Agilent Technologies InfinityLab LC Series Bedienungsanleitung

Agilent Technologies

Agilent InfinityLab LC Series

1260 Infinity II Fraction Collectors

Inlet / Waste Tubings Replacement

This technical note describes the installation of the inlet/waste tubing kit to a

1260 Infinity II Fraction Collector:

•Agilent InfinityLab LC Series 1260 Infinity II Preparative-Scale Fraction

Collector (G1364E)

•Agilent InfinityLab LC Series 1260 Infinity II Analytical-Scale Fraction

Collector (G1364F)

•Agilent InfinityLab LC Series 1260 Infinity II Bio-inert Fraction Collector

(G5664B)

Contents

Replace the Inlet/Waste Tubings 2

Replace the Valve to Needle Tubing 8

Replace the Inlet/Waste Tubings

For bio-inert modules use bio-inert parts only!

When • When contaminated, worn out or visibly damaged

•Typically once every year

Parts required p/n Description

Preparative-scale:

G1364-68605 Tubing Kit 40 – 100 mL/min, 1.2 mm ID

Standard tubing kit for Preparative Fraction Collector

G1364-68603 Tubing Kit 4 – 8 mL/min, 0.5 mm ID (OPTIONAL)

G1364-68604 Tubing Kit 15 – 40 mL/min, 0.8 mm ID (OPTIONAL)

Analytical-scale and bio-inert:

G1364-68602 Tubing Kit 1 – 5 mL/min, 0.25 mm ID

Standard tubing kit for Analytical and Bio-inert Fraction

Collector

G1364-68601 Tubing Kit 1 mL/min, 0.15 mm ID (OPTIONAL)

G1364-68603 Tubing Kit 4 – 8 mL/min, 0.5 mm ID (OPTIONAL)

Preparations • Position the transport unit of the fraction collector in the Home position.

•Remove all installed trays from the tray base.

•Position the transport unit of the fraction collector in the Change Parts

position.

•Turn OFF the instrument.

•Remove the rear end of the fraction collector’s waste tubing from the

waste container, unscrew the front end of the fraction collector’s inlet

tubing from the flow cell of the detector.

WARNING

Personal injury

Risk of personal injury caused by the needle arm movement.

➔Keep fingers away from the needle area.

1Locate the diverter valve with the finger tight fittings of the inner tubing kit.

2Unscrew the two finger-tight fittings of the inner tubing kit at the diverter

valve.

CAUTION

Liquid spills or fraction losses

Worn or damaged tubings can cause potential spills or lead to

fraction losses.

➔Explicitly follow the described installation procedures to

maximize the lifetime of inlet / waste tubing assembly and the

valve to needle tubing, and to avoid potential spills or fraction

losses.

➔Regularly inspect the tubings and exchange them if they are

worn out or show visible signs of damage.

NOTE

Connect the tubings as described in order to maximize their lifetime

and operating security.

3Unclip the inlet / waste tubing assembly from the leak adapter.

4Remove the outer tubing kit from the unions.

5Remove the leak adapter from the module housing.

6Remove the unions from the inner tubing kit.

7Remove the clip by pushing it down through the module housing.

8Remove the inner tubing kit by pulling it down through the opening in the

module housing.

9Slide in the new inner tubing kit from bottom to top (1.) and let the clip click

into position (2.).

10 Install the unions to the inner tubing kit.





11 Install the leak adapter to the module housing.

12 Connect the outer tubing kit to the unions.

13 Clip the inlet / waste tubing assembly into the leak adapter.

14 A color coded ring on one of the tubings and the valve body indicates, which

tubing belongs to which port.

15 Connect the finger-tight fittings of the inner tubing kit to the ports of the

diverter valve. The tubings must run into the ports of the diverter valve in

horizontal, parallel lines.

NOTE

The tubings must not be bent or twisted.

16 Connect the tubing with the label with the arrow (1) to the flow cell of the

detector. Insert the other tubing (2) into the waste container.

17 Re-install the tray(s) in the tray base.

18 Start the instrument.

19 Close the front cover.





Replace the Valve to Needle Tubing

For bio-inert modules use bio-inert parts only!

When • When contaminated, worn out or visibly damaged

•Typically once every year

Tools required p/n Description

8710-1534 Wrench, open end, 4 mm

8710-0510 Wrench open 1/4 — 5/16 inch

Parts required p/n Description

Preparative-scale:

G1364-68605 Tubing Kit 40 – 100 mL/min, 1.2 mm ID

Analytical-scale and bio-inert:

G1364-68602 Tubing Kit 1 – 5 mL/min, 0.25 mm ID

Standard tubing kit for Analytical and Bio-inert Fraction

Collector

G1364-68601 Tubing Kit 1 mL/min, 0.15 mm ID (OPTIONAL)

Preparations • Position the transport unit of the fraction collector in the Home position.

•Remove all installed trays from the tray base.

•Position the transport unit of the fraction collector in the Change Parts

position and turn off the instrument.

•It might be more convenient to remove the needle from its carrier before

unscrewing the needle tubing.

WARNING

Personal injury

Risk of personal injury caused by the needle arm movement.

➔Keep fingers away from the needle area.

1Locate the diverter valve with the finger-tight fittings of the valve to needle

tubing assembly.

2Unscrew the finger-tight fitting of the valve to needle tubing assembly at the

diverter valve.

CAUTION

Liquid spills or fraction losses

Worn or damaged tubings can cause potential spills or lead to

fraction losses.

➔Explicitly follow the described installation procedures to

maximize the lifetime of inlet / waste tubing assembly and the

valve to needle tubing, and to avoid potential spills or fraction

losses.

➔Regularly inspect the tubings and exchange them if they are

worn out or show visible signs of damage.

NOTE

Install the tubing as described to maximize its lifetime.

3Using the 4 mm wrench and the 5/16“ wrench for counter-holding, unscrew

the valve to needle tubing from the needle.

4Un-clip the tubing from the bottom of the needle carrier assembly.

5Slide the tubing through the hole in the needle carrier assembly (from

bottom to top) (1.) and out of the holder in the z-arm assembly (2.).





Andere Handbücher für InfinityLab LC Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Agilent Technologies Laborausrüstung Handbücher

Agilent Technologies

Agilent Technologies 2200 TapeStation Bedienungsanleitung

Agilent Technologies

Agilent Technologies G1701DA Bedienungsanleitung

Agilent Technologies

Agilent Technologies ZORBAX Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies IMG-500 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 55 AA Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1260 Infinity II Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfinityLab Poroshell 120 Bedienungsanleitung

Agilent Technologies

Agilent Technologies G5562A Einrichtungshandbuch

Agilent Technologies

Agilent Technologies GPC/SEC Bedienungsanleitung

Agilent Technologies

Agilent Technologies AriaMx Bedienungsanleitung

Agilent Technologies

Agilent Technologies TriScroll Exhaust Silencer Kit Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7683 Bedienungsanleitung

Agilent Technologies

Agilent Technologies ZORBAX RRHT Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8890 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7890 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies IDP3GBKIT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5100 ICP-OES Bedienungsanleitung

Agilent Technologies

Agilent Technologies 83620A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1200 series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1260 Infinity Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1290 infinity Bedienungsanleitung

Agilent Technologies

Agilent Technologies Nano Indenter G200 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7697A Installationshandbuch

Agilent Technologies

Agilent Technologies 6850 Series II Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung

Yamato

Yamato BM510 Bedienungsanleitung