Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

WARNING

This product can expose you to

lead which is known to the state of

California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.

P65warnings.ca.gov.

Attention Installer: Improper

installation may result in damage

to the product and void the factory

warranty.

WARNING

FM618 01/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

PED4000 / PED5000 Series with M61

Alarmed Exit Devices

Installation Instructions

FM618 01/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

PED4000 / PED5000 Series with M61

Installation Instructions

Alarmed Exit Devices

Tools Needed

The M61 Alarmed Exit is designed for areas that require an alarm to sound upon exiting. Once armed, any push rail

movement will activate the horn in the push rail. The horn will continue to sound for two minutes and then shut

off automatically. The LED will ﬂash indicating a violation has occurred.

Manual dogging is provided standard on

non ﬁre rated devices.

1” diameter hole(s) required for routing wires

into the door when remote option(s) is used.

• Installation must be performed by a trained service person.

• Basic installation is 9V alkaline battery operated. For hardwired option use 709F989 / 709F999 Wiring harness -

See instruction sheet included with kit.

• Field cut rail assemblies are not allowed. Exit device must be ordered from the factory for speciﬁc door width.

Notes:

General Description

FM618 01/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

PED4000 / PED5000 Series with M61

Installation Instructions

Alarmed Exit Devices

Miscellaneous Parts

End Cap

Mounting Plate

Rail Assembly

Alarm Insert Sub-Assembly

Chassis Cover

Chassis

FM618 01/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

PED4000 / PED5000 Series with M61

Installation Instructions

Alarmed Exit Devices

Door Preparation and Handing

Verify hand and bevel of door. Exit devices are always reverse bevel and are mounted on the

inside of the door.

PED5200 M61 RHRB

shown

Outside View Outside ViewInside View Inside View

Right Hand

Reverse Bevel

Hinges Right.

Open Outward

RHRB

Left Hand

Reverse Bevel

Hinges Left.

Open Outward

LHRB

PED5200 M61 LHRB

shown

Cylinder Installation or Replacement

Remove the battery and the battery box screws.

Disconnect the wire harness.

Note: If the cylinder is factory installed, go to Step 5 Installation Instructions (for retroﬁt kit) on page 6.

FM618 01/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

PED4000 / PED5000 Series with M61

Installation Instructions

Alarmed Exit Devices

Cylinder Installation or Replacement (continued)

CRemove the original cylinder (or foam plug, if

ordered without the cylinder):

a. Remove the battery box to expose the rear side

of the cylinder side. Use caution not to damage

any wire or switch when opening the battery

box as it is still connected to the assembly with

the battery terminal wires.

b. Remove the cylinder nut and switch actuator.

c. Remove the original cylinder (or foam plug).

Switch

Actuator

Cylinder

Nut

Cylinder (or foam plug)

Battery

Box

Install the new cylinder:

a. Install the new cylinder to the insert sub-

assembly with the keyway closest to the switch

end.

b. Reinstall the switch actuator with its legs on

opposite sides of the toggle switch on the

alarm board.

c. Reinstall the cylinder nut, then tighten.

d. Replace the battery box.

Switch

Actuator

Cylinder

Nut

Cylinder

Battery

Box

FM618 01/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

PED4000 / PED5000 Series with M61

Installation Instructions

Alarmed Exit Devices

Installation Instructions (for retroﬁt kit)

Connect the wire harness.

Reinstall the battery box screws and the battery.

Note: If M61 option was ordered on a full device, refer to those instructions for the device installation.

The following instructions are for alarm setup.

Cylinder Installation or Replacement (continued)

Remove the existing rail:

a. Remove chassis cover and end cap.

b. Loosen the chassis mounting screws.

c. Remove the end bracket.

d. Slide the rail assembly from the chassis.

Remove the mount rail and standard insert from

the push and carrier sub-assembly.

dMount Rail

Insert

FM618 01/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

PED4000 / PED5000 Series with M61

Installation Instructions

Alarmed Exit Devices

Installation Instructions (for retroﬁt kit, continued)

Ca. Insert the trigger mechanism arms to the gap

on both sides of the dogging cam (if present).

b. Slide the trigger mechanism forward into the

slot at the back of the dogging slope until it

clicks into place.

c. Press and release the push rail to verify that

the trigger is properly installed.

Slide the mount rail until it stops on the dogging

slope, then install the alarm insert sub-assembly

with the cylinder close to the push. Make sure

to press the switch ﬁrmly against the trigger

mechanism.

Mount Rail

Alarm Insert

Sub-assembly

Reinstall the rail:

a. Slide the rail assembly to the chassis.

b. Reinstall the end bracket.

c. Tighten the chassis mounting screws.

d. Reinstall the chassis cover and end cap.

Push Rail

Trigger Mechanism

Dogging slope

FM618 01/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

PED4000 / PED5000 Series with M61

Installation Instructions

Alarmed Exit Devices

To Arm Device Security / Tamper Violation

Low Battery Alert

Alarmed Exit (M61) Standard Operating Instructions

Turn the key clockwise. The LED will ﬂash yellow

(PASSAGE) for 15 seconds (default). A quick chirp will

sound and the LED will ﬂash green (ARMED) every 30

seconds. Signal indicates unit is armed.

NOTE: The unit is automatically armed 15 seconds

after the unit is turned on. Field selectable settings

listed on the next page.

When ARMED, depressing the push rail will activate

the alarm. The alarm will sound and the LED will ﬂash

red (VIOLATION). The alarm will continue for

2 minutes (default). After 2 minutes, the LED will

ﬂash red every 30 seconds until rearmed using the

key. Turn the key counter clockwise to deactivate the

alarm, then clockwise to rearm.

The alarm chirps intermittently to indicate low

battery. Change the battery.

Battery: 9 volt akaline battery

Yellow LED Green LED Red LED

FM618 01/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

PED4000 / PED5000 Series with M61

Installation Instructions

Alarmed Exit Devices

Optional Settings

DS3 DS4 Timer Reset

OFF OFF 2 minutes

OFF ON 5 minutes

ON OFF 10 minutes

ON ON Continuous*

These ﬁeld selectable switches can change the following functions:

Auto Alarm Reset

DS1 DS2 Timer Reset

OFF OFF 7 seconds

OFF ON 10 seconds

ON OFF 15 seconds

ON ON 20 seconds

DS5

ON GREEN/ARMED

RED/VIOLATION

YELLOW/ PASSAGE (DEFAULT)

OFF GREEN/VIOLATION

RED/ARMED

YELLOW PASSAGE

DS6*

ON Monitor relay is enabled (will activate when rail is violated)

*Requires 709F989 / 709F999 wire harness. See optional 709F989 / 709F999 wiring instructions for more information.

Recommend 3267 power supply and 546 wiring harness.

Request to Exit/

Passage Time Delay

FM618 01/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

PED4000 / PED5000 Series with M61

Installation Instructions

Alarmed Exit Devices

Andere Handbücher für Corbin Russwin PED5000 DB Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood 5831 Series Bedienungsanleitung

Assa Abloy

Assa Abloy MAB 609 + AC572 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC3210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6000 Series Installationshandbuch

Assa Abloy

Assa Abloy 5800 ADAEZ PRO Bedienungsanleitung

Assa Abloy

Assa Abloy Norton PR7500 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9510 Series Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON SMOK-CHEK V 0101 Bedienungsanleitung

Assa Abloy

Assa Abloy Crawford MCS-R Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5200 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC130 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7540STH Series Bedienungsanleitung

Assa Abloy

Assa Abloy ABLOY DA401 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SW200i Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7570 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7500H Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 6000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7540ST Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton UniTrol UNI-1600BC Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT FM8700 Bedienungsanleitung

Assa Abloy

Assa Abloy DC3210 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung