Assa Abloy Corbin Russwin ED8200A Series Bedienungsanleitung

FM124B 04/20

Installation Instructions

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

ED8200A Series

For Wood and Metal Doors

Fire-Rated Rim Exit Device

ED8200A Series

Installation Instructions

Fire-Rated Rim Exit Device

FM124B 04/20

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

1 Determine Hand of Door

IMPORTANT

• Failure to follow these instructions could affect

operation of this product and void warranty.

• Some trim designs are handed when used with this

device (see trim instructions).

• Exit devices must be securely fastened to properly

reinforced doors with fasteners which will not loosen or pull out. Add reinforcement when necessary.

• Before Installing:

• Be sure exit device is the proper hand for your door. (Figure 1)

• Use enclosed template to ensure proper operation.

Figure1

Push side

Pull sideLeft Hand

Reverse

Bevel Door

Right Hand

Reverse

Bevel Door

TOC Table of Contents

1 Determine Hand of Door ........................................................2

2 Package Contents ...............................................................3

3 Preparation .....................................................................3

a Mark Horizontal Centerline of Device ............................................3

b Install Trim (If Furnished) ........................................................3

c Cut Pushbar (If Required)........................................................4

4 Installation ......................................................................5

a Mount ED8200A Exit Device .....................................................5

b Install Strike .....................................................................6

c Install Front Bar Insert, Rear & Front Covers ......................................6

d Test Pushbar.....................................................................7

ED8200A Series

Installation Instructions

Fire-Rated Rim Exit Device

FM124B 04/20

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

2 Package Contents

ED8200A Qty. Description

Latch Assembly 6 #12-24 x 7/8" Phillips flat head machine screws

Rear Bracket 2

#12-24 x3/4" Phillips pan head machine screws, and #12 internal

washers (wood doors #12 x 1-1/4" Phillips pan head, type A, tapping

screws)

Strike, UL 4 #12-24 x 7/8" Phillips flat head machine screws

Front Bar Insert 1 #8-32 x 1" Phillips pan head machine screw

Rear Cover 1 #8-32 x 1" Phillips flat head machine screw with external washers

Front Cover 2 #8-32 x 1/2" Phillips flat head machine screw, type F, with external

washers

Non-Reinforced Door 4 #12-24 x 1-21/32" sex nuts

3 Preparation

a Mark Horizontal Centerline of Device

Establish a centerline of device by drawing a line across the door and the door stop, 40-5/16" (1.02 m)

above finished floor unless doors have been pre-prepped. (Figure 2)

b Install Trim (If Furnished)

See separate trim installation instructions.

Figure2

Of Device

Door

Finished

Floor Line

40-5/16"

(1.02 m)

Jamb

Of Strike

ED8200A Series

Installation Instructions

Fire-Rated Rim Exit Device

FM124B 04/20

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

3 Preparation (cont.)

c Cut Pushbar (If Required)

Note

If bar does not require cutting, proceed to step 4a.

A. Installation of device depends on trim: Note 3/4" (19 mm) minimum restriction. (Figure 3)

B. Measure and mark bar as shown. (Figure 4)

C. Fully depress bar and cut off square on mark. (Figure 5)

Figure3 Figure4

3/4" (19 mm) Min.

Cut off point

Door width minus

5" (127 mm)

Pushbar

must

be fully

depressed

Figure5

ED8200A Series

Installation Instructions

Fire-Rated Rim Exit Device

FM124B 04/20

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

4 Installation

a Mount ED8200A Exit Device

Installation of device depends on trim:

A. For Reinforced Metal Doors:

• For throughbolted trim in 2-1/8"prep, install device with two (2) fillister head screws (packed

with trim) in latch assembly holes marked D. (Figure 6)

For all other applications, install device with two (2) pan head machine screws and two (2)

internal tooth lock washers in latch assembly holes marked C.

• Use level as shown to ensure device is level. Use rear bracket to spot, drill, and tap two (2) rear

bracket mounting holes. Attach rear bracket to door using two (2) pan head machine screws and

two (2) lock washers. Drill, tap, and install four (4) flat head machine screws in latch assembly

holes marked E. (Figure 6)

B. For Un-Reinforced Doors Only:

• Using device as a template, drill 1/4"(6 mm) top and bottom latch assembly holes marked D

though door. Enlarge holes to 3/8"(10 mm) from opposite side of door to clear for sex nuts. Install

two (2) flat head machine screws and two (2) sex nuts. Drill and tap two (2) middle latch assembly

holes marked Eand install two (2) flat head machine screws (if applicable). (Figure 6)

C. For All Other Door Types:

• For throughbolted trim in 2-1/8"prep, install device with two (2) fillister head screws (packed

with trim) in latch assembly holes marked D. (Figure 6)

For all other applications, install device with two (2) pan head machine screws and two (2)

internal tooth lock washers and two (2) sex nuts in latch assembly holes marked C.

• Use level as shown to ensure device is level. Use rear bracket to spot and drill 1/4"(6 mm) holes

through door. Enlarge holes to 3/8"(10 mm) from opposite side of door to clear for sex nuts and

bolts. Attach rear bracket to door using two (2) pan head machine screws, two (2) lock washers,

and two (2) sex nuts. (Figure 6)

Figure6

Sex Nuts

Level

Rear

Bracket

Lock

Washer

Pan

Head

Machine

Screw

Flat Head Machine Screw

Of Device

Stop Line

Latch

Assembly

Sex Nuts

IMPORTANT

Maintain a 1/16" (2 mm) gap

between stop and latch frame.

ED8200A Series

Installation Instructions

Fire-Rated Rim Exit Device

FM124B 04/20

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

4 Installation (cont.)

b Install Strike

Install strike using flat head machine screws in

holes marked A. (Figure 7) Adjust strike. Strike is

properly adjusted when latch is able to fully project

when door is closed. Drill, tap, and install two (2) flat

head machine screws in holes marked B. (Figure 7)

Tighten all screws.

c Install Front Bar Insert, Rear & Front Covers

A. Slide front bar insert over end of front bar.

B. Assemble 1/2" pan head tapping screw through insert mounting hole.

C. While holding insert flush against back edge of front bar, tighten screw to bottom of recessed

mounting hole.

D. Install front and rear cover using 1" flat head screw with attached washer. (Figure 8)

Figure8

Flat Head

Machine

Screw

1" Flat Head Screw

with Attached Washer

1/2" Pan Head Tapping Screw

Front

Cover

Back

Edge

Assembled View

Front Bar

Front Bar Insert

Front Bar

Insert Rear

Mounting

Bracket

Rear Cover

Figure7

Flat Head

Machine

Screw

Strike

Shim Door

ED8200A Series

Installation Instructions

Fire-Rated Rim Exit Device

FM124B 04/20

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

d Test Pushbar

Latchbolt is retracted by pushbar inside. If latchbolt does not operate properly or does not remain secure,

inspect dimensions outlined in steps 3c, 4a, and 4c.

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group company.

without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Corbin Russwin, Inc.

225 Episcopal Road

Berlin, CT 06037 USA

Phone: 800-543-3558

Fax: 800-447-6714

www.corbinrusswin.com

FM124B 04/20

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy SARGENT 1431 Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 5200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SW60 Handbuch

Assa Abloy

Assa Abloy Norton 5700 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 1105 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED4000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 855 Montageanleitung

Assa Abloy

Assa Abloy Norton 78-B/FHA Hold Open Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9300BCH Bedienungsanleitung

Assa Abloy

Assa Abloy RD150-3 Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 278 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED159 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5400 FE Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy besam PUSH-N-GO Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED4000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy SECURITRON DEM680E Series Handbuch

Assa Abloy

Assa Abloy Norton 8000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Adams Rite EX76 Betriebsanleitung

Assa Abloy

Assa Abloy SARGENT Powerglide 281 Series Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung