ACME Spartan Hybrid C Bedienungsanleitung

CONTENTS

1. Safety Instructions ......................................................................................... 2

2. Technical Specifications ................................................................................. 4

3. Control Panel ................................................................................................. 6

4. Color/Gobo and Lamp.................................................................................... 7

4.1 Color/Gobo .............................................................................................. 7

4.2 Light Source ............................................................................................. 7

4.3 Changing the Lamp .................................................................................. 8

4.4 Lamp Replacement Warning .................................................................... 9

5. How To Set The Unit....................................................................................... 9

5.1 Main Function.......................................................................................... 9

5.2 Home Position Adjustment .................................................................... 16

6. Control By Universal DMX Controller ........................................................... 19

6.1 DMX512 Connection.............................................................................. 19

6.2 Address Setting ...................................................................................... 20

6.3 DMX512 Configuration........................................................................... 21

7. Error Information......................................................................................... 36

8. Troubleshooting........................................................................................... 40

9. Fixture Cleaning ........................................................................................... 41

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will

not accept liability for any resulting defects or problems.

Unpack and check carefully that there is no transportation damage before using the unit.

This product is for indoor use only. Use only in a dry location.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.

DO NOT connect the device to any dimmer pack.

During initial start-up some smoke or smell may arise. This is a normal process and does not

necessarily mean that the device is defective, and it will decrease gradually within 15 minutes.

Make sure there are no flammable materials close to the unit while operating to avoid fire

hazard.

Examine the power wires carefully; replace them immediately if there is any damage.

Unit’s surface temperature may reach up to 90℃. DO NOT touch the housing bare-handed

during its operation.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut

Please read the instruction carefully which includes important information about

the installation, usage and maintenance.

off the mains power immediately.

DO NOT operate in dirty or dusty environment, do clean fixtures regularly.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together twist other cables.

The minimum distance between light output and the illuminated surface must be more than 18

meters.

Disconnect mains power before fuse/lamp replacement or servicing.

Replace fuse/lamp only with the same type.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance center if

needed.

Disconnect the mains power if the fixture is has not been used for a long time.

DO use the original packing materials before transporting it again.

Hot lamp explosion hazard. DO NOT open the unit within 15 minutes after switching off.

DO replace the bulb once it is damaged, deformed or life-expired.

DO NOT look directly at the light while the bulb is on.

Never touch bulb with bare fingers, as it is very hot after using.

DO NOT start on the unit without bulb enclosure or when housing is damaged.

Installation:

The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of the

fixtures weight. Always use a safety cable that can hold 12 times of the weight of the fixture when

installing.

The equipment must be installed by professionals. It must be installed in a place where is out of the

reach of people and no one can pass by or under it.

2. Technical Specifications

Power Voltage:

AC 100~240V, 50/60Hz

Power Consumption:

660W

Light Source:

PHILIPS MSD Platinum 20 R

Color Temperature:

7800K

Zoom Range:

BEAM mode: 2°~7°

SPOT mode: 5°~32°

WASH mode: 8°~70°

Movement:

Pan: 540°

Tilt: 270°

Pan/Tilt Resolution: 16 bit.

Fixation: Tilt lock

Dimmer/Shutter:

Smooth dimming from 0-100%; outstanding variable speed strobe effect

Color Wheel:

1 x color wheel with 14 colors plus white with rainbow effect

Gobo Wheel:

1 x static gobo wheel with 18 gobos plus open

1 x rotating gobo wheel with 7 gobos plus open

Control:

DMX Channel: 28/24/21/20 channels

Protocols: DMX, RDM

Firmware Upgrade via DMX link

Construction:

Display: LCD display

Battery backup for user operation without connecting to the mains

Data In/Out : 3-pin and 5-pin XLR

Power In/Out: Power Connector in

Protection Rating: IP20

Features:

Linear motorized zoom

Motorized focus

2 x prisms: 8 facet + 16 facet, rotatable in both directions and overlayable

Independent frost effect

Dimension/Weight:

400x335x667mm, 27kgs

15.7"x13.2"x26.3"in, 59.5lbs

Photometrics Diagram:

3. Control Panel

1. Display: Shows the various menus and the selected functions

2. Button:

To enter into move backward or leave the menu

To go backward to move up in the menu

DOWN

To go forward to move down in the menu

ENTER

To perform the desired functions

3. BATTERY DISPLAY:

To show the battery status

4. DMX IN:

For DMX512 operation, use 5-pin XLR cable to link the unit and DMX controller

5. DMX IN:

For DMX512 operation, use 3-pin XLR cable to link the unit and DMX controller

6. DMX OUT:

For DMX512 operation, use 5-pin XLR cable to link the next units

7. DMX OUT:

For DMX512 operation, use 3-pin XLR cable to link the next units

8. POWER:

To connect to supply power

9. FUSE(T 10A):

Protect the unit from damage of over current

10. POWER SWITCH:

Turns On/Off the power

4. Color/Gobo and Lamp

4.1 Color/Gobo

DANGER!

Install the color wheel/gobo wheels with the device switched off only.

Unplug from mains before changing the color wheel/gobo wheels!

CAUTION: Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be

opened!

4.2 Light Source

PHILIPS MSD Platinum 20 R

Because of its high internal pressure, there might be a risk that the Discharge lamp

would explode during operation. The lamp emits intense UV radiation which is harmful

to the eyes and skin. The high luminance of the arc can cause severe damage to the

retina if you take a close look at the lamp.

To protect the lamp, always turn off the lamp first (via control panel or DMX controller)

and let the unit run at least five minutes to cool down before switching off the mains

supply. Never handle the lamp or luminary when it is hot.

Do not touch the bulb with bare hands. If this happens, clean the lamp with denatured

alcohol and wipe it with a lint free cloth before installation.

The lamp generates UV radiation. Never operate the lamp without appropriate shielding.

When lighting up, the lamp operates at high pressure and there is a slight risk of arc tube

rupture. The risk increases with age, temperature and improper handling of the lamp. Do not

use the lamp longer than its lifespan.

Make sure the lamp is located in the center of the reflector for the best projection.

4.3 Changing the Lamp

Attention: The entire light path and lens of the luminaire must be thoroughly cleaned before

changing the bulb.

Do not use this lamp more than 1500 hours, using the lamp any longer than its set life could

seriously damage your unit. Periodically checking the lamp running time, when the lamp reaches

the 1500 hour mark, or close to it, we strongly suggest you switch the lamp out. Reset the lamp

time after you have replaced the lamp.

To replace the lamp:

1. Ensure that the fixture is detached from power and has cooled down completely. It is a good

idea to allow the fixture to run for 10 minutes after the lamp has been turned off, so that the

cooling fans have time to works.

2. Loosen the screws on the head of the fixture and open the fixture head covers.

3. Unplug the leads of the lamp and lift the lamp out of its recess, disconnect the lamp and

connect a new lamp that must be the same type with the old one. And then place the new lamp

into the lamp recess.

Finally reinstall the head cover, fastening it securely before reapplying power.

Warning:

The installing direction of lamp:

4.4 Lamp Replacement Warning

When the lamp reaches 1200 hours of usage, the display will flash the message “Replace Lamp

Soon” for up to 5 minutes. During this period, the fixture will still work normally.

When the lamp reaches 1500 hours of usage, the display will flash the message “Replace Lamp

Now” for up to 10 minutes. After 10 minutes, the fixture will return to normal operation.

When the lamp is continuously used overtime, the display will flash the message “Lamp

Timeout Use, Replace Lamp Now” for up to 10 minutes. After 10 minutes, the fixture will return

to normal operation.

Attention: Damages caused by the failure to replace the bulb in time are not subject to warranty.

5. How To Set The Unit

5.1 Main Function

Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until

the required function is shown on the monitor. Select the function by the ENTER button. Use the

UP/DOWN button to choose the submenu, press the ENTER button to store and automatically

return to the last menu. Press the MENU button or let the unit idle 30 seconds to exit menu mode.

The main functions are shown below:

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME DIABOLO 500 Bedienungsanleitung

ACME

ACME SABER HYBRID PRO Bedienungsanleitung

ACME

ACME CM-150 PAGEANT 150 Bedienungsanleitung

ACME

ACME CP-18TC Bedienungsanleitung

ACME

ACME Thunderbreaker Bedienungsanleitung

ACME

ACME TV LIGHT PANEL 2000 Bedienungsanleitung

ACME

ACME CRUX Bedienungsanleitung

ACME

ACME IL-2420 II Bedienungsanleitung

ACME

ACME Ozone 3 Bedienungsanleitung

ACME

ACME iSolution Bedienungsanleitung

ACME

ACME XP-280 BS Bedienungsanleitung

ACME

ACME Splendor 220 II Bedienungsanleitung

ACME

ACME ENERGY HYBRID X-400 BSW Bedienungsanleitung

ACME

ACME LED-MS600 PE Bedienungsanleitung

ACME

ACME TOUR PIXEL BAR 1010 II Bedienungsanleitung

ACME

ACME LED-PS10D RGBW Bedienungsanleitung

ACME

ACME XP-5000WZ Bedienungsanleitung

ACME

ACME Spider FC Bedienungsanleitung

ACME

ACME ASTRO LED-256D Bedienungsanleitung

ACME

ACME Stag Par MP-200 Bedienungsanleitung

ACME

ACME LED-767 RGBW Bedienungsanleitung

ACME

ACME PIXEL LINE IP Bedienungsanleitung

ACME

ACME HYGIEA Bedienungsanleitung

ACME

ACME LS-1005 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung