connected to the P-2812HNU-

51c and plugged in to an appropriate power source. Make

sure the power source is turned on. Turn the P-2812HNU-

51c off, wait for a few seconds and turn it back on. If the

LEDs are still off, contact your local vendor.

Set Up a Wireless Network

To set up a wireless network you need at least one wireless network

card/adapter.

• If you have a desktop computer, use either a wireless USB adapter

or a wireless PCI adapter.

• If you have a laptop, use either a wireless USB adapter or a

wireless CardBus card. These are built into many laptops.

There is no wireless security enabled on the P-2812HNU-51c by default.

If you do not set wireless security, anyone within transmission range

could use your P-2812HNU-51c to access your network and the Internet.

See the User’s Guide for how to configure wireless security settings.

Setting Up a Secure Wireless Network with

WPS

If your wireless devices display the WPS logo, you

can use Wi-Fi Protected Setup (WPS) to add

wireless devices to your wireless network. If your

wireless devices do not display the WPS logo, go to

Connecting Wirelessly to your P-2812HNU-51c on page 9to have your

wireless devices join the P-2812HNU-51c’s wireless network using the

Windows wireless configuration tool.

The P-2812HNU-51c supports two WPS methods for creating a secure

connection.

• Push Button Configuration - create a secure wireless network

simply by pressing the P-2812HNU-51c’s physical WPS button.

See Push Button Configuration on page 8.

• PIN Configuration - create a secure wireless network by entering

your wireless device’s PIN (Personal Identification Number) into the

configuration screen of the P-2812HNU-51c. See your User’s

Guide for more information.

You must use the same method on the P-2812HNU-51c and the wireless

client.

If no wireless security is enabled on the P-2812HNU-51c, the P-

2812HNU-51c automatically changes to use WPA-PSK/WPA2-PSK

mixed mode and generates a pre-shared key when you use WPS.

Push Button Configuration

1. Place a WPS-enabled device that is installed in your system and

supports the WPS Push Button method within range of the P-

2812HNU-51c.

2. Press the WPS button on the P-2812HNU-

51c’s rear panel for five seconds.

3. Use the WPS-enabled device’s WPS button. It

can be either a button in the utility or a physical

button. See the device’s documentation if you

cannot locate the WPS button. It doesn’t

matter which button is pressed first. You must

press the second button within two minutes of

pressing the first one.

4. The P-2812HNU-51c and the wireless device establish a secure

connection. This can take up to two minutes.

5. Congratulations! Your computer is now ready to connect to the

Internet wirelessly through your P-2812HNU-51c.

Connecting Wirelessly to your P-2812HNU-51c

Manually configure wireless devices to join the P-2812HNU-51c’s

wireless network. If you didn’t configure the P-2812HNU-51c’s wireless

settings, use the wireless SSID (network name) on the P-2812HNU-

51c’s rear panel. If you have used WPS to set up a secure wireless

network, check the SSID and security key in the Network > Wireless

LAN > General screen after logging into the web configurator. The

connection procedure is shown here using Windows XP as an example.

1. Right-click the wireless adapter icon which appears in the bottom

right of your computer monitor. Click View Available Wireless

Networks.

2. Select the P-2812HNU-51c’s SSID name and click Connect (A). The

SSID “SecureWirelessNetwork” is given here as an example.

3. You are prompted to enter a password. Enter it and click Connect.

4. You may have to wait several minutes while your computer connects

to the wireless network.

5. You should now be securely connected wirelessly to the P-2812HNU-

51c.

Congratulations! Your computer is now ready to connect to the Internet

wirelessly through your P-2812HNU-51c.

 If you cannot connect wirelessly to the P-2812HNU-51c,

check you have selected the correct SSID and entered the

correct security key. If that does not work, ensure your

wireless network adapter is enabled by clicking on the

wireless adapter icon and clicking Enable. See the User’s

Guide for more suggestions.

Using Your Phones

Follow these directions to make calls over the Internet.

Andere Handbücher für P-2812HNU-51c

Inhaltsverzeichnis

Andere ZyXEL Communications Netzwerk-Router Handbücher

ZyXEL Communications

ZyXEL Communications Dimension ES-124P Referenzhandbuch

ZyXEL Communications

ZyXEL Communications P-2812HNU-51c Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications AES-100 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications XGS3700-24HP Betriebsanleitung

ZyXEL Communications

ZyXEL Communications LTE Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications AX Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications GS1100-16 - EDITION 1 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 623 series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-791R V2 Handbuch

ZyXEL Communications

ZyXEL Communications P-2302R-P1C Referenzhandbuch

ZyXEL Communications

ZyXEL Communications Multy Plus Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660R Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-335 Plus Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 660W Series Montageanleitung

ZyXEL Communications

ZyXEL Communications NBG4604 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications AMG1202-T10A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG3925 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660R-T1 V2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 645R Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 660R-6 Series Handbuch

ZyXEL Communications

ZyXEL Communications Prestige 2602H-6xC Handbuch

ZyXEL Communications

ZyXEL Communications VMG8324-B10A series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications p-2602hw Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG8825 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung