Assa Abloy Corbin Russwin ED4000 Series Bedienungsanleitung

FM209 10/20

Installation Instructions

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Available on the following devices:

Rim

Mortise

SecureBolt

Concealed Vertical Rod

*Surface Vertical Rod

*Rod Guards Required (made by other manufacturers)

ED4000, ED5000 Series Exit Device

Delayed Egress

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

Delayed Egress

Installation Instructions

ED4000, ED5000 Series Exit Device

FM209 10/20

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

TOC Table of Contents

1 Panic and Fire Rated Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

a Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

b Required Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

c Optional Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

d Electrical Speciﬁcations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2 End Cover and PC Board Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

3 DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

4 Installation of End Cover Asssembly to Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

5 Device Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

6 Wiring Layout: Input/Output Wiring Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

7 ElectroLynx Connector System for All Electrical Installation. . . . . . . . . . . . . . . . . . . . . 10

8 ElectroLynx Wiring Options Overview with QC8 Hinge . . . . . . . . . . . . . . . . . . . . . . . . . 11

9 Installing Delayed Egress Exit Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

10 ElectroLynx Wiring Options Overview with QC12 Hinge. . . . . . . . . . . . . . . . . . . . . . . . 13

11 ElectroLynx Wiring Deed: M93 Trim Monitor Option and QC12 Hinge . . . . . . . . . . 14

12 ElectroLynx Wiring Deed: Electriﬁed Trim (ET) Option and QC12 Hinge . . . . . . . . . 15

13 ElectroLynx Wiring Deed: M91 Latchbolt Monitor Option and QC12 Hinge . . . . . 16

14 Non-ElectroLynx Door Prep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

15 Wiring Diagram: Single Door Exit Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Delayed Egress

Installation Instructions

FM209 10/20

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

ED4000, ED5000 Series Exit Device

TOC Table of Contents

16 Wiring Diagram: Single Door with Remote Inputs & Monitoring Outputs . . . . . . . 18

17 Wiring Diagram: M93 Trim Monitor Entry with External Door Position Switch . . 19

18 Wiring Diagram: 9903 Electrical Trim Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

19 Wiring Diagram: 9905 Electrical Trim Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

20 Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

21 Additional Options Non ElectroLynx Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

22 BOCA 15 Second Delay M89 & BOCA 30 Second Delay M90 . . . . . . . . . . . . . . . . . . . . 22

23 NFPA 101 Requirements: 30 Second Delay M88 Sufﬁx. . . . . . . . . . . . . . . . . . . . . . . . . . 22

24 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

25 Appendix: Legacy Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Delayed Egress

Installation Instructions

ED4000, ED5000 Series Exit Device

FM209 10/20

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

1Panic and Fire Rated Devices

1. Check device for shipping damage prior to installation and make sure all parts are on hand.

2. Identify options provided with device.

3. Identify model, type and hand of trim if applicable (see exit device and trim instructions for reversing

hands).

4. Contact hardware supplier if device is damaged or missing parts.

aChecklist

bRequired Components (Numbered list correlates with numbers in Figure 1)

cOptional Components (Numbered list correlates with numbers in Figure 1)

1. Delayed Egress Exit Device

2. 24VDC UL Listed Regulated and Filtered Power Supply with Fire Alarm Interface (recommend

Securitron BPS 24-1 or 24-2 (UL294 Listed), depending on requirements). Power supply is NOT to be

used in UL603 Burglar Alarm System.

3. Power transfer UL or ULC listed (2-10 wire depending on system)-Securitron (EPT) or equivalent.

4. Sign (MUST BE INSTALLED ON DOOR ABOVE DEVICE).

NOTE: The delayed egress system is to be installed in accordance with NFPA 101.

5. Remote Annunciator

6. Door Position Switch (DPS)

7. Standard Trim

8. Electrified Trim

9. Device and Trim Cylinder

dElectrical Speciﬁcations*

Input Voltage 24VDC (+/-10%)

Wire Size:

18 AWG Min (up to 100')

Signal or Control 22AWG Min

Power Consumption:

Standard Device - 500mA

Device with Safe/Secure Electric Mortise or

Electric Trim Control - 1.5A

*Follow Local Electrical Codes for Wiring.

NOTE: Components shown do not reﬂect all possible applications. Consult

manufacturer for special applications.

Figure 1

PUSH UNTIL ALARM

SOUNDS. DOOR CAN BE

OPENED IN 15 SECONDS.

115 VAC

800 mA

60 Hz

Fire

Alarm

Circuit

Req’d

Delayed Egress

Installation Instructions

ED4000, ED5000 Series Exit Device

FM209 10/20

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

2 End Cover and P.C. Board Assembly

NOTES:

• Factory keyed orders will be shipped assembled.

• Prior to end cover assembly, device must be

cut to proper length to prevent damage to

circuit board. 36" Device cannot be field cut. A

maximum of 6" can be cut from a 48" device.

1. Slide circuit board assembly into end cover.

Front of assembly must be pulled away from

cover to prevent damage to LED indicator

light. Housing assembly is in correct position

when LED can be inserted in lens cover on

end cover. (Figure 2)

2. Insert cylinder (mortise and collar) into end

cover with keyway horizontal and toward

closest end of end cover.

Activator Legs

Arming Switch Activator

Circuit Board

Label

To Power Transfer

To Device Connection

Circuit Boar

o Device

Figure 2

3. Slide arming switch activator over cylinder

so activator legs are on each side of switch.

4. Secure parts in place with cylinder nut. Be

certain flange on cylinder nut inserts into

arming switch activator to allow rotation of

activator.

5. Verify assembly by rotating key counter-

clockwise and clockwise. Key should move

freely and arming switch should trip for

both rotation directions. If key does not

rotate freely, verify cylinder nut is in correct

orientation. If arming switch does not trip,

activator legs on arming switch activator

can be bent to reduce or increase rotational

travel.

Delayed Egress

Installation Instructions

ED4000, ED5000 Series Exit Device

FM209 10/20

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

3DIP Switch Settings

* S2-8: When an external DPS is used and switch S2-8 ON, and 40 second reset delay (S2-4 and S2-5) are set

ON, after activation of momentary egress by cylinder key switch or external remote reset signal, if the Door/DPS

is open beyond 40sec the device will remain in momentary egress mode indefinitely and shall not enter alarm

mode; then once the Door/DPS is closed it will rearm immediately.

** With S2-8 OFF (S2-4 and S2-5 set for 5, 10, 20 or 40sec), if door/DPS is open after selected time the alarm will

sound. Close door to reset and rearm device using cylinder key or remote reset signal.

If door/DPS is opened then closed before selected time expires, the device will rearm immediately.

If DPS is not used, is bypassed with S2-7 ON, the door will rearm immediately after 5, 10, 20 or 40 sec whether

the door is open or closed, with either S2-8 ON or OFF.

Ensure eight S2 Dip Switches are set per application before moving on to the next page of instructions.

S2-1: Nuisance Audible may be selected ON (default) or OFF.

S2-2 and S2-3: Nuisance Delay time may be selected 0 (Im-

mediate), 1, 2, or 3 (default) seconds.

S2-4 and S2-5: Reset Delay time may be selected 5, 10 (de-

fault), 20 or 40 seconds.

S2-6: Whether an external LBM is used for not used for this

product, the switch must be set ON (default) to Bypass. S2-6

OFF position is not used.

S2-7: Switch must be set ON (default) to Bypass when an

external Door Position Switch (DPS) is NOT used, and OFF

when an external DPS is used.

Nuisance Audible

Nuisance Delay

(Special) RAC

Nuisance Delay

Reset Delay

LBM Bypass

DPS Bypass

Nuisance Delay (seconds)

0123

S2-2 OFF OFF ON ON

S2-3 OFF ON OFF ON

Reset Delay (seconds)

5102040

S2-4 OFF OFF ON ON

S2-5 OFF ON OFF ON

PCBA DIP SWITCH VIEW

Delayed Egress

Installation Instructions

ED4000, ED5000 Series Exit Device

FM209 10/20

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

4 Installation of End Cover Assembly to Device

1. Turn end cover assembly over to circuit board side.

2. Ensure eight S2 Dip Switches are set for application (see previous page).

3. Slide end cover assembly into device, making sure not to pinch or crimp wires.

4. Connect device lock assembly harness to connector J1. Place wire connectors and excess wire

between end cover and P.C. board. (Figure 3, Device End View)

5. Check all connections before proceeding.

6. Proceed to device mounting (see packed instructions). Figure 3

See DIP Switch settings on previous page

Connector J2

To power transfer

Connector J1

Plugs into device

Circuit Board

To Power Transfer

Device Assembly Harness

J5 detail view NO C NC for 2-pin jumper selection. NO is default position.

NOTE: Review J5 Alarm Relay NO or NC selection above. If NC contact is required, remove PBCA/cover

assembly from rail, move 2-pin jumper to NC, then re-install PCBA/cover on rail.

Delayed Egress

Installation Instructions

ED4000, ED5000 Series Exit Device

FM209 10/20

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

5Device Mounting

1. Refer to installation instructions included with device and trim for complete door and frame

preparations. Refer to template #T30890 for wire access hole location.

2. Feed wires from power transfer through wire access hole in door. (Figure 4)

3. When required, mount outside trim to door (see trim installation instructions).

4. Mount device to door (see device installation instructions).

5. Do not install end cap until device has been wired and tested for operation (See wiring diagrams).

6. Check mechanical operation and proceed to wiring diagrams.

NOTE: Wire nuts can be inserted into wire access hole after making connections. Quick disconnect can be used

without removing wire nuts.

NOTE: For QC8 and QC12 ElectroLynx wiring, refer to Sections 8 and 10. ElectroLynx has pluggable connectors,

wire nuts are not needed.

LHR Installation Shown

End Clamp

Power Transfer

Hinge

End Cover

Installed

Wire Nuts Included

(Recommended for use with

Transfer Hinges)

1. Strip Wire 1/2"

2. Twist Wire

3. Insert Wire

4. Tighten

Wire Access

1" (25mm) dia. hole on

same centerline as

device. Inside face only.

Connector J2

Disconnect for Wiring

to Power Transfer

Figure 4

Non-ElectroLynx Wiring

NOTES:

• Wires must be protected from abrasion.

• For use with Class II circuits only.

Delayed Egress

Installation Instructions

ED4000, ED5000 Series Exit Device

FM209 10/20

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

6Wiring Layout: Input/Output Wiring Descriptions

Pin Number Input/Output Wire Color Description Pin Number

10 Input Black 24VDC Power Supply (-Circuit Ground) 1

12 Input Red 24VDC Power Supply (+Positive) 2

11 Output White

Secure Relay Output - Normally Open (NO)

contact. Power off - contact is open

Powered/armed - Relay energizes contact

closes. After 15 or 30 seconds delay when

device releases, the relay de-energizes, contact

opens (same as Power off state).

13 Output Green

Secure Relay Output - Normally Closed (NC)

contact. Power off - contact is closed.

Powered/armed - Relay energizes, contact

opens. After 15 or 30 seconds delay when

device releases, relay de-energizes, contact is

closed (same as Power off state).

NC EGND Orange Earth Ground connection to PCB mounting plate

via ring terminal 5

3Output Blue

Alarm Relay Output - J5 jumper Selectable

NO/NC contact that changes state when alarm

cycle has been activated. Default shipped

position - jumper is on NO contact setting.

Power off - contact is NO or NC as per jumper

selection.Powered/armed - Relay energizes

contact reverses state. When alarm cycle is

activated - Relay de-energizes (same as Power

off state).

8 Input Brown

Remote Reset Input - Momentary input from

key switch, pushbutton, etc. Will release device

for 5, 10, 20, or 40 seconds for egress or

ingress and also reset device when in bypass or

alarmed state.

6 Input Yellow

Remote Bypass Input - Momentary input

from key switch, pushbutton, etc. Will maintain

device in an unlocked state for normal device

operation. Device must be rearmed by resetting

from key switch on device or remote reset.

J2 Connector

(See Figure 5 on next page)

8-Pin

ElectroLynx

Connector

NOTE: ElectroLynx QC8 Hinge is only required if all eight wires are used. When DPS and any

other wiring options are on the 4-pin connector, the hinge is NOT required.

NOTE: Secure and Alarm Relay contacts are rated max load 1A @24VDC.

Delayed Egress

Installation Instructions

ED4000, ED5000 Series Exit Device

FM209 10/20

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Figure 5

Pin Number Input/Output Wire

Color Description Pin Number

NC Input/Output Violet C, LBM or C, Trim Mon. or ET(-) 1

NC Input/Output Gray NO, LBM or NO, Trim Mon. or ET(+) 2

NC Input/Output Pink NC, LBM or NC, Trim Mon. 3

2 Input Tan Door Position Switch Input-Input sense for DPS

switch option

J2 Connector (See Figure 5 below.)

7 ElectroLynx Connector System for All Electrical Installation

1. Mount exit device per instruction sheet provided.

2. Plug exit device connector into raceway connector in door. Feed through 1" (25mm) hole in door.

Install rail mounting end clamp bracket with two (2) screws supplied. Install end cap.

3. Plug raceway connector from edge of door into electric hinge connector and feed wires back

through door prep. Mount electric hinge to door.

A. If wiring now, wire frame side wires, to wires on pigtail harness, on hinge as required by using

connectors allowed by local code. Plug pigtail harness connector into electric hinge connector.

Feed harness through frame prep and mount electric hinge.

B. If wiring later, plug pigtail harness connector into electric hinge connector. Feed harness through

frame prep and mount electric hinge.

NOTE: ElectroLynx QC12 Hinge is required if DPS and/or any options shown are required.

NOTE: Refer to Section 25 if replacing legacy PCBA/wiring with new PCBA/wiring.

Top View

Bottom

View

4-Pin ElectroLynx Connector

6Wiring Layout: Input/Output Wiring Descriptions, continued

Andere Handbücher für Corbin Russwin ED4000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy SW60 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC3210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 8800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5630 Series Kurzanleitung

Assa Abloy

Assa Abloy RIXSON SMOK-CHEK V 0101 Bedienungsanleitung

Assa Abloy

Assa Abloy Adams Rite EX88 Betriebsanleitung

Assa Abloy

Assa Abloy Norton 9300BCH Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT Powerglide 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Electroguard-59 80 Series Montageanleitung

Assa Abloy

Assa Abloy Norton 9510 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED8200A Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton Narrow Profile Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5400 FE Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7540ST Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-FMS Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC3200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 855 Montageanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-FMS Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9540 Series Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung