Advantech MIC-3612/3-BE Bedienungsanleitung

User Manual

MIC-3612/3-BE

MIC-3612/3-BE User Manual ii

The documentation and the software included with this product are copyrighted 2017

by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right

to make improvements in the products described in this manual at any time without

notice. No part of this manual may be reproduced, copied, translated or transmitted

in any form or by any means without the prior written permission of Advantech Co.,

Ltd. Information provided in this manual is intended to be accurate and reliable. How-

ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-

ments of the rights of third parties, which may result from its use.

Acknowledgements

PC-LabCard is a trademark of Advantech Co., Ltd. IBM and PC are trademarks of

International Business Machines Corporation.

MS-DOS, Windows®, Microsoft® Visual C++ and Visual BASIC are trademarks of

Microsoft® Corporation. Intel® and Pentium® are trademarks of Intel Corporation.

Delphi and C++ Builder are trademarks of Inprise Corporation.

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its products will be

free from defects in materials and workmanship for two years from the date of pur-

chase.

This warranty does not apply to any products which have been repaired or altered by

persons other than repair personnel authorized by Advantech, or which have been

subject to misuse, abuse, accident or improper installation. Advantech assumes no

liability under the terms of this warranty as a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous testing, most of

our customers never need to use our repair service. If an Advantech product is defec-

tive, it will be repaired or replaced at no charge during the warranty period. For out-

of-warranty repairs, you will be billed according to the cost of replacement materials,

service time and freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For example, CPU

speed, Advantech products used, other hardware and software used, etc.) Note

anything abnormal and list any onscreen messages you get when the problem

occurs.

2. Call your dealer and describe the problem. Please have your manual, product,

and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return merchandize

authorization) number from your dealer. This allows us to process your return

more quickly.

4. Carefully pack the defective product, a fully-completed Repair and Replacement

Order Card and a photocopy proof of purchase date (such as your sales receipt)

in a shippable container. A product returned without proof of the purchase date

is not eligible for warranty service.

5. Write the RMA number visibly on the outside of the package and ship it prepaid

to your dealer.

Part No. 2003361220 Edition 1

Printed in Taiwan May 2017

iii MIC-3612/3-BE User Manual

Declaration of Conformity

This product has passed the CE test for environmental specifications when shielded

cables are used for external wiring. We recommend the use of shielded cables. This

kind of cable is available from Advantech. Please contact your local supplier for

ordering information.

This product has passed the CE test for environmental specifications. Test conditions

for passing included the equipment being operated within an industrial enclosure. In

order to protect the product from being damaged by ESD (Electrostatic Discharge)

and EMI leakage, we strongly recommend the use of CE-compliant industrial enclo-

sure products.

FCC Class A

Note: This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Opera-

tion of this equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own expense.

FCC Class B

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful inter-

ference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interfer-

ence to radio or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This equipment has passed the FM certification. According to the National Fire Pro-

tection Association, work sites are classified into different classes, divisions and

groups, based on hazard considerations. This equipment is compliant with the speci-

fications of Class I, Division 2, Groups A, B, C and D indoor hazards.

MIC-3612/3-BE User Manual iv

Technical Support and Assistance

1. Visit the Advantech web site at www.advantech.com/support where you can find

the latest information about the product.

2. Contact your distributor, sales representative, or Advantech's customer service

center for technical support if you need additional assistance. Please have the

following information ready before you call:

–Product name and serial number

–Description of your peripheral attachments

–Description of your software (operating system, version, application software,

etc.)

–A complete description of the problem

–The exact wording of any error messages

Warnings, Cautions and Notes

Document Feedback

To assist us in making improvements to this manual, we would welcome comments

and constructive criticism. Please send all such - in writing to: support@advan-

tech.com

Packing List

Before setting up the system, check that the items listed below are included and in

good condition. If any item does not accord with the table, please contact your dealer

immediately.

Item XXXXXXXX

Box XXXXXXXXX

Warning! Warnings indicate conditions, which if not observed, can cause personal

injury!

Caution! Cautions are included to help you avoid damaging hardware or losing

data. e.g.

There is a danger of a new battery exploding if it is incorrectly installed.

Do not attempt to recharge, force open, or heat the battery. Replace the

battery only with the same or equivalent type recommended by the man-

ufacturer. Discard used batteries according to the manufacturer's

instructions.

Note! Notes provide optional additional information.

v MIC-3612/3-BE User Manual

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp

cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the equip-

ment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting

it fall may cause damage.

7. The openings on the enclosure are for air convection. Protect the equipment

from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source

to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be

opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service

personnel:

15. The power cord or plug is damaged.

16. Liquid has penetrated into the equipment.

17. The equipment has been exposed to moisture.

18. The equipment does not work well, or you cannot get it to work according to the

user's manual.

19. The equipment has been dropped and damaged.

20. The equipment has obvious signs of breakage.

21. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE

STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C

(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT

SHOULD BE IN A CONTROLLED ENVIRONMENT.

22. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY

REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE

RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES

ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.

23. The sound pressure level at theoperator's position accordingto IEC 704-1:1982

is no more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech

disclaims all responsibility for the accuracy of any statements contained herein.

MIC-3612/3-BE User Manual vi

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the products from

damage.

To avoid electrical shock, always disconnect the power from your PC chassis

before you work on it. Don't touch any components on the CPU card or other

cards while the PC is on.

Disconnect power before making any configuration changes. The sudden rush

of power as you connect a jumper or install a card may damage sensitive elec-

tronic components.

vii MIC-3612/3-BE User Manual

Contents

Chapter 1 General Information ............................1

1.1 Introduction ...............................................................................................2

1.2 Features....................................................................................................2

1.3 Specifications............................................................................................2

Chapter 2 Hardware Configuration......................3

2.1 Initial Inspection ........................................................................................4

2.2 Hardware Installation ................................................................................5

2.3 I/O Address...............................................................................................6

2.4 Board Layout: Dimensions........................................................................7

Figure 2.1 MIC-3612 board layout: Dimensions..........................7

2.5 Jumper Setting..........................................................................................7

2.5.1 How to set jumpers.......................................................................7

Figure 2.2 Jumper setting example .............................................7

2.5.2 Default Settings.............................................................................8

2.5.3 Terminator resistor setup (JP2~JP9)..........................................10

2.5.4 66MHZ_ENABLE pin Setup........................................................10

Chapter 3 Pin Assignment & Wiring..................11

3.1 Pin assignments......................................................................................12

3.1.1 RS-232 Mode..............................................................................12

Table 3.1: MIC-3612DB44 ConnectorPinAssignmentfor RS-232

Mode.........................................................................12

Table 3.2: RS232 Mode DB9 Male Connector Description.......12

Figure 3.1 MIC-3612 DB44 Connector RS-232 Mode...............13

3.1.2 RS-485 Mode..............................................................................13

Table 3.3: MIC-3612DB44 ConnectorPinAssignmentfor RS-485

Mode.........................................................................13

Table 3.4: RS-485 Mode DB9P Male Connector Description....13

Figure 3.2 MIC-3612 DB44 Connector RS-232 Mode...............14

3.1.3 RS-422 Mode..............................................................................14

Table 3.5: MIC-3612DB44 ConnectorPinAssignmentfor RS-422

Mode.........................................................................14

Table 3.6: RS-422 Mode DB9 Male Connector Description......15

Figure 3.3 MIC-3612 DB44 Connector RS-422 Mode...............15

Chapter 4 Register Structure .............................17

4.1 Register Structure ...................................................................................18

Table 4.1: BASE+2 (read) Interrupt status register (ISR)..........18

Table 4.2: Interrupt Source And Priority Level...........................18

Table 4.3: Transmit and Receive FIFO Trigger Table And Level

Selection...................................................................19

Table 4.4: ..................................................................................20

Table 4.5: ..................................................................................20

Table 4.6: ..................................................................................20

Table 4.7: ..................................................................................20

Table 4.8: Parity Selection.........................................................20

MIC-3612/3-BE User Manual viii

Chapter 1

1General Information

MIC-3612/3-BE User Manual 2

1.1 Introduction

The MIC-3612 is a 3U/6U sized 4-port RS-232/422/485 CompactPCI® Comm. Card,

serial communication cards which complies with PICMG 2.0 R2.1 CompactPCI spec-

ifications. All channels are addressed in a continuous 32 byte I/O block for simplified

software access. All channels may also share one PCI interrupt.

The MIC-3612 comes standard with 16C850 UARTs containing 128 byte FIFOs.

These upgraded FIFOs greatly reduce CPU overhead and are an ideal choice for

heavy multitasking environments.

1.2 Features

PCI Specification 2.1x compliant

Speeds up to 921.6 Kbps

16C850 UARTs with 128-byte standard

Standard Industrial 3U/6U sized CPCI Board size

I/O address automatically assigned by PCI Plug-and-Play

OS supported: Windows@98/2000/XP/7, Linux

Surge protection (2500VDC).

Space reserved for termination resistors (for RS-422/485)

Automatic RS-485 data flow control

1.3 Specifications

Bus Interface: CPCI bus specification 2.1x compliant

Bus controller: LCMXO2-4000HC-4FTG256I

Communication controller: 16C850

IRQ: all ports use the same IRQ assigned by PCI Plug-and-Play

Data bits: 5, 6, 7, 8

Stop bits: 1, 1.5, 2

Parity: none, even, odd

Surge Protection: 2500 VDC

Speed (bps): 50 ~ 921.6 K

Data signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND (for RS-232)

TX+, TX-, RX+, RX-, RTS+, RTS-, CTS+, CTS-, GND (for RS-422) DATA+,

DATA-, GND (for RS-485)

Power consumption:

Dimensions: 160 mm x 100 mm

Operating temperature: 0°C ~ 70°C (referring to IEC68-2-1, 2)

Operating Humidity:

5 ~ 95% Relative Humidity, non-condensing (referring to IEC 68-2-1, 2)

Operating Humidity:

5 ~ 95% Relative Humidity, non-condensing (referring to IEC 68-2-3)

Storage Temperature: -20 ~ 80°C

Typical MAX

+5V 220mA 285mA

+3.3V 100mA 200mA

+12v 60mA 80mA

Inhaltsverzeichnis

Andere Advantech PCI-Karte Handbücher

Advantech

Advantech PCI-1202 Bedienungsanleitung

Advantech

Advantech PCI-1730U Bedienungsanleitung

Advantech

Advantech PCN-6351 Series Bedienungsanleitung

Advantech

Advantech PCE-3132 Installations- und Betriebshandbuch

Advantech

Advantech PCIE-1763AH Bedienungsanleitung

Advantech

Advantech PCI-1761 Bedienungsanleitung

Advantech

Advantech ECU-P1706 Installations- und Betriebshandbuch

Advantech

Advantech PCI-1723 Bedienungsanleitung

Advantech

Advantech DVP-7020A Bedienungsanleitung

Advantech

Advantech PCM-3641I Installations- und Betriebshandbuch

Advantech

Advantech PCIE-1750U Bedienungsanleitung

Advantech

Advantech MIC-3758DIO Bedienungsanleitung

Advantech

Advantech PCIE-1760 Bedienungsanleitung

Advantech

Advantech PCI-1714UL Installations- und Betriebshandbuch

Advantech

Advantech DSPC-8661-PCXE Bedienungsanleitung

Advantech

Advantech PCIE-1765 Bedienungsanleitung

Advantech

Advantech PCA-6194 Bedienungsanleitung

Advantech

Advantech UNO-P166 Installations- und Betriebshandbuch

Advantech

Advantech PCI-1710U-DE Bedienungsanleitung

Advantech

Advantech PCI-1752 Bedienungsanleitung

Advantech

Advantech PCI-1602UP Bedienungsanleitung

Advantech

Advantech PCI-1736UP Bedienungsanleitung

Advantech

Advantech PCI-1724U Bedienungsanleitung

Advantech

Advantech PCI-1723 Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

Moxa Technologies

Moxa Technologies CP-102E Bedienungsanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung