ACME LP-F1000 CW Bedienungsanleitung

User Manual

Please read the instruc on carefully before use

LP-F1000 CW

LP-F1000 WW

2018.06.25

审核

受控正本

CONTENTS

1. Safety Introductions.............................................................................................. 2

2. Technical Specifications......................................................................................... 3

3. How To Set The Fixture ......................................................................................... 4

3.1 Control Panel................................................................................................... 4

3. 2 The Plate for Barn Door Installation ............................................................... 5

4. How To Control The Unit ..................................................................................... 10

4.1 Master/Slave Function .................................................................................. 11

4.2 DMX Controller ............................................................................................. 11

4.3. DMX512 Configuration................................................................................. 12

4.4. DMX512 Connections................................................................................... 13

5. Troubleshooting .................................................................................................. 14

6. Fixture Cleaning .................................................................................................. 14

1. Safety Introductions

WARNING

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cables when fixing this unit.

Maximum ambient temperature is Ta: 40 degrees C. DO NOT operate it where the temperature

is higher than this.

Turn off the power and allow about 15 minutes for the unit to cool down before servicing.

In the event of a serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any cables during operation as high voltage may cause electric shock.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

The housing and lenses must be replaced if they are visibly damaged.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

Caution:

There are no user serviceable parts inside the unit. Do not open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. Make sure that the structure to which

you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

The equipment must be installed by professionals. It must be fixed at a place where is out of the

reach of people and no one pass by or under it.

2. Technical Specifications

Power Voltage: AC 100 ~ 240V, 50/60Hz

Power Consumption: 100W

Light Sources: 240 pcs CW LED (LP-F1000 CW)

240 pcs WW LED (LP-F1000 WW)

Color Temperature: 3200±150K

5600±250K

Beam Angle

：

130°

CRI

：

≥94

Weight: 9.2Kgs

Dimension: 673 x 306 x 144mm

306

673

144

3. How To Set The Fixture

3.1 Control Panel

2345678

1. Display: Shows the various menus and the selected functions.

2. Button:

To select the programming functions

DOWN

To go backward in the selected functions

To go forward in the selected functions

ENTER To confirm the selected functions

3. Dimmer Knob: Adjust the dimmer;

4. Mains In: Connects to mains supply power;

5. Fuse (T2A): To protect the unit from damage of over current;

6. Battery DC48V: Connects to external battery;

7. DMX IN/OUT : For DMX 512 link, use 5-pin XLR cable to link the unit to a DMX controller or the

next unit and output DMX signal;

8. ETHERNET:

Connect with the multimedia and use software to control the units via ArtNet;

3. 2 The Plate for Barn Door Installation

At first, please push the barn door by hand.

Screw

Secondly, please put the Barn Door into the unit, to fasten the screws of the slot, then finish the

barn door installation.

3.3 Main Function

To select any of the given functions, press the MENU button up to the required selection as shown

on the display. Select the function with the ENTER button and the display will blink. Use the

DOWN/UP buttons to change the mode. Once the required mode has been selected, press the

ENTER button to confirm. To go back to the main functions without any changes press the MENU

button again. Press and hold the MENU button for about one second or wait for 7 seconds to exit

the current mode.

The main functions are shown below:

DMX Address

Channel Mode

1 CH

DMX Setting A Setup

-Net

Slave Mode

Slave

Master

Dimmer Curve Square Law Curve

Linear Curve

S Curve

DMX State

IP Address

Net

Sub-Net

255

Universe

3 CH

Invert Square Law Curve

immer Speed

Smooth

avt

512

Blackout

Master Slave

Hold

2 CA H

2 CB H

Display Setting

Backlight Auto Off

Contrast Ratio

Invert Display

Firmware Version

Fixture Time

Language

Englivh

Chinese

Manual Mode

255

Dimmer

DMX Setting

Select the DMX Setting, press the ENTER button to confirm. Use the UP and DOWN button to

select DMX Address, Art-Net Setup or Channel Mode.

DMX Address

Select the DMX Address, press the ENTER button to confirm, the display will show the present

address. Use the UP and DOWN button to select 1to 512, press the ENTER button to store.

Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.

Art-Net Setup

Select the Eth-Net Address, press the ENTER button to confirm. Use the UP and DOWN button

to select the address for EtherNet IP Setup or ArtNet Port Setup,press the ENTER button to set

the value for these items. Press the MENU button back to the last menu or idling 30 seconds to

exit menu mode.

Channel Mode

Select the Channel Mode, press the ENTER button to confirm, the display will show the present

channel mode. Use the UP and DOWN button to select 1 CH, 2A CH, 2B CH or 3 CH, press the

ENTER button to store. Press the MENU button back to the last menu or idling 30 seconds to

exit menu mode.

Dimmer Speed

Select the Dimmer Speed, press the ENTER button to confirm, use the UP and DOWN button to

select the Fast or Smooth mode, press the ENTER button to store. Press the MENU button back to

the last menu or idling 30 seconds to exit menu mode.

Dimmer Curve

Select Dimmer Curve, press the ENTER button to show the DIMMER CURVE on the display. Use

the DOWN/UP button to select the Mode 1,Mode 2, Mode 3 or Mode 4. Once the dimmer mode

has been selected, press the ENTER button to setup, to go back to the functions without any

change press the MENU button again. Press and hold the MENU button for about one second or

wait for one minute to exit the menu mode.

Mode 1(Optically Linear):

The increase in light intensity appears to be linear as DMX value is increased.

Mode 2(Square Law):

Light intensity control is finer at low levels and coarser at high levels.

Mode 3(Inverse Square Law):

Light intensity control is coarser at low levels and finger at high levels.

Mode 4(S-cure):

Light intensity control is finger at low levels and high levels and coarser at medium levels.

Slave Mode

Select the Slave Mode, press the ENTER button to confirm, use the UP and DOWN button to

select the Master or Slave mode, press the ENTER button to store. Press the MENU button back to

the last menu or idling 30 seconds to exit menu mode.

DMX State

Select DMX State, press the ENTER button to confirm, the present mode will blink on the display,

use the UP and DOWN button to select Master Slave, Blackout or Hold,press the ENTER button to

store. Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.

Frequency

Select Frequency,press the ENTER button to confirm, the present mode will blink on the display,

use the UP and DOWN button to select 900hz, 1000hz , 1100hz , 1200hz , 1300hz , 1400hz ,

1500hz , 2500hz , 4000hz , 5000hz , 10000hz , 15000hz , 20000hz or 25000hz,press the ENTER

button to store. Press the MENU button back to the last menu or idling 30 seconds to exit menu

mode.

Display Setting

Select Display Setting, press the ENTER button to confirm, use the UP and DOWN button to select

Contrast Ratio, Backlight Auto off , Invert Display or Language.

Contrast Ratio

Select Contrast Ratio, press the ENTER button to confirm, the present mode will blink on the

display, use the UP and DOWN button to adjust from 1 to 30,press the ENTER button to store.

Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.

Backlight Auto Off

Select Backlight Auto Off, press the ENTER button to confirm, the present mode will blink on

the display, use the UP and DOWN button to select No or Yes,press the ENTER button to store.

Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.

Invert Display

Select Invert Display, press the ENTER button to confirm, the present mode will blink on the

display, use the UP and DOWN button to select No or Yes,press the ENTER button to store.

Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME ASTRO LED-256D Bedienungsanleitung

ACME

ACME DELUGE LED-WAV-50W Bedienungsanleitung

ACME

ACME Diabolo Bedienungsanleitung

ACME

ACME LED-212RGB Bedienungsanleitung

ACME

ACME BW-54-10FC II RL Bedienungsanleitung

ACME

ACME PEXEL 100 Bedienungsanleitung

ACME

ACME ColorTec 250 LED-CC60 Bedienungsanleitung

ACME

ACME Theatre Spot 150 Bedienungsanleitung

ACME

ACME Building wash Bedienungsanleitung

ACME

ACME LED-747-1W Bedienungsanleitung

ACME

ACME GEIST BSWF Bedienungsanleitung

ACME

ACME BTDG40 Bedienungsanleitung

ACME

ACME Spartan Hybrid Bedienungsanleitung

ACME

ACME Theatre Spot 150m Bedienungsanleitung

ACME

ACME Solaris Bedienungsanleitung

ACME

ACME LED-275 D Bedienungsanleitung

ACME

ACME COOLIE 14FC Bedienungsanleitung

ACME

ACME LED-PS10D RGBW Bedienungsanleitung

ACME

ACME Warrior Scan 50 LED-SC50C Bedienungsanleitung

ACME

ACME Inferno Bedienungsanleitung

ACME

ACME HYGIEA Bedienungsanleitung

ACME

ACME Xperior 700SZ Spot Bedienungsanleitung

ACME

ACME Dynamic 25 Roller LED-SC25B Bedienungsanleitung

ACME

ACME XP-5000WZ Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung