ACME Pageant CM-200Z Bedienungsanleitung

CM-200Z

UserManual

Please read the instruction carefully before using

CONTENTS

1. Safety Instructions..........................................................................................2

2. Technical Specifications..................................................................................4

3. How To Set The Unit ......................................................................................4

3.1 Control panel............................................................................................4

3.2 Main Function...........................................................................................6

4. Control By Universal DMX Controller ..........................................................11

4.1 DMX 512 Connection .............................................................................11

4.2 Address Setting.......................................................................................12

4.3 DMX 512 Configuration..........................................................................13

5. Troubleshooting............................................................................................15

6. Fixture Cleaning............................................................................................16

1. Safety Instructions

WARNING

yPlease keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

yPlease unpack and check carefully there is no transportation damage before using the unit.

yBefore operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

yIt’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

yThe unit is for indoor use only. Use only in a dry location.

yThe unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

yPlease disconnect main power before replacement or servicing.

yPlease make sure there are no flammable materials close to the unit while operating as it is

fire hazard.

yPlease use safety cable when fixes this unit. DO NOT handle the unit by taking its head only,

but always by taking its base.

yMaximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is

higher than this.

yUnit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand

during its operation. Turn off the power and allow about 15 minutes for the unit to cool

down before replacing or serving.

yIn the event of serious operating problem, stop using the unit immediately. Never try to

Please read carefully the instruction, which includes important

information about the installation

usa

e and maintenance.

repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center. Always use

the same type spare parts.

yDO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

yDO NOT open the unit within five minutes after switching off.

yThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

Caution:

There are no user serviceable parts inside the unit. DO NOT open the housing or attempt

any repairs yourself. In the unlikely event your unit may require service, please contact your

nearest dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. And make sure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of

the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the

unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out

of the touch of people and has no one pass by or under it.

For 230V 50Hz power supply, maximum fixtures that can be connected on one power cable is 8;

For 120V 60Hz power supply, maximum fixtures that can be connected on one power cable is 4;

2. Technical Specifications

◇Compact design, fast and powerful LED moving beam wash

◇DMX512 Control with 14 channels mode

◇Perfect strobe with smooth dimming 0~100%

◇Outstanding color macro effect

◇Blue LCD display for easy navigation

◇Low heat with long life span for fixture and LEDs

◇Ideal for stage, theatre, TV studio, rental and discotheques

Input Voltage: AC 100V~240V, 50/60Hz

Power Consumption: 198W

LEDSources: OSRAM OSTAR RGBW 12 ×10W LED

Beam Angel: 10°~60°

Dimension: 263.3×183×340.4mm

Weight: 7.5Kgs

3. How To Set The Unit

3.1 Control panel

FrontView RearView

1. Display:

To show the various menus and the selected functions

LED:

2. POWER On Power On

3. DMX On DMX input present

Button:

4.MENU To select the programming functions

5.DOWN To go backward in the selected functions

6. UP To go forward in the selected functions

7. ENTER To confirm the selected functions

8. Fuse(T 6.3A):

Protect the unit from damage of the over-current.

9. POWERCON IN:

Connect to a socket (AC 100~240V, 50/60Hz) via the supplied mains cable.

10. POWERCON OUT:

Connect to supply power to the next unit.

11 DMX IN (3-pin XLR):

For DMX512 link, use 3-pin XLR cable to link the unit together.

12 DMX IN (5-pin XLR):

For DMX512 link, use 5-pin XLR cable to link the unit together.

13. DMX OUT (3-pin XLR):

For DMX512 link, use 3-pin XLR cable to link the next unit.

14. DMX OUT (5-pin XLR):

For DMX512 link, use 5-pin XLR cable to link the next unit.

3.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is showing on

the display. Select the function by the ENTER button and the display will blink. Use the DOWN and UP

button to change the mode. Once the required mode has been selected, press the ENTER button to setup,

to go back to the functions without any change press the MENU button again. Hold and press the MENU

button about one second or wait for one minute to exit the menu mode.

The main functions are showing below:

DMX Address

Select DMX Address, press the ENTER button to confirm, the present address will blink on the

display. Use the UP and DOWN button to adjust the address from 1to 512. Once the address

has been selected, press the ENTER button to setup, to go back to the functions without any

change press the MENU button again. Hold and press the MENU button about one second or

wait for one minute to exit the menu mode.

Dimmer curve

Select Dimmer curve, press the ENTER button to confirm, present mode will blink on the

display. Use the DOWN and UP button to select the Mode1, Mode 2,Mode 3 or Mode 4

mode. Once the mode has been selected, press the ENTER button to setup, to go back to the

functions without any change press the MENU button again. Hold and press the MENU

button about one second or wait for one minute to exit the menu mode.

Mode 1(Optically Linear): The increase in light intensity appears to be linear as DMX value is

increased.

Mode 2(Square Law): Light intensity control is finer at low levels and coarser at high levels.

Mode 3(Inverse Square Law): Light intensity control is coarser at low levels and finger at high

levels.

Mode 4(S-cure): Light intensity control is finger at low levels and high levels and coarser at

medium levels.

Pan Inverse

Select Pan Inverse, press the ENTER button to confirm, present mode will blink on the display.

Use the DOWN and UP button to select the Yes (pan inversion) or No (normal) mode. Once

the mode has been selected, press the ENTER button to setup, to go back to the functions

without any change press the MENU button again. Hold and press the MENU button about

one second or wait for one minute to exit the menu mode.

Tilt Inverse

Select Tilt Inverse, press the ENTER button to confirm, present mode will blink on the display.

Use the DOWN and UP button to select the Yes (tilt inversion) or No (normal) mode. Once

the mode has been selected, press the ENTER button to setup, to go back to the functions

without any change press the MENU button again. Hold and press the MENU button about

one second or wait for one minute to exit the menu mode.

Back Light

Select Back Light, press the ENTER button to confirm, present mode will blink on the display.

Use the DOWN and UP button to select the On (LED on) or Off (LED off) mode. Once the

mode has been selected, press the ENTER button to setup, to go back to the functions

without any change press the MENU button again. Hold and press the MENU button about

one second or wait for one minute to exit the menu mode.

White Balance

Select White Balance, press the ENTER button to confirm, present mode will blink on the

display. Use the DOWN and UP button to select the Red or Green, Blue. Once the mode has

been selected, press the ENTER button to setup, use the DOWN and UP button to adjust the

value (125~255). Once selected, press the ENTER button to setup, go back to the functions

without any change press the MENU button again. Hold and press the MENU button about

one second or wait for one minute to exit the menu mode.

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME Thunderroar Bedienungsanleitung

ACME

ACME CHIRON Bedienungsanleitung

ACME

ACME Theatre Spot 150 Bedienungsanleitung

ACME

ACME Solaris Bedienungsanleitung

ACME

ACME LED-256D-10W Bedienungsanleitung

ACME

ACME XP-280 BS Bedienungsanleitung

ACME

ACME SAMURAI SCAN 50 Bedienungsanleitung

ACME

ACME CA-DC6S Bedienungsanleitung

ACME

ACME CRUX Bedienungsanleitung

ACME

ACME RAYZOR HYBRID Bedienungsanleitung

ACME

ACME DOT Bedienungsanleitung

ACME

ACME LED-212RGB Bedienungsanleitung

ACME

ACME DIABOLO 500 Bedienungsanleitung

ACME

ACME CB-16TC Bedienungsanleitung

ACME

ACME Diabolo Bedienungsanleitung

ACME

ACME Thunderstruck LP-2304 Bedienungsanleitung

ACME

ACME TOUR PIXEL BAR 1010 II Bedienungsanleitung

ACME

ACME ICARUS 620 Bedienungsanleitung

ACME

ACME Xperior XP-380 BEAM IP F Bedienungsanleitung

ACME

ACME COOLIE 14FC Bedienungsanleitung

ACME

ACME ColorTec 250 LED-CC60 Bedienungsanleitung

ACME

ACME V-BOX Bedienungsanleitung

ACME

ACME LED-SC252 Bedienungsanleitung

ACME

ACME GEIST BSWF Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung