Assa Abloy Corbin Russwin ED4000 Series Bedienungsanleitung

FM209 10/18

Installation Instructions

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Available on the following devices:

Rim

Mortise

SecureBolt

Concealed Vertical Rod

*Surface Vertical Rod

*Rod Guards Required (made by other manufacturers)

Exit Device

Delayed Egress

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

Delayed Egress

Installation Instructions

Exit Device

FM209 10/18

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

TOC Table of Contents

Panic and Fire Rated Devices ...................................3

End Cover and P.C. Board Assembly...............................4

Installation of End Cover Assembly to Device ........................5

Device Mounting ............................................6

Wiring Layout: Input/Output Wiring Descriptions ......................7

ElectroLynx Connector System for All Electrical Installation ..............8

Installing Delayed Egress Exit Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

M93 Monitor - Trim Actuated Single Pole Double Throw (SPDT) Switch ..... 10

Non-ElectroLynx Door Prep.................................... 11

Wiring Diagram - Single Door Exit Only ........................... 12

Wiring Diagram - Single Door With Remote Inputs & Monitoring Outputs .... 13

Wiring Diagram - Single Door Exit Only ........................... 14

Wiring Diagram - Single Door With Remote Inputs & Monitoring Outputs .... 15

Wiring Diagram - Mechanical Trim Entry with External Door Position Switch .. 16

Operating Instructions ....................................... 17

Additional Options.......................................... 18

Troubleshooting ........................................... 19

Delayed Egress

Exit Device

Installation Instructions

FM209 10/18

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

1 Panic and Fire Rated Devices

1. Check device for shipping damage prior to installation and make sure all parts are on hand.

2. Identify options provided with device.

3. Identify model, type and hand of trim if applicable (see exit device and trim instructions for reversing

hands).

4. Contact hardware supplier if device is damaged or missing parts.

A. Checklist

B. Required Components (Numbered list correlates with numbers in Figure 1)

C. Optional Components (Numbered list correlates with numbers in Figure 1)

1. Delayed Egress Exit Device

2. 24VDC UL Listed Regulated and Filtered Power Supply with Fire Alarm Interface (recommend

Securitron BPS 24-1 or 24-2 (UL294 Listed), depending on requirements). Power supply is NOT to

be used in UL603 Burglar Alarm System.

3. Power transfer UL or Ulc listed (2-10 wire depending on system)-Securitron (EPT) or equivalent.

4. Sign (MUST BE INSTALLED ON DOOR ABOVE DEVICE).

NOTE: The delayed egress system is to be installed in accordance with NFPA 101.

5. Remote Annunciator

6. Door Position Switch (DPS)

7. Standard Trim

8. Electriﬁed Trim

9. Device and Trim Cylinder

D. Electrical Speciﬁcations*

Input Voltage 24VDC (+/-10%)

Wire Size:

18 AWG Min (up to 100')

Signal or Control 22AWG Min

Power Consumption:

Standard Device - 500mA

Device with Electric Trim - 883mA

*Follow Local Electrical Codes for Wiring.

NOTE: Components shown do not reﬂect all possible applications.

Consult manufacturer for special applications.

Figure 1

PUSH UNTIL ALARM

SOUNDS. DOOR CAN BE

OPENED IN 15 SECONDS.

115 VAC

800 mA

60 Hz

Fire

Alarm

Circuit

Req’d

Delayed Egress

Installation Instructions

Exit Device

FM209 10/18

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

2 End Cover and P.C. Board Assembly

NOTES: • Factory keyed orders will be

shipped assembled.

• Prior to end cover assembly, device must

be cut to proper length to prevent damage to

circuit board. 36" Device cannot be ﬁeld cut. A

maximum of 6" can be cut from a 48" device.

1. Slide circuit board assembly into end cover.

Front of assembly must be pulled away from

cover to prevent damage to LED indicator

light. Housing assembly is in correct position

when LED can be inserted in lens cover on

end cover. (Figure 2)

2. Insert cylinder (mortise and collar) into end

cover with keyway horizontal and toward

closest end of end cover.

Activator Legs

Arming Switch Activator

Circuit Board End Cover

To Power

Transfer

To Device

Connections

Rear Cover End Cap

Cylinder Collar

(Order separately

when required)

1000-118-A02

(Order Separately)

End Cover

Ta bs

Lens Cover

Cylinder Nut

Activator

Legs

Arming Switch Activator

ORDER SEPARATELY

1-1/2"

(38)mm

Dia.

Collar

Typical Mortise Cylinder

1000-118-A02 A02 Cam

1-1/8"

(29)mm .733"

(19)

Cylinders and Collars

• Use standard 1-1/8" mortise cylinder

with A02 cam. Corbin Russwin #1000-

118-A02 collar is not required.

• Use Corbin Russwin collar 270F15 for

optional 1-1/4" long cylinder.

• Use Corbin Russwin collar 654F07 for

optional 1-1/2" long cylinder.

Circuit Board Assembly

Indicator Light (LED)

1-1/8" (29mm) Mortise Cylinder

Figure 2

3. Slide arming switch activator over cylinder

so activator legs are on each side of switch.

4. Secure parts in place with cylinder nut. Be

certain ﬂange on cylinder nut inserts into

arming switch activator to allow rotation of

activator.

5. Verify assembly by rotating key counter-

clockwise and clockwise. Key should move

freely and arming switch should trip for

both rotation directions. If key does not

rotate freely, verify cylinder nut is in correct

orientation. If arming switch does not trip,

activator legs on arming switch activator

can be bent to reduce or increase rotational

travel.

Delayed Egress

Exit Device

Installation Instructions

FM209 10/18

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

3 Installation of End Cover Assembly to Device

1. Turn end cover assembly over to circuit board

side.

2. Nuisance delay setting is factory preset for

three (3) seconds. If immediate initiation of

alarm sequence is desired when pushpad is

pressed, remove jumper J5. (Figure 3)

3. Reset delay setting is factory set for ten (10)

seconds. Remove jumper J8 for 20-second

reset.

Exit Device

To PowerTransfer

OptionalWires

Device Lock Assembly Harness

Connector J1

Plugs into device

Connector J2

To PowerTransf

Circuit Board

End Cover

Place connector

and excess wire

in this area.

Connector

To PowerTransfer

Device End View

Optional M91, M93

or Safe/Secure wire

(refer to wiring

diagram for wiring).

Figure 3

4. Slide end cover assembly into device,

making sure not to pinch or crimp wires.

5. Connect device lock assembly harness to

connector J1. Place wire connectors and

excess wire between end cover and P.C.

board. (Figure 3, Device End View)

6. Check all connections before proceeding.

7. Proceed to device mounting (see packed

instructions).

Delayed Egress

Installation Instructions

Exit Device

FM209 10/18

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

4 Device Mounting

1. Refer to installation instructions included with

device and trim for complete door and frame

preparations. Refer to template #T30890 for

wire access hole location.

2. Feed wires from power transfer through wire

access hole in door. (Figure 4)

3. When required, mount outside trim to door (see

trim installation instructions).

4. Mount device to door (see device installation

instructions).

LHR Installation Shown

End Clamp

PowerTransfer

Hinge

End Cover

Installed

Wire Nuts Included

(Recommended for use with

Transfer Hinges)

1. Strip Wire 1/2"

2. Tw istWire

3. Insert Wire

4. Tighten

Wire Access

1" (25mm) dia. hole on

same centerline as

device. Inside face only.

Connector J2

Disconnect for Wiring

to Power Transfer

5. Do not install end cap until device has

been wired and tested for operation

(Additional Options, Section 16).

6. Check mechanical operation and proceed

to wiring diagrams (Sections 10 through14).

NOTE: Wire nuts can be inserted into wire

access hole after making connections.

Quick disconnect can be used without

removing wire nuts.

Figure 4

Delayed Egress

Exit Device

Installation Instructions

FM209 10/18

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

5 Wiring Layout: Input/Output Wiring Descriptions

Pin Number Input/Output Wire Color Description Pin Number

1 Input Black 24VDC Power Supply (-Circuit Ground) 1

2 Input Red 24VDC Power Supply (+Positive) 2

3 Input Brown

Remote Reset Input - Momentary input from

key switch, pushbutton, etc. Will release device

for 20 seconds for egress or ingress and also

reset device when in bypass or alarmed state.

4 Input Yellow

Remote Bypass Input - Momentary input from

key switch, pushbutton, etc. Will maintain device

in an unlocked state for normal device operation.

Device must be rearmed by resetting from

remote reset on device.

5Output Orange

Alarm Relay Output - Normally open contact

that changes to normally closed when device

alarm cycle has been activated.

6Output Blue

Alarm Relay Output - Normally closed contact

that changes to normally open when device

alarm cycle has been activated.

7Output Green

Secure Relay Output - Normally closed contact

that changes to normally open when device has

released.

8 Output White

Secure Relay Output - Normally open contact

that changes to normally closed when device

has released.

J2 Connector

(Figure 5)

ElectroLynx

Connector

NOTE:

• Pins 5-8 are negative (-) outputs. Use with LEDs and audibles (horns, sirens, etc.).

See wiring diagrams (Sections 9 through 14) for details.

• Cap all unused wires with enclosed wire nuts.

Old Board

New Board

Connector

To Device; Factory Wired

Black

Red

White

Blue

Brown

Orange

Ye llow

Violet

Negative

Positive

Remote Reset

Remote Bypass

Secure Relay Output (NO)

Secure Relay Output (NC)

Alarm Relay Output (NO)

Alarm Relay Output (NC)

Black

Red

Brown

Ye llow

Orange

Blue

Green

White

Negative

Positive

Remote Reset

Remote Bypass

Alarm Relay Output (NO)

Alarm Relay Output (NC)

Secure Relay Output (NC)

Secure Relay Output (NO)

Figure 5

Delayed Egress

Installation Instructions

Exit Device

FM209 10/18

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

6 ElectroLynx Connector System for All Electrical Installation

1. Mount exit device per instruction sheet provided.

2. Plug exit device connector into raceway connector in door. Feed through 1" (25mm) hole in door.

Install rail mounting end clamp bracket with two (2) screws supplied. Install end cap.

3. Plug raceway connector from edge of door into electric hinge connector and feed wires back

through door prep. Mount electric hinge to door.

A. If wiring now, wire frame side wires, to wires on pigtail harness, on hinge as required by using

connectors allowed by local code. Plug pigtail harness connector into electric hinge connector.

Feed harness through frame prep and mount electric hinge.

B. If wiring later, plug pigtail harness connector into electric hinge connector. Feed harness through

frame prep and mount electric hinge.

Installation Notes:

1. Wiring to pigtail harness is per facility wiring requirement.

2. For an ElectroLynx system, go to function or monitor page(s) with your device.

3. Combinations of certain monitors can be used in each device. These instructions detail installation

of each monitor separately.

ElectroLynx Connector System Notes:

System is designed to be installation friendly, with plug connectors from electric hinge through door

to device. The only wiring required is loose wires on pigtail harness assembly on frame side of electric

hinge (included with QC Hinge). Combinations of certain switches and monitors can be used.

The plug and receptacle connectors are designed to mate and lock together. Plug connectors into each

other with locking mechanism aligned. Do NOT force connectors together any other way.

Delayed Egress

Exit Device

Installation Instructions

FM209 10/18

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

8642

7531

Red +

Black -

White (NO Sec)

Green (NC Sec)

Orange (NO Alarm)

Blue (NC Alarm)

Brown (Remote Reset)

Ye llow (Remote Bypass)

8642

7531

Red + 2

Black - 1

White (NO Sec) 3

Green (NC Sec) 4

Orange (NO Alarm) 5

Blue (NC Alarm) 6

Brown (Remote Reset) 7

Ye llow (Remote Bypass) 8

Pigtail Harness

with 8-Pin Connector

(Provided with exit device)

Electric Hinge

with 8-Pin Connectors

Exit Device Connector

Raceway Harness with

8 & 4-Pin Connectors

(4-pin connectors are

not shown and are not

used)

Note: Typical raceway location

is shown.Other locations may

exist depending on door type.

7 Installing Delayed Egress Exit Device

Figure 6

Refer to Figure 6 for delayed egress exit device installation wiring.

NOTE: For ElectroLynx Hinge Connector System: Follow Section 6 wiring instructions.

For non-ElectroLynx door:

Remove connector at end of exit device and connect to incoming wires from power source using

wire nuts, butt splices, etc. See Section 9 for hole locations and sizes.

Delayed Egress

Installation Instructions

Exit Device

FM209 10/18

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

8 M93 Monitor - Trim Actuated Single Pole Double Throw (SPDT) Switch

Figure 7

Refer to Figure 7 for M93 Monitor - Trim Actuated SPDT Switch wiring.

NOTE:

• Switch contact rating: 5A @28VDC.

• Wire must be protected from abrasion.

• For use with Class II circuits only.

• For ElectroLynx Hinge Connector System: Follow Section 6 wiring instructions.

• For non-ElectroLynx door:

Remove connector at end of exit device and connect to incoming wires from power source

using wire nuts, butt splices, etc. See Section 8 for hole locations and sizes.

12 10

11 9

Gray

Pink

Ta n

8642

7531

Pigtail Harness

with 8-Pin Connector

(Provided with exit device)

Exit Device with

4 & 8-Pin Connectors

Raceway Harness with

8 & 4-Pin Connectors

(4-pin connectors are

not shown but are used)

Note: Typical raceway location

is shown.Other locations may

exist depending on door type.

D Function with M93 Monitor Exit

Device with 4-Pin Connector

Pigtail Harness

with 8-Pin Connector

(Wire colors have changed

for M93 monitor only)

Gray (C),10

Pink (NO), 11

Tan (NC), 12

Pigtail Harness

with 4-Pin Connector

or M93 monitor in combination

with other monitors or functions)

12 10

11 9

See Section 6 for

Wire Layout

See Section 6 for

Wire Layout

Andere Handbücher für Corbin Russwin ED4000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy RD150-3 Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON W91DCP Bedienungsanleitung

Assa Abloy

Assa Abloy CMD Bedienungsanleitung

Assa Abloy

Assa Abloy Rixson Smok-Chek VI Kurzanleitung

Assa Abloy

Assa Abloy DC 700G-FT BGS Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5400 FE Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 6332 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy 78PRA-8L Bedienungsanleitung

Assa Abloy

Assa Abloy Norton J1600 UniTrol Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1130 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC8210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SECURITRON DEM680E Series Handbuch

Assa Abloy

Assa Abloy Norton 5630 Series Kurzanleitung

Assa Abloy

Assa Abloy Norton 78-B/FHA Hold Open Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 3828 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5700 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1331 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YM Series Bedienungsanleitung

Assa Abloy

Assa Abloy Adams Rite EX89 Betriebsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC6210 Series Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung