ACME Theatre Spot 150 Bedienungsanleitung

User Manual

Please read the instruc on carefully before use

TS-150 CW

TS-150 WW

-TS-150 WW W

TS-1504 CW

TS-1504 WW

CONTENTS

1. Safety Instructions ................................................................................. 2

2. Technical Specifications ......................................................................... 3

3. The Plate for Color Filter & Barn Door Installation................................. 5

4. How To Set The Unit............................................................................... 6

4.1 Control panel ................................................................................... 6

4.2 Main Functions ................................................................................ 7

5. How to Control the Unit....................................................................... 12

5.1 Master/Slave Built In Preprogrammed Function ............................ 12

5.2 DMX Controller .............................................................................. 12

5.3 DMX 512 Configurations ................................................................ 13

6. DMX 512 Connections ......................................................................... 13

7. Troubleshooting ................................................................................... 14

8. Fixture Cleaning ................................................................................... 15

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction manual.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this.

Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its

operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

In the event of serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

Please read the instruction carefully which includes important

information about the installation, usage and maintenance.

moisture.

DO NOT open the unit within five minutes after switching off.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution

There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to

which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people and has no one pass by or under it.

2. Technical Specifications

◆The best price-performance ratio LED theater spot, engineered to exceed conventional

projectors in performance and power

◆DMX, Master/Slave and manual control

◆Motorized linear zoom for beam angle from 14~55°

◆0~100% smooth dimming

◆Color frame for use of color filtersand barn doors included

◆LCD display for easy navigation

◆Knobs for manually control of zoom and dimming are available at rear side

◆TS-150 WW/CW with Chinese Fresnel lens

◆TS-1504 WW/CW with German Fresnel lens

Power supply: AC 100~240V, 50/60Hz

Power consumption: 190W

Color Temperature: 5600+100K (TS-150 CW)

3150+100K (TS-150 WW)

Light Source: 1 × 150W white LED

CRI:

WW: ≥92

CW: ≥89

Weight: 8.6Kgs

Dimension: 406×417×238mm

Photometric Diagram:

Distance(m) 3 5 7 10

14 Lux CW 6920 2300 1175 575

WW 6240 2380 1215 595

55 Lux CW 2240 820 420 205

WW 2000 840 430 210

° °

3. The Plate for Color Filter & Barn Door Installation

Fig. 1

At first, please push the Lock Cap button by hand as the arrow ○

1E A, and move away the Lock as the

arrow A○

2E A; Then insert the Plate for Color Filter into the inside slot from topsideA○

3E A;

Fig. 2

Secondly, please insert the Barn Door into the outside slot from topside as arrow A○

4E A, and fasten

the lock (Note: the Barn Door must be fastened into the inside of the lock’s hook ); then flip down

the lock cap again as arrowA○

5E A.

4. How To Set The Unit

4.1 Control panel

1. Display: Show the various menus and the selected functions.

2. LED:

MASTER On Master Mode

SLAVE On Slave Mode

DMX On DMX input present

3. Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

4. Dimmer: Manual adjust the dimmer value.

5 Zoom: Manual adjust the zoom value.

6. DMX input: For DMX512 link, use 5-pin XLR cable to link the unit together.

7. POWER IN: Connects to mains supply power.

8. POWER OUT: Connects to the next unit.

9. DMX output: For DMX512 link, use 5-pin XLR cable to link the unit together.

10. Fuse(T5A): Used to protect the unit from damage of the over current.

11.ETHERNET: Connect with the multimedia and use software to control the units via ArtNet;.

4.2 Main Functions

To select any functions, press the MENU button until the required one is shown on the display.

Select the function by ENTER button and the display will blink. Use the DOWN and UP button to

change the mode. Once the required mode has been selected, press the ENTER button to setup or

it will automatically return to the main functions without any change after idling one minute. Back

to the functions without any change press the MENU button.

The main functions are shown below:

DMX Setting

Enter menu mode, select DMX Setting, press ENTER button to confirm, use UP/DOWN button to

select DMX Address, Art-Net Setup or Channel Mode.

Select DMX Address, press the ENTER button to confirm, the present address will blink on

the display. Use the UP and DOWN button to adjust the DMX address from 1to 512. Once

the address has been selected, press the ENTER button to save. Hold and press the MENU

button about one second or wait for one minute to exit the menu mode.

Select Art-Net Setup, press the ENTER button to confirm, the present mode will blink on the

display. Use the DOWN and UP button to select the Ethernet IP Setup or Art-Net Port Setup

mode. Once the address has been selected, press the ENTER button to save. Hold and press

the MENU button about one second or wait for one minute to exit the menu mode.

Select Channel Mode, press the ENTER button to confirm, the present mode will blink on

the display. Use the DOWN and UP button to select the 2 CH or 3 CH mode. Once the

address has been selected, press the ENTER button to save. Hold and press the MENU

button about one second or wait for one minute to exit the menu mode.

Dimmer Speed

Select Dimmer Speed, press the ENTER button to confirm, present mode will blink on the display.

Use the DOWN and UP button to select the Smooth (dimmer speed smooth) or Fast(dimmer

speed fast) mode. Once the mode has been selected, press the ENTER button to save. Hold and

press the MENU button about one second or wait for one minute to exit the menu mode.

Dimmer Curve Setting

Select Dimmer Curve Setting, press the ENTER button to confirm, present mode will blink on the

display. Use the UP/DOWN button to select Linear Curve, Sq.Law Curve, Invert Sq. Law Curve or S

Curve. Once selected, press the ENTER button to store. Press the MENU button back to the last

menu or let the unit idle one minute to exit menu mode.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME Thunderbreaker Bedienungsanleitung

ACME

ACME LED-PS10 Bedienungsanleitung

ACME

ACME CM-150 PAGEANT 150 Bedienungsanleitung

ACME

ACME CHIRON Bedienungsanleitung

ACME

ACME Thunder Bedienungsanleitung

ACME

ACME Spartan Hybrid Bedienungsanleitung

ACME

ACME LED-747-1W Bedienungsanleitung

ACME

ACME Sandane Bedienungsanleitung

ACME

ACME TV LIGHT PANEL 2000 Bedienungsanleitung

ACME

ACME Pageant CM-200Z Bedienungsanleitung

ACME

ACME Neozone Bedienungsanleitung

ACME

ACME IL-2420 II Bedienungsanleitung

ACME

ACME CP-18TC Bedienungsanleitung

ACME

ACME LS-1005 Bedienungsanleitung

ACME

ACME GLAMOUR 700Z RGBY Bedienungsanleitung

ACME

ACME VENOM LED-460 Bedienungsanleitung

ACME

ACME HYGIEA Bedienungsanleitung

ACME

ACME FESTIVAL Bedienungsanleitung

ACME

ACME BP-183 RGBW S R DXX Bedienungsanleitung

ACME

ACME Libre Bedienungsanleitung

ACME

ACME Solar Flare Bedienungsanleitung

ACME

ACME LED-PS10 Bedienungsanleitung

ACME

ACME Ozone 3 Bedienungsanleitung

ACME

ACME Uploader II Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung