Advantech PCI-1724U Bedienungsanleitung

PCI-1724U

14-bit, 32-ch, Isolated Analog

Output Card

User Manual

PCI-1724U User Manual ii

The documentation and the software included with this product are copy-

righted 2004 by Advantech Co., Ltd. All rights are reserved. Advantech

Co., Ltd. reserves the right to make improvements in the products

described in this manual at any time without notice. No part of this man-

ual may be reproduced, copied, translated or transmitted in any form or

by any means without the prior written permission of Advantech Co., Ltd.

Information provided in this manual is intended to be accurate and reli-

able. However, Advantech Co., Ltd. assumes no responsibility for its use,

nor for any infringements of the rights of third parties, which may result

from its use.

Acknowledgements

PC-LabCard is a trademark of Advantech Co., Ltd. IBM and PC are

trademarks of International Business Machines Corporation. MS-DOS,

Windows, Microsoft Visual C++ and Visual BASIC are trademarks of

Microsoft Corporation. Intel and Pentium are trademarks of Intel Corpo-

ration. Delphi and C++ Builder are trademarks of Inprise Corporation.

All other product names or trademarks are properties of their respective

owners.

Part No. 2003172400 1st Edition

Printed in Taiwan May 2004

iii

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its prod-

ucts will be free from defects in materials and workmanship for two years

from the date of purchase.

This warranty does not apply to any products which have been repaired or

altered by persons other than repair personnel authorized by Advantech,

or which have been subject to misuse, abuse, accident or improper instal-

lation. Advantech assumes no liability under the terms of this warranty as

a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous test-

ing, most of our customers never need to use our repair service. If an

Advantech product is defective, it will be repaired or replaced at no

charge during the warranty period. For out-of-warranty repairs, you will

be billed according to the cost of replacement materials, service time and

freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For

example, CPU speed, Advantech products used, other hardware

and software used, etc.) Note anything abnormal and list any

onscreen messages you get when the problem occurs.

2. Call your dealer and describe the problem. Please have your man-

ual, product, and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return

merchandize authorization) number from your dealer. This allows

us to process your return more quickly.

4. Carefully pack the defective product, a fully-completed Repair and

Replacement Order Card and a photocopy proof of purchase date

(such as your sales receipt) in a shippable container. A product

returned without proof of the purchase date is not eligible for war-

ranty service.

5. Write the RMA number visibly on the outside of the package and

ship it prepaid to your dealer.

PCI-1724U User Manual iv

This product has passed the CE test for environmental specifications

when shielded cables are used for external wiring. We recommend the use

of shielded cables. This kind of cable is available from Advantech. Please

contact your local supplier for ordering information.

Technical Support and Assistance

Step 1. Visit the Advantech web site at www.advantech.com/support

where you can find the latest information about the product.

Step 2. Contact your distributor, sales representative, or Advantech's cus-

tomer service center for technical support if you need additional

assistance. Please have the following information ready before

you call:

- Product name and serial number

- Description of your peripheral attachments

- Description of your software (operating system, version, appli-

cation software, etc.)

- A complete description of the problem

- The exact wording of any error messages

Packing List

Before setting up the system, check that the items listed below are

included and in good condition. If any item does not accord with the

table, please contact your dealer immediately.

Before you install your PCI-1724U card, please make sure you have the

following necessary components:

• 1 x PCI-1724U card

• 1 x Companion CD-ROM (DLL driver included)

• 1 x User Manual (this manual)

v Table of Contents

Contents

Chapter 1 Introduction ..................................................... 2

1.1 Features ............................................................................. 2

1.2 Applications ...................................................................... 3

1.3 Installation Guide .............................................................. 4

Figure 1.1:Installation Flow Chart ................................. 5

1.4 Software Overview............................................................ 6

1.5 Device Driver Programming Roadmap ............................ 7

1.6 Accessories........................................................................ 9

Chapter 2 Installation ..................................................... 12

2.1 Unpacking ....................................................................... 12

2.2 Driver Installation ........................................................... 13

Figure 2.1:Setup Screen of Automation Software ....... 13

Figure 2.2:Different Options for Driver Setup ............ 14

2.3 Hardware Installation ...................................................... 15

Figure 2.3:The Device Name Listed on the Dev. Mng 16

2.4 Device Setup and Configuration .................................... 17

2.4.1 Setting Up the Device .................................................. 17

Figure 2.4:The Device Manager Dialog Box ............... 17

2.4.2 Configuring the Device ................................................ 18

Figure 2.5:The Device Setting dialog box ................... 18

Figure 2.6:Device Name Appearing on the List .......... 19

Chapter 3 Signal Connections ........................................ 22

3.1 Overview ......................................................................... 22

3.2 Switch and Jumper Settings ........................................... 22

Figure 3.1:Card Conn., Jumper and Switch Locations 22

3.2.1 JP67 .............................................................................. 23

3.2.2 JP0~JP31 ...................................................................... 23

3.2.3 Setting the Time to Reset Analog Outputs .................. 24

3.2.4 Board ID setting ........................................................... 24

3.3 Signal Connections ......................................................... 25

3.3.1 Pin Assignment ............................................................ 25

Figure 3.2:I/O Conn. Pin Assg. for the PCI-1724U ..... 25

3.3.2 I/O Connector Signal Descriptions .............................. 26

Table 3.1:I/O Connector Signal Descriptions .............. 26

3.3.3 Analog Output Connection .......................................... 26

3.4 Field Wiring Considerations ........................................... 27

Appendix A Specifications ................................................. 30

A.1 Analog Output ................................................................. 30

A.2 General ............................................................................ 30

Appendix B Block Diagram............................................... 32

Appendix C Register Structure & Format....................... 34

PCI-1724U User’s Manual vi

C.1 Overview ......................................................................... 34

Table C.1:PCI-1724U Register Format (Part 1) .......... 34

Table C.2:PCI-1724U Register Format (Part 2) .......... 35

C.2 DAC Control Register-0x00............................................ 36

Table C.3:DAC Control Register Trigger .................... 36

C.2.1 D13~D0 ...................................................................... 36

C.2.2 REG1 (D15), REG0 (D14) .......................................... 36

Table C.4:Register Selection ....................................... 37

Table C.5:DAC Normal Mode Selection ..................... 37

C.2.3 D23~D16 ..................................................................... 37

Table C.6:Control Register .......................................... 37

Table C.7:Group GX Register ..................................... 37

Table C.8: Channel CX Register ................................. 38

C.3 Synchronous Output Cnt. Reg./DAC Ready Status-0x0439

Table C.9:Synchronous Output Cnt. Register/DAC

Ready Status Register ...................................... 39

C.4 Synchronous Output Trigger Register-0x0C................... 40

Table C.10:Synchronous Output Trigger Register ...... 40

C.5 Board ID-0x10................................................................. 41

Table C.11:Board ID Register ..................................... 41

Table C.12:Board ID .................................................... 41

Appendix D Calibration ..................................................... 44

D.1 Voltage Calibration Procedure ........................................ 45

Figure D.1:Click the Setup button to Launch the Device

Setting .............................................................. 45

Figure D.2:Click the Calibration Button to Launch the

Calibration ....................................................... 46

Figure D.3:The Start-Up Window of Offset Calib. ..... 46

Figure D.4:The Adjustment Process of Offset Calib. .. 47

Figure D.5:The Adjustment Process of Span Calib. .... 48

Figure D.6:Finish Calibration ...................................... 48

Figure D.7:Data will be Overwritten ........................... 49

D.2 Current Calibration Procedure ........................................ 49

Figure D.8:Click the Setup Button to Launch the Device

Setting .............................................................. 49

Figure D.9:Click the Calibration Button to Launch the

Calibration ....................................................... 50

Figure D.10:The Adjustment Process of Offset Calib. 51

Figure D.11:The Adjustment Process of Span Calib. .. 52

Figure D.12:Check the Analog Output Value ............. 52

Figure D.13:Finish Calibration .................................... 53

Figure D.14:Data will be Overwritten ......................... 53

CHAPTER

Introduction

This chapter gives background infor-

mation on the PCI-1724U.

Sections include:

• Features

• Applications

• Installation Guide

• Software Overview

• Device Driver Programming Road-

map

• Accessories

PCI-1724U User Manual 2

Chapter 1 Introduction

Thank you for buying the Advantech PCI-1724U. The PCI-1724U is an

isolated multiple channels analog output card for PCI bus, and each ana-

log output channel is equipped with a 14-bit, double-buffered DAC.

The PCI-1724U is an ideal solution for industrial applications where mul-

tiple analog output channels are required.

The following sections of this chapter will provide further information

about features of multifunction cards, a Quick Start for installation,

together with some brief information on software and accessories for the

PCI-1724U card.

1.1 Features

• 32 isolated analog output channels

• A 14-bit DAC is equipped for each of the analog output channels

• Flexible output range: ±10 V, 0 ~ 20 mA, 4 ~ 20 mA

(0~20mA, 4~20mA is selected by software, please refer to Appendix D

Calibration Utility.)

• Synchronized output function

• Output values kept after system hot reset

• Board ID

The Advantech PCI-1724U offers the following main features:

Flexible Voltage Output Range

The PCI-1724U provides a fixed voltage output range of ±10 V for a flex-

ible range that can be used for a many different applications. Users can

define the specific voltage output range and output data format via the

enclosed software utility and driver.

3 Chapter1

Keeps Output Values After System Reset

Users can independently set the 32 outputs to different ranges: ±10 V, 0 ~

20 mA or 4 ~ 20 mA, and all ranges are software selectable. When the

system is hot reset (power not shut down), the PCI-1724U can either

retain the last analog output values, or return to its default configuration,

depending on the jumper setting. This practical function eliminates dan-

gers caused by improper operation during unexpected system resets.

Board ID

The PCI-1724U has a built-in DIP Switch that helps define each card’s ID

when multiple PCI-1724U cards have been installed on the same PC

chassis. The board ID setting function is very useful when users build

their system with multiple PCI-1724U cards. With correct Board ID set-

tings, you can easily identify and access each card during hardware con-

figuration and software programming.

1.2 Applications

• Process control

• Programmable voltage source

• Programmable current sink

• Servo control

• Multiple loop PID control

Note: For detailed specifications of the PCI-1724U, please

refer to Appendix A, Specifications.

PCI-1724U User Manual 4

1.3 Installation Guide

Before you install your PCI-1724U card, please make sure you have the

following necessary components:

• PCI-1724U DA&C card

• PCI-1724U User’s Manual

• Advantech DLL drivers (Included in the companion CD-ROM)

• Wiring cable PCL-10162 (option)

• Wiring board ADAM-3962 (option)

• Personal computer or workstation with a PCI-bus slot (running Win-

dows 2000/95/ 98/ME/XP)

Some other optional components are also available for enhanced opera-

tion such as application software ActiveDAQ, GeniDAQ and other third-

party software packages

After you get the necessary components and maybe some of the accesso-

ries for enhanced operation of your PCI-1724U multifunction card, you

can begin the installation procedure. Figure 1-1 on the next page provides

a concise flow chart to give a broad picture of the software and hardware

installation procedures:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Advantech PCI-Karte Handbücher

Advantech

Advantech PCI-1762 Bedienungsanleitung

Advantech

Advantech EKI-6340 Series Bedienungsanleitung

Advantech

Advantech PCI-1751U Bedienungsanleitung

Advantech

Advantech PCI-1240 Bedienungsanleitung

Advantech

Advantech PCM-2312 Bedienungsanleitung

Advantech

Advantech PCI-1602UP Bedienungsanleitung

Advantech

Advantech PCIE-1824 Bedienungsanleitung

Advantech

Advantech PCIE-1761H Bedienungsanleitung

Advantech

Advantech MIC-3758DIO Bedienungsanleitung

Advantech

Advantech PCM-3641I Installations- und Betriebshandbuch

Advantech

Advantech PCI-1723 Installations- und Betriebshandbuch

Advantech

Advantech PCI-1752U Bedienungsanleitung

Advantech

Advantech MIC-3640 Bedienungsanleitung

Advantech

Advantech PCIE-1750U Bedienungsanleitung

Advantech

Advantech PCI-1752USO Installations- und Betriebshandbuch

Advantech

Advantech PCIE-1174 Bedienungsanleitung

Advantech

Advantech PCI-1711U Series Bedienungsanleitung

Advantech

Advantech PCI-1761 Bedienungsanleitung

Advantech

Advantech PCLS-848-P Bedienungsanleitung

Advantech

Advantech PCI-1680U Bedienungsanleitung

Advantech

Advantech PCIE-1802 Bedienungsanleitung

Advantech

Advantech PCI-1742U Bedienungsanleitung

Advantech

Advantech PCI-1710U Bedienungsanleitung

Advantech

Advantech PCI-1680U Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

Moxa Technologies

Moxa Technologies CP-102E Bedienungsanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung