ACME Diabolo Bedienungsanleitung

CONTENTS

1. Safety Instructions ......................................................................................... 2

2. Technical Specifications ................................................................................. 4

3. Control Panel ................................................................................................. 5

4. How To Set The Unit....................................................................................... 6

4.1 Main Function.......................................................................................... 6

4.2 Home Position Adjustment .................................................................... 13

5. Control By Universal DMX Controller ........................................................... 14

5.1 DMX512 Connection.............................................................................. 14

5.2 Address Setting ...................................................................................... 15

5.3 DMX512 Configuration........................................................................... 16

6. Error Information......................................................................................... 22

7. Troubleshooting........................................................................................... 24

8. Fixture Cleaning ........................................................................................... 25

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will

not accept liability for any resulting defects or problems.

Unpack and check carefully that there is no transportation damage before using the unit.

This product is for indoor use only. Use only in a dry location.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.

DO NOT connect the device to any dimmer pack.

Make sure there are no flammable materials close to the unit while operating to avoid fire

hazard.

Examine the power wires carefully; replace them immediately if there is any damage.

Unit’s surface temperature may reach up to 75℃. DO NOT touch the housing bare-handed

during its operation.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut

off the mains power immediately.

DO NOT operate in dirty or dusty environment, do clean fixtures regularly.

Please read the instruction carefully which includes important information about

the installation, usage and maintenance.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together twist other cables.

The minimum distance between light output and the illuminated surface must be more than

0.5 meters.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance center if

needed.

Disconnect the mains power if the fixture is has not been used for a long time.

DO use the original packing materials before transporting it again.

DO NOT look directly at the light while the bulb is on.

DO NOT start on the unit without bulb enclosure or when housing is damaged.

Installation:

The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of the

fixtures weight. Always use a safety cable that can hold 12 times of the weight of the fixture when

installing.

The equipment must be installed by professionals. It must be installed in a place where is out of the

reach of people and no one can pass by or under it.

2. Technical Specifications

Power Voltage:

AC 100~240V, 50/60Hz

Power Consumption:

280W

Light Source:

19x20W RGBW LED

Zoom Range:

10°~60°

Movement:

Pan: 540°

Tilt: 225°

Pan/Tilt Resolution: 16bit

Dimmer/Shutter:

Smooth dimming from 0~100%; outstanding strobe effect with variable speed

Control:

DMX channel: 1 1/1 4/15/14* channels

Control Mode: DMX512, RDM

Firmware Upgrade: Update via DMX link & USB

Construction:

Display: LCD display

Data In/Out: 3-pin XLR

Power In/Out: Power Cord out/Power Connector in/out

Protection Rating: IP20

Features:

Electronic linear zoom system

Outstanding color macro effect

Fast and mute operating, flicker free

Dimension/Weight:

309.6x222.5x371.9mm, 8.8kgs

12.2"x8.8"x14.6"in, 19.4lbs

Photometric Diagram:

3. Control Panel

WIRE VERSION:

POWERCON VERSION1:

POWERCON VERSION2:

1. DISPLAY: To show the various menus and the selected function

2. Button:

To enter into move backward or leave the menu

To go backward to move up in the menu

DOWN

To go forward to move down in the menu

ENTER

To perform the desired functions

3. POWER: To connect to supply power

4. DMX IN:For DMX512 link, use 3-pin XLR cable to link the unit and DMX controller

5. DMX OUT: For DMX512 link, use 3-pin XLR cable to link the next units

6. FIRMWARE UPGRADE: Use to upgrade fixture’s firmware

7. POWERCON OUT: To connect to the next fixture

8. POWERCON IN: To connect to supply power

4. How To Set The Unit

4.1 Main Function

Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until

the required function is shown on the monitor. Select the function by the ENTER button. Use the

UP/DOWN button to choose the submenu, press the ENTER button to store and automatically

return to the last menu. Press the MENU button or let the unit idle 30 seconds to exit menu mode.

The main functions are shown below:

DMX Settings

To select DMX Settings, press the ENTER button to confirm, use the UP/DOWN button to select

DMX Address, DMX Channel Mode, No DMX Status or View DMX Value.

DMX Address

To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to adjust the

address from 001 to 502/499/4 9 8/4 9 9 , press the ENTER button to store. Press the MENU button back

to the last menu or let the unit idle 30 seconds to exit menu mode.

DMX Channel Mode

To select DMX Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to

select Mode1 (11), Mode2 (14), Mode3 (15) or Mode4 (14*), press the ENTER button to store.

Press the MENU button back to the last menu or let the unit idle 30 seconds to exit menu mode.

No DMX Status

To select No DMX Status, press the ENTER button to confirm. Use the UP/DOWN button to select

Blackout or Hold, press the ENTER button to store. Press the MENU button back to the last menu or

let the unit idle 30 seconds to exit menu mode.

View DMX Value

To select View DMX Value, press the ENTER button to confirm. Use the UP/DOWN button to view

the DMX channel value. Press the MENU button back to the last menu or let the unit idle 30

seconds to exit menu mode.

Fixture Settings

To select Fixture Settings, press the ENTER button to confirm, use the UP/DOWN button to select

Pan Invert, Tilt Invert, P/T Feedback, White Balance, Dimmer Curve or Dimmer Speed.

Pan Invert

To select Pan Invert, press the ENTER button to confirm. Use the UP/DOWN button to select

No(normal) or Yes(pan invert), press the ENTER button to store. Press the MENU button back to the

last menu or let the unit idle 30 seconds to exit menu mode.

Tilt Invert

To select Tilt Invert, press the ENTER button to confirm. Use the UP/DOWN button to select

No(normal) or Yes(tilt invert), press the ENTER button to store. Press the MENU button back to the

last menu or let the unit idle 30 seconds to exit menu mode.

P/T Feedback

To select P/T Feedback, press the ENTER button to confirm. Use the UP/DOWN button to select

No(Pan or tilt’s position will not feedback while out of step) or Yes(Feedback while pan/tilt out of

step), press the ENTER button to store. Press the MENU button back to the last menu or let the unit

idle 30 seconds to exit menu mode.

White Balance

To select White Balance, press the ENTER button to confirm. Use the UP/DOWN button to select

Red, Green or Blue, press the ENTER button to confirm. Use the UP/DOWN button to adjust the

value from 125 to 255, press the ENTER button to store. Press the MENU button back to the last

menu or let the unit idle 30 seconds to exit menu mode.

Dimmer Curve

To select Dimmer Curve, press the ENTER button to confirm. Use the DOWN/UP button to select

Linear, Square Law, Inv SQ Law or S Curve. Once the mode has been selected, press the ENTER

button to setup. To go back to the functions without any change, press the MENU button.

Optically Linear: The increase in light intensity appears to be linear as DMX value is increased.

Square Law: Light intensity control is finer at low levels and coarser at high levels.

Inverse Square Law: Light intensity control is coarser at low levels and finger at high levels.

S-Curve: Light intensity control is finger at low levels and high levels and coarser at medium levels.

Dimmer Speed

To select Dimmer Speed, press the ENTER button to confirm. Use the UP/DOWN button to select

Fastor Smooth, press the ENTER button to store. Press the MENU button back to the last menu or

let the unit idle 30 seconds to exit menu mode.

Display Settings

To select Display Settings, press the ENTER button to confirm, use the UP/DOWN button to select

Display Invert, Backlight Intensit, Temperature Unit, Display Warning or Language.

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME LED-212RGB Bedienungsanleitung

ACME

ACME LED-245/2 Bedienungsanleitung

ACME

ACME SABER HYBRID PRO Bedienungsanleitung

ACME

ACME COMET Bedienungsanleitung

ACME

ACME LED-0408 Bedienungsanleitung

ACME

ACME Oxygen Bedienungsanleitung

ACME

ACME Dynamic 25 Roller LED-SC25B Bedienungsanleitung

ACME

ACME Xperior 1500SZ Bedienungsanleitung

ACME

ACME Dragon Scan 50 LED-SC50B Bedienungsanleitung

ACME

ACME GLAMOUR 700Z RGBY Bedienungsanleitung

ACME

ACME FLASHDOT Bedienungsanleitung

ACME

ACME BRIGHT Bedienungsanleitung

ACME

ACME Dotline180 Bedienungsanleitung

ACME

ACME LED-256D-10W Bedienungsanleitung

ACME

ACME COOLIE 14FC Bedienungsanleitung

ACME

ACME Thunderstruck LP-2304 Bedienungsanleitung

ACME

ACME IP Cabin AR-01 Bedienungsanleitung

ACME

ACME Xperior XP-380 BEAM IP F Bedienungsanleitung

ACME

ACME ENERGY HYBRID X-400 BSW Bedienungsanleitung

ACME

ACME LED-PS10 Bedienungsanleitung

ACME

ACME iSolution Bedienungsanleitung

ACME

ACME ANIMA C Bedienungsanleitung

ACME

ACME FESTIVAL Bedienungsanleitung

ACME

ACME Theatre Spot 150 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung