ACME Xperior XP-380 BEAM IP F Bedienungsanleitung

XP-380 BEAM IP F

CONTENTS

1. Safety Instructions ................................................................................. 2

2. Technical Specifications ......................................................................... 3

3. Description............................................................................................. 5

3.1 Control Panel ................................................................................ 5

4. Gobo/Color and Lamp............................................................................ 6

4.1 Gobos/Color.................................................................................. 6

4.2 Light Source.................................................................................. 6

5. How To Set The Unit............................................................................... 7

5.1 Main Function................................................................................ 7

5.2 Home Position Adjustment........................................................ 14

5.3 Error Information......................................................................... 16

6. Control By Universal DMX Controller ................................................... 17

6.1 Connection .................................................................................. 17

6.2 Address Setting........................................................................... 18

6.3 DMX 512 Configuration ............................................................. 18

7. Troubleshooting ................................................................................... 23

8. Maintenance and Cleaning .................................................................. 25

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer

will not accept liability for any resulting defects or problems.

Unpack and check carefully that there is no transportation damage before using the unit.

The unit is for indoor use only. Use only in a dry location.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Maximum ambient temperature TA: 40℃，Minimum ambient temperature TA: 0℃.

DO NOT connect the device to any dimmer pack.

During initial start-up some smoke or smell may arise. This is a normal process and does not

necessarily mean that the device is defective, and it will decrease gradually within 15 minutes.

Make sure there are no flammable materials close to the unit while operating to avoid fire hazard.

Examine the power wires carefully; replace them immediately if there is any damage.

Unit’s surface temperature may reach up to 89℃. DO NOT touch the housing bare-handed during

its operation, and allow about 15 minutes for cooling the unit down before replacing bulb or

maintenance as it could be very hot.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut off

Please read the instruction carefully which includes important information about

the installation, usage and maintenance.

the mains power immediately.

DO NOT operate in dirty or dusty environment, do clean fixtures regularly.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together twist other cables.

The minimum distance between light output and the illuminated surface must be more than 12

meters.

Disconnect mains power before fuse/lamp replacement or servicing.

Replace fuse/lamp only with the same type.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage

or malfunction. Please contact the nearest authorized technical assistance center if needed.

Disconnect the mains power if the fixture is has not been used for a long time.

DO use the original packing materials before transporting it again.

Cautions:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

Hot lamp explosion hazard. DO NOT open the unit within 15 minutes after switching off.

DO replace the bulb once it is damaged, deformed or life-expired.

DO NOT look directly at the light while the bulb is on.

Never touch bulb with bare fingers, as it is very hot after using.

DO NOT start on the unit without bulb enclosure or when housing is damaged.

2. Technical Specifications

Power supply：

AC 100~240V ,50/60Hz

Power Consumption：

535W

Display

：

OLED

Protection Rating

：

IP65

Color Temperature

：

7800K

Beam Angle

：

3°

Light Source

OSRAM SIRIUS HRI®370W LL

Optical system

High efficiency optical system, delivering extremely powerful output

High quality dichroic lenses

Movement

Pan: 540°

Tilt: 270°

Pan/Tilt moving speed adjustable.

Automatic Pan/Tilt correction.

Easy calibration and maintenance by magnetic home positioning.

Pan/Tilt position lock for transporting protection.

Dimmer/Shutter

Blackout, 0~100% smooth dimming, independent shutter and various strobe effect.

Color wheel

Color wheel: 12 fixed colors plus open with rainbow effect

Gobo wheel

Gobo Wheel : 1 Rotating gobo wheel with 12 gobos plus open

Prism

8 facet prism+24 facet prism, both of them can rotate in both directions and overlay

Protocols

DMX 512

Date input/output: 3 Pin XLR socket

Dimension/Weight

402× 330×628mm，30Kg

15.8"x12.9"x24.7"in, 66.1lbs

3. Description

3.1 Control Panel

1. Monitor:

2. Button:

MENU To enter into move backward or leave the menu

UP To go backward to move up in the menu

DOWN To go to move down in the menu

ENTER To perform the desired functions

3. DMX output:

DMX 512 operation, use 3 XLR cable to link the next units.

4. DMX input:

628 mm

402 mm

330 mm

DMX 512 link, use 3 XLR cable to link the unit and DMX controller.

5. Power In:

To connect to the mains supply

6. Power Out:

To connect to the next fixture

4. Gobo/Color and Lamp

4.1 Gobos/Color

CAUTION: Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be

opened!

4.2 Light Source

OSRAM SIRIUS HRI®370W LL

Because of its high internal pressure, there might be a risk that the Discharge lamp would

explode during operation. The lamp emits intense UV radiation which is harmful to the

eyes and skin. The high luminance of the arc can cause severe damage to the retina if you

take a close look at the lamp.

DANGER!

Install the gobos with the device switched off only.

Unplug from mains before changing gobos!

To protect the lamp, always turn off the lamp first (via control panel or DMX controller)

and let the unit run at least five minutes to cool down before switching off the mains

supply. Never handle the lamp or luminary when it is hot.

Do not touch the bulb with bare hands. If this happens, clean the lamp with denatured

alcohol and wipe it with a lint free cloth before installation.

The lamp generates UV radiation. Never operate the lamp without appropriate shielding.

When lighting up, the lamp operates at high pressure and there is a slight risk of arc tube

rupture. The risk increases with age, temperature and improper handling of the lamp. Do not

use the lamp longer than its lifespan.

Make sure the lamp is located in the center of the reflector for the best projection.

5. How To Set The Unit

5.1 Main Function

Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until the

required function is shown on the monitor. Select the function by the ENTER button. Use the

UP/DOWN button to choose the submenu, press the ENTER button to store and automatically return

to the last menu. Press the MENU button or let the unit idle one minute to exit menu mode.

In the event of disconnecting with mains power, press the UP button for one minute to enter into

menu mode. Press MENU button or let the unit idle one minute to exit.

The main functions are shown below（the grayed boxes are preset settings）:

DMX Functions

To select DMX Functions press the ENTER button to confirm, use the UP/DOWN button to select DMX

Address, Channel Mode , DMX State or View DMX Value.

DMX Address —DMX512 address setting

To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to adjust

the address from 001 to 499/496, press the ENTER button to store. Press the MENU button back

to the last menu or let the unit idle one minute to exit menu mode.

Channel Mode — channel mode

To select Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to select

Mode1 (14) channels mode or Mode2 (17) channels mode , press the ENTER button to store.

Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode.

DMX State —fixture state while DMX single stops

To select DMX State, press the ENTER button to confirm. Use the UP/DOWN button to select

Blackout (fixture blacks out if DMX signal stops) or Hold (fixture continues to obey the last

command it received Via DMX if DMX signal stops), press the ENTER button to store. Press the

MENU button back to the last menu or let the unit idle one minute to exit menu mode.

View DMX Value

To select View DMX Value, press the ENTER button to confirm. Use the UP/DOWN button to view

the DMX channel value. Press the MENU button back to the last menu or let the unit idle one

minute to exit menu mode.

Fixture Settings

To select Fixture Settings, press the ENTER button to confirm, use the UP/DOWN button to select Pan

Inverse, Tile Inverse or P/T Feedback.

Pan Inverse

To select Pan Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select No

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME Dynamic 25 Spin LED?GF25 Bedienungsanleitung

ACME

ACME LED-0408 Bedienungsanleitung

ACME

ACME LP-F1000 CW Bedienungsanleitung

ACME

ACME LED-PS10 Bedienungsanleitung

ACME

ACME STAGE PAR 400 ZOOM IP Bedienungsanleitung

ACME

ACME XP-280 BS Bedienungsanleitung

ACME

ACME CB-16TC Bedienungsanleitung

ACME

ACME DOT Bedienungsanleitung

ACME

ACME LED-245/2 Bedienungsanleitung

ACME

ACME iSolution Bedienungsanleitung

ACME

ACME LED-MS600 PE Bedienungsanleitung

ACME

ACME LED-256D-10W Bedienungsanleitung

ACME

ACME COOLIE 14FC Bedienungsanleitung

ACME

ACME Solaris Bedienungsanleitung

ACME

ACME BOOTES Bedienungsanleitung

ACME

ACME DIABOLO 500 Bedienungsanleitung

ACME

ACME BRIGHT Bedienungsanleitung

ACME

ACME STORM Bedienungsanleitung

ACME

ACME LED-212RGB Bedienungsanleitung

ACME

ACME MP-12FC Bedienungsanleitung

ACME

ACME CM-150 PAGEANT 150 Bedienungsanleitung

ACME

ACME Diamonds II Bedienungsanleitung

ACME

ACME TOUR PIXEL BAR 1010 II Bedienungsanleitung

ACME

ACME Energy Spot PRO Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung