ACME CYC-200 FC Bedienungsanleitung

CYC-200 FC

User Manual

Please read the instructions carefully before use

CONTENTS

1. Safety Introductions.............................................................................................. 2

2. Technical Specifications......................................................................................... 3

3. How To Set The Fixture ......................................................................................... 4

3.1 Control Panel................................................................................................... 4

3.2 The Plate for Color Filter & Barn Door Installation .......................................... 5

3.3 Main Function ................................................................................................. 6

4. How To Control The Unit..................................................................................... 10

4.1 Master/Slave Function .................................................................................. 10

4.2 DMX Controller ............................................................................................. 10

4.3. DMX512 Configuration................................................................................. 11

4.4. DMX512 Connections................................................................................... 13

5. Troubleshooting .................................................................................................. 14

6. Fixture Cleaning .................................................................................................. 14

1. Safety Introductions

WARNING

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cables when fixing this unit.

Maximum ambient temperature is Ta: 40 degrees C. DO NOT operate it where the temperature

is higher than this.

Turn off the power and allow about 15 minutes for the unit to cool down before servicing.

In the event of a serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any cables during operation as high voltage may cause electric shock.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

The housing and lenses must be replaced if they are visibly damaged.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

Caution:

There are no user serviceable parts inside the unit. Do not open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. Make sure that the structure to which

you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

The equipment must be installed by professionals. It must be fixed at a place where is out of the

reach of people and no one pass by or under it.

2. Technical Specifications

◆Theatre LED Flood is a powerful cyclorama projector,with innovative optics,featuring high

power quad color LED and 90°x 113°beam angle, delivering excellent color mixing, even and

wide-field projection.

◆Control Mode: DMX, Master/Slave

◆DMX Channel: 4 / 9 Channels

◆0~100% smooth dimming

◆Color frame for use of color filters and barn doors included

◆Variable strobe speed

◆LCD display for easy navigation

Power Voltage: AC 100 ~ 240V, 50/60Hz

Power Consumption: 155W

Light Sources: 1x 150W RGBW LEDs

Beam angle: 90°x 113°

Weight: 6.2 Kgs

Dimension: 425 x 364 x 419mm

3. How To Set The Fixture

3.1 Control Panel

1. Display: Shows the various menus and the selected functions;

2. DMX IN : For DMX 512 link, use 5-pin XLR cable to link the unit to a DMX controller;

3. POWER IN: Connects to mains supply power;

4. POWER OUT: Connects to the next unit;

5. DMX OUT: For DMX 512 link, use 5-pin XLR cable to link to the next unit and output DMX

signal;

6. Power Switch: Turns On/Off the power.

7. Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

8. Fuse (T3.15A):To protect the unit from damage of over current.

3. 2 The Plate for Color Filter & Barn Door Installation

Please insert the Barn Door into the outside slot from topside as arrow ○

1E A, and fasten the lock

(Note: the Barn Door must be fastened into the inside of the lock’s hook);

Finally, as arrow A○

2E A, (Note: the lock must turn right to move) flip down the lock cap again as

arrowA○

3E A, in order to fasten the Barn Door.

3.3 Main Function

To select any of the given functions, press the MENU button up to the required selection as shown

on the display. Select the function with the ENTER button and the display will blink. Use the

DOWN/UP buttons to change the mode. Once the required mode has been selected, press the

ENTER button to confirm. To go back to the main functions without any changes press the MENU

button again. Press and hold the MENU button for about one second or wait for 7 seconds to exit

the current mode.

The main functions are shown below:

Mode1(4ch)

Red Value

Green Value

Blue Value

White Value

DMX Settings

To select DMX Settings, press the ENTER button to confirm, use the UP/DOWN button to select

DMX Address,Channel Mode or View DMX Value.

DMX Address

To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to

adjust the address from 1to 512, press the ENTER button to store. Press the MENU button

back to the last menu or let the unit idle one minute to exit menu mode.

Channel Mode

To select Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to

select Mode 1 (4 ch) or Mode 2 (9 ch) mode, press the ENTER button to store. Press the

MENU button back to the last menu or let the unit idle one minute to exit menu mode.

View DMX Value

To select View DMX Value, press the ENTER button to confirm. Use the UP/DOWN button to

select Red, Green, Blue or White mode, press the ENTER button to store. Press the MENU

button back to the last menu or let the unit idle one minute to exit menu mode.

Dimmer Curve

To select Dimmer Curve, press the ENTER button to show the DIMMER CURVE on the display, use

the UP/DOWN button to select Mode 1,Mode 2,Mode 3 or Mode 4. Once selected, press the

ENTER button to store. Press the MENU button back to the last menu or let the unit idle one

minute to exit menu mode.

Square Law: Light intensity control is finer at low levels and coarser at high levels.

Inverse Square Law: Light intensity control is coarser at low levels and finger at high levels.

Linear: The increase in light intensity appears to be linear as DMX value is increased.

S-cure: Light intensity control is finger at low levels and high levels and coarser at medium levels.

Dimmer Speed

To select Dimmer Speed press the ENTER button to confirm, present mode will blink on the display,

use the UP/DOWN button to select the SMOOTH (dimmer speed smooth) or FAST(dimmer speed

fast) press the ENTER button to store. Press the MENU button back to the last menu or let the unit

idle one minute to exit menu mode.

Display Settings

Enter menu mode, select Display Settings, press ENTER button to confirm, use UP/DOWN button

to select Display Inverse,Backlight Auto Off, Contrast Ratio, Temperature Unit or Language.

Display Inverse

To select Display Inverse, press the ENTER button to confirm, present mode will blink on the

display, use the UP/DOWN button to select the No (normal display) or Yes (inverse display),

press the ENTER button to save. Press the MENU button back to the last menu or let the unit

idle one minute to exit menu mode.

Backlight Auto Off

To select Backlight Auto Off, press the ENTER button to confirm, present mode will blink on

the display, use the UP/DOWN button to select Yes (display goes off one minute after exiting

menu mode) or No (display always on), press the ENTER button to save. Press the MENU

button back to the last menu or let the unit idle one minute to exit menu mode.

Contrast Ratio

To select Contrast Ratio, press the ENTER button to confirm, present mode will blink on the

display, use the UP/DOWN button to adjust the value from 1 to 30, press the ENTER button

to save. Press the MENU button back to the last menu or let the unit idle one minute to exit

menu mode.

Language

To select Language, press the ENTER button to confirm, present mode will blink on the

display, use the UP/DOWN button to select the English or Chinese, press the ENTER button

to store. Press the MENU button back to the last menu or let the unit idle one minute to exit

menu mode.

Fixture Test

To select Fixture Test press the ENTER button to confirm, present mode will blink on the display,

use the UP/DOWN button to select the Auto Test or Manual Test press the ENTER button to store.

Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Fixture Information

Enter menu mode, select Fixture Information, press the ENTER button to confirm, use the

UP/DOWN button to select the Fixture Use Time,LED Temp. or Firmware Version.

Fixture Use Time

To select Fixture Use Time, press the ENTER button to confirm, and running time of the

fixture will show on the display. Press the MENU button back to exit.

LED Temp.

To select LED Temp., press the ENTER button to confirm, the current running temperature of

the fixture will show on the display. Press the MENU button back to exit.

Firmware Version

To select Firmware Version, press the ENTER button to confirm, the software version will

show on the display. Press the MENU button back to exit.

Factory Setting

Select Factory Setting,press the ENTER button to confirm, present mode will blink on the display.

Use the DOWN and UP button to select the No or Yes (Switch back to default settings). Hold and

press the MENU button about one second or wait for one minute to exit the menu mode.

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME E-10T WW DXX Bedienungsanleitung

ACME

ACME LED-BL4B Bedienungsanleitung

ACME

ACME LED-MTX25 IP Bedienungsanleitung

ACME

ACME XA-500 Bedienungsanleitung

ACME

ACME LED-MTX36 HEX Bedienungsanleitung

ACME

ACME IM-5S-ELC Bedienungsanleitung

ACME

ACME AE-610 BEAM Bedienungsanleitung

ACME

ACME ENERGY HYBRID Bedienungsanleitung

ACME

ACME MACE Bedienungsanleitung

ACME

ACME Stage Panel 1080 Bedienungsanleitung

ACME

ACME LP-TS200 CW Bedienungsanleitung

ACME

ACME Spartan Hybrid Bedienungsanleitung

ACME

ACME MH-275R Bedienungsanleitung

ACME

ACME SPLENDOR 90 Bedienungsanleitung

ACME

ACME SAMBA Color Bedienungsanleitung

ACME

ACME CA-DD12 II Bedienungsanleitung

ACME

ACME Color Spot Bedienungsanleitung

ACME

ACME ORION XP-260 BEAM Bedienungsanleitung

ACME

ACME E-40D TC DXX Bedienungsanleitung

ACME

ACME IU-01 Bedienungsanleitung

ACME

ACME Dragonfly Quad Bedienungsanleitung

ACME

ACME iMove 50SR Bedienungsanleitung

ACME

ACME Ellipsoidal E-300 D2550 Bedienungsanleitung

ACME

ACME Stage Blinder P4 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung