Agilent Technologies E2960B Series Montageanleitung

Agilent E2960B Series

Hardware and Probing Guide



Notices

Nopartofthismanual maybereproduced

inany form or byany means (including

electronic storage and retrieval or transla-

tion into a foreign language) without prior

agreement andwritten consent fromAgi-

lentTechnologies,Inc.asgovernedby

United States and international copyright

laws.

PrintHistory

E2960-97001, October 2009

E2960-97000, September 2009

Trademarks

Windows2000®,WindowsXP®,and

Microsoft .NET Framework 1.1® are U.S.

registered trademarks of Microsoft Corpo-

ration.

Manual Part Number

E2960-97001

Edition

Sixth edition, February 2015

Available in electronic format only

Agilent Technologies, Inc.

1900 Garden of the Gods Road

Colorado Springs, CO 80907 USA

Warranty

The material contained in this docu-

ment is provided “as is,”andis sub-

ject to being changed, without notice,

in future editions. Further, to the max-

imum extent permitted by applicable

law, Agilent disclaims all warranties,

either express or implied, with regard

to this manual and any information

containedherein, includingbut not

limited to the implied warrantiesof

merchantability and fitness for a par-

ticular purpose. Agilent shall not be

liable for errors or for incidental or

consequential damages in connection

with the furnishing, use, or perfor-

mance of this document or of any

information contained herein. Should

Agilent and the user have a separate

written agreement with warranty

terms covering the material in this

document that conflict with these

terms, the warranty terms in the sep-

arate agreement shall control.

Technology Licenses

The hardware and/or software described in

thisdocument are furnished undera

license and may beused or copied only in

accordance with the terms of such license.

Restricted Rights Legend

Ifsoftware is for use inthe performance of

aU.S.Government prime contract orsub-

contract,Softwareis delivered and

licensedas“Commercialcomputer soft-

ware” as defined in DFAR 252.227-7014

(June 1995), or as a “commercial item” as

definedinFAR 2.101(a) or as “Restricted

computer software” as defined in FAR

52.227-19 (June 1987) or any equivalent

agency regulationor contract clause. Use,

duplicationor disclosureofSoftwareis

subject to Agilent Technologies’ standard

commercial license terms, and non-DOD

Departments and Agencies of the U.S.Gov-

ernment willreceive no greaterthan

Restricted Rights as defined in FAR

52.227-19(c)(1-2) (June 1987). U.S. Govern-

ment users will receive no greater than

Limited Rights as defined in FAR 52.227-14

(June 1987) or DFAR 252.227-7015 (b)(2)

(November 1995), as applicable in any

technical data.

Safety Notices

CAUTION

noticedenotes ahaz-

ard. It calls attention to anoperat-

ing procedure, practice, or the like

that, if not correctly performed or

adhered to, could result in damage

to the product or loss of important

data. Do not proceed beyond a

CAUTION

notice until the indicated

conditions are fully understood and

met.

AWARNINGnoticedenotesa

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly per-

formed or adhered to, could result

in personal injury or death. Do not

proceed beyond a WARNING

notice until the indicated condi-

tionsare fully understoodandmet.

CAUTION

WARNING

Safety Summary

Safety Symbols

on Instruments

General Safety

Precautions

The following general safety precautions must be observed during all

phases of operation of this instrument. Failure to comply with these

precautions or with specific warnings elsewhere in this manual violates

safety standards of design, manufacture, and intended use of the

instrument.

Agilent Technologies Inc. assumes no liability for the customer's failure to

comply with these requirements.

Before operation, review the instrument and manual for safety markings

and instructions. You must follow these to ensure safe operation and to

maintain the instrument in safe condition.

General

This product is a Safety Class 1 instrument (provided with a protective

earth terminal). The protective features of this product may be impaired if

it is used in a manner not specified in the operation instructions.

All Light Emitting Diodes (LEDs) used in this product are Class 1 LEDs as

per IEC 60825-1.

Environment

Conditions

This instrument is intended for indoor use in an installation category II,

pollution degree 2 environment. It is designed to operate at a maximum

relative humidity of 95% and at altitudes of up to 2000 meters.

Safety Symbol

Description

Indicates warningorcaution.Ifyou see this symbol on a product, you must

refertothe manualsforspecific WarningorCaution informationto avoid

personal injury or damage to the product.

Frame or chassis ground terminal. Typically connects to the equipment's

metal frame.

Indicates hazardous voltages and potential for electrical shock.

Indicates that antistatic precautions should be taken.

Indicateshot surface. Please donottouch.

Indicates laser radiation turned on.

CSAisthe Canadiancertification marktodemonstratecompliancewiththe

Safety requirements.

CE compliance marking to the EU Safety and EMC Directives.

ISM GRP-1A classification according to the international EMC standard.

ICES/NMB-001compliance markingtotheCanadianEMC standard.

Agilent E2960B Series Hardware and Probing Guide

Before Applying

Power

Ground the

Instrument

Do Not Operate in

an Explosive

Atmosphere

Do Not Remove

the Instrument

Cover

Environmental

Information

Refer to the specifications tables for the ac mains voltage requirements

and ambient operating temperature range.

Verify that all safety precautions are taken. The power cable inlet of the

instrument serves as a device to disconnect from the mains in case of

hazard. The instrument must be positioned so that the operator can easily

access the power cable inlet. When the instrument is rack mounted the

rack must be provided with an easily accessible mains switch.

To minimize shock hazard, the instrument chassis and cover must be

connected to an electrical protective earth ground. The instrument must be

connected to the ac power mains through a grounded power cable, with

the ground wire firmly connected to an electrical ground (safety ground)

at the power outlet. Any interruption of the protective (grounding)

conductor or disconnection of the protective earth terminal will cause a

potential shock hazard that could result in personal injury.

Do not operate the instrument in the presence of flammable gases or

fumes.

Operating personnel must not remove instrument covers. Component

replacement and internal adjustments must be made only by qualified

personnel.

Instruments that appear damaged or defective should be made inoperative

and secured against unintended operation until they can be repaired by

qualified service personnel.

Agilent E2960B Series Hardware and Probing Guide

Contents

Safety Summary

N5306A I/O Module

N5322A ExtendedInterface Module

N5309A Exerciser Card and Extension Card

N5309A Exerciser Card

N5309-66417 ExerciserExtension Card

N5323A Jammer Card

N5315 Solid Slot Interposer Card

N5316A Backplane Board for PCIe

Soft Touch Midbus Probes

Midbus2.0(FullSize)Probes

Overview and Configuration Support

Installation Instructions

Characteristics

Mechanical Design Considerations for Midbus 2.0 Probes

Electrical Design Considerations for the Midbus 2.0 Probes 50

N5328A Half Size Midbus Probe 62

SettingUp the Probe

FootprintPinoutoftheProbe

Mechanical Dimensions

Electrical Design Considerations for Midbus Probes

Midbus PlacementWithin SystemTopology

Load Model

Reference Clock Probe

Mechanical Design Considerations for the Reference Clock Probe

Electrical Design Considerations for the Reference Clock Probe

Agilent E2960B Series Hardware and Probing Guide

N4241F Flying Lead Probe

Resistor Dimensions

Lane Mapping

Important Points About Using N4241F

N4241Z ZIF Flying Lead Probe

N5426A ZIF Tip

N5426A ZIF Tip Dimensions

N5451ALongWired ZIF Tip

N5451A Long Wired ZIF Tip Dimensions

Trimming Log Wired ZIF Tip Resistor Leads

Soldering Resistors to Long Wired ZIF Tips

BreakingOff LongWiredZIF TipsfromPackagingStrip

ZIFFlyingLeadConnectiontoDUT

ZIF Tip Connection to Flying Lead

Soldering the ZIF Tip or Long Wired ZIF Tip into a DUT

Lane Mapping

102

Important Points About Using N4241Z

103

Index

Agilent E2960B Series Hardware and Probing Guide

Agilent E2960B Series

Hardware and Probing Guide

N5306A I/O Module

This chapter provides information on the N5306A I/O module used for

PCIe.

Trigger In/Out

LED Display

Analyzer Probe

Lane Status

Inter-Module (x16)

Ref Clk Output

10MH

Output

Self-Test Port

Figure1

N5306A I/O Module

As shown in Figure 1, the N5306A I/O module has the following

components:

•

LED Display— This component is used to display the diagnostic

information when fatal faults are discovered, and to indicate progress

during the bootstrap. If everything is working properly, then this

component displays the module number, such as 103.

•

10 MHz Output— This component is a reference clock, which is used

for generating timestamps in Protocol Analyzer. This component

delievers 10 MHz output.

•

Analyzer Probe— This component is used to connect the midbus probe

module connector with N5306A and N5307A (slot interposer card).

For complete information on midbus probe, refer to Agilent Soft Touch

Midbus Probe, User's Guide.



N5306A I/O Module

For information on plugging midbus probe module connector with

N5306A Analyzer Probe, refer to Agilent System Protocol Tester,

Installation Guide.

•

Self-Test Port— This component is a loopback board, and is used to

connect the midbus probe tip with N5306A. The one side of this

loopback board has a retainer for the probe, and the other side has the

connector for the self-test port. To verify if N5306A I/O module and

midbus probe are working properly, plug in this loopback board into the

self-test port and then watch the lane status.

•

Lane Status— This component has 18 LED bullets that displays the

status of the lane by using different colored bullets. Two bullets,

labelled A and B, indicate global status information. Different colors

used to indicate global status information are:

•

Grey — This colored bullet means system is not configured.

•

Red — This colored bullet means the speed is not detected or the

system is not configured.

•

Yellow — This colored bullet represents speed of 2.5 Gb/s

•

Green — This colored bullet represents speed of 5 Gb/s.

Other 16 LED bullets, labelled 0 to 15, indicate the status of each lane.

These bullets are:

•

Red — This colored bullets means that there are no signals or the

lane is electrically idle.

•

Orange — This colored bullet marks the presence of invalid signals

on the lane.

•

Green — This colored bullet means that the data on the lane is

deskewed.

•

Blinking Green — This colored bullet means that the data on the

lane is skewed. It corresponds to yellow in the Port Overview pane

in the Protocol Analyzer GUI.

•

Grey — This colored bullet means that the lane is not configured. For

example, if you are using x4 link width, then first four bullets of the

lane would be green and rest of the bullets would be grey colored

bullets.

•

Inter- Module (x16)

— This component is used to share information with

another N5306A I/O module in the same chassis. The features of this

component are not yet supported by the System Protocol Tester

platform.

•

Ref Clk Output— This components is a reference clock, which N5306A

use to process the data internally. This components delivers 100 MHz

output.

•

Trigger In/Out— This component is used to listen to external trigger in

from a different device or send external trigger out to another device.

Agilent E2960B Series Hardware and Probing Guide

N5306A I/O Module

The following figure shows meaning of the pins of the Trigger In/Out

component.

Figure2

Trigger In/Out Pins

The following are some important points about the Trigger In/Out

component:

•

The outputs circuitry is designed to work into open in order to fit to

the LA input that is typically in the K-ohms range.

•

Maximum trigger input voltage should not exceed 3.3 V.

•

Trigger Out and 10 MHz Out have nominal output level of 2.0 V after

20 ns minimum pulse width.

•

Minimum Trigger In duration is ~20 ns.

Use

trigger cable

to send or receive external trigger in and out events.

Do not directly touch any component on the I/O module. It may be hot.

Componentson the I/O module are sensitivetothe staticelectricity.Therefore, take

necessary anti-static precautions, such as wear a grounded wrist strap, to minimize

the possibility of electrostatic damage.

Agilent E2960B Series Hardware and Probing Guide 9

NOTE

WARNING

CAUTION

N5306A I/O Module

Agilent E2960B Series Hardware and Probing Guide

Inhaltsverzeichnis

Andere Agilent Technologies Laborausrüstung Handbücher

Agilent Technologies

Agilent Technologies 490 Micro GC Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7820A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Bravo Einrichtungshandbuch

Agilent Technologies

Agilent Technologies G1574A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 490 Bedienungsanleitung

Agilent Technologies

Agilent Technologies Genomic DNA ScreenTape System Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7000 Triple Quadrupole GC/MS Bedienungsanleitung

Agilent Technologies

Agilent Technologies Seahorse XFp Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1100 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 85038M Handbuch

Agilent Technologies

Agilent Technologies 1260 Infinity II Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7890A Betriebsanleitung

Agilent Technologies

Agilent Technologies 1260 Infinity II Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7200 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1260Infinity II Bio-inert FractionCollector Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5975 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7693A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Cryogenic Bedienungsanleitung

Agilent Technologies

Agilent Technologies G2916A Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfinityLab LC Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7500 ICP-MS Bedienungsanleitung

Agilent Technologies

Agilent Technologies Varian CP-8400 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6850 Series II Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5975 MSD Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung

Yamato

Yamato BM510 Bedienungsanleitung