Assa Abloy SARGENT 351 Series Bedienungsanleitung

A7341B

express written permission of Sargent Manufacturing Company is prohibited.

1-800-438-1951 • www.sargentlock.com

Hold Open Arm Models

351 Series

Non Handed Door Closer

Standard Mount

Top Jamb Mount

Parallel Arm Mount

25-H

25-HZ

25-HZA

25-PH9

Adjustable (Sizes 1-6)

Ce produit peut vous exposer au plomb qui, dans l’état de la Californie,

est reconnu pour causer le cancer, des anomalies congénitales ou d’autres

problèmes de reproduction. Pour plus d’informations, visitez:

www.P65warnings.ca.gov.

This product can expose you to lead which is known to the state of

California to cause cancer and birth defects or other reproductive harm.

For more information go to www.P65warnings.ca.gov.

WARNING

Standard Mount

Closer mounts on hinge side of door

Top Jamb Mount

Closer mounts on frame of stop side of door

Parallel Arm Mount

Closer mounts on stop side of door

Legacy Friction Hold Open Arm

Right Hand Door - RH

Left Hand Door - LH

Right Hand Door - RHLeft Hand Door - LH

Note: Legacy FHO

arm has installation

orientation.

See 80-9300-0005-000,

available online.

Foot Bracket

Used with PH9

Parallel Arm Only

Right Hand Door - RH Left Hand Door - LH

Foot

Assembly

Main Arm &

Swivel Assembly

Swivel Arm

Screw

Foot

Dial

Dial Screw Arm

Mounting

Screw

Included Components

(See page 2 for mounting hardware)

H8 Mortise Friction Hold Open Arm

Note: H8 arm is handed same as door.

See template A7233, available online.

PH4 Friction Hold Open Arm

Note: PH4 parallel arm is used for

ush frame applications.

See template A7229, available online.

Screw

Pack

1/8" Hex

Wrench

To Determine Your Hand of Door:

To Identify Your Closer:

TO DETERMINE

HAND OF

YOUR DOOR:

LEFT

HAND

DOOR

RIGHT

HAND

DOOR

Right Hand

Reverse

Left Hand

Reverse

Tools Needed

Model ID:

+ = optional DA

Manufacture Date:

Week / Year

351 Case

Plastic or

Metal Cover

Removable

Insert

Approved 2020-01-21

A7341B

express written permission of SARGENT Manufacturing Company is prohibited.

1-800-438-1951 • www.sargentlock.com

• For special applications, a separate door and frame

preparation template is packed with these instructions. Use

this instruction sheet for installation sequence and closer

adjustments only.

• Doors should be hung on ball bearing or anti-friction hinges.

• A separate door stop is recommended.

• Always consult door/frame manufacturer for fastener compatibility.

• Door and frame must be properly reinforced.

• Adjust closing time speed between 3 and 6 seconds from 90°

to Close. Greater closing times may be required for elderly or

handicapped.

• DO NOT install closer on exposed side (weather side) of exterior

doors. Warranty will be void.

• Dimensions are given in inches (millimeters).

ATTENTION:

An incorrectly installed or improperly adjusted door closer can

cause property damage or personal injury. These installation

instructions should be followed to avoid the possibility of

misapplication or misadjustment.

351 Hold Open Closer

*Mounting Hardware Door or Frame Drill

Case, Foot or Optional PH9 Bracket:

#12 x 1-1/2 Phillips Flat Head Self Drilling

Tapping Screw Wood 3/32" (2.38mm)

Case, Foot or Optional PH9 Bracket:

#12 x 1-1/2 Phillips Flat Head Wood Screw

Case, Foot or Optional PH9 Bracket:

#12-24 x 5/8 Phillips Flat Head Machine

Screw

Metal Drill #16 (.177)

Tap 12-24

Case and/or Foot:

Mortise Nut

(optional)

Hollow Metal 1/4" (6.00mm) thru

3/8" (9.50mm) door face opposite to closer

Aluminum or Wood 3/8" (9.50mm) thru

Accessories

Mortise Nut and Screw Detail

Top jamb application: Door closer foot will be attached to the

door in a manner similar to that shown for mounting the case.

Appropriate mortise nuts and screws will be supplied based on

door thickness.

Door construction must provide a bridge type reinforcement to

prevent the door rail from collapsing when screws are tightened.

If distance between door stop and center of mortise nut head is

less than 7/8" (22mm), stop must be cut to clear head or head

must be recessed (shown).

* Security Torx screws supplied upon request, not shown

351A Mounting Plate

Allows mounting onto a door

with a minimum top rail of 2-3/8"

(60) or top jamb with 1-3/4" (44)

minimum frame clearance

351B Mounting Plate

Top Jamb Mount

For low ceiling conditions or

minimum 1-15/16" (49) frame face

351D Drop Plate

Parallel Arm Mount

For narrow top rail conditions

3" (76) minimum top rail required

Approved 2020-01-21

A7341B

express written permission of SARGENT Manufacturing Company is prohibited.

1-800-438-1951 • www.sargentlock.com

1. Prepare door and frame.

3a. Remove dial

from foot.

4. Connect arms, preload spring

and tighten screw.

3b. Install separate arms.

You’ve installed the 351 Hold Open Closer - Standard Mount.

🛑

Go to page 7 for closer adjustments and cover installation.

Dial DOWN

Left and Right Hand

RH and LH:

Position index at 2

1st

2nd

3rd

1st

3rd 2nd

Rotate elbow until

Foot Assembly arm

is perpendicular to

frame.

Rotating Main arm

preloads closer

spring power.

RH:

Clockwise

to tighten.

LH: Counter

clockwise to

tighten.

1st

3rd

2nd

5. Set Hold Open. Keep door open in position

until dial screw secures dial.

Arm Type Mounting Max Door

Opening **Dim A **Dim B

Holder

Standard 110° 9-1/2"

(241)

12-3/4"

(324)

Alternate *160° 6-1/2"

(165)

9-3/4"

(248)

NOTES:

1. IMPORTANT: Use Alternate mounting if door can open

beyond limits shown for standard mounting.

2. *If butt, frame, and wall conditions permit, door will open

180°.

3. ** Dimension is taken from hinge edge of door for

invisible hinges. Butt, offset, swing clear, center hung or

invisible hinges.

4. Use screws provided or use mortise nuts when required.

See chart on page 2.

2. Mount case to door.

Secure arms

with Swivel

Arm Screw.

LH and RH:

Spring Adjustment Screw AWAY from hinge

Closer is stamped RH at top for right hand

doors and LH at top for left hand doors.

351 Standard Mount - H Arm Installation

(Right Hand Shown)

Approved 2020-01-21

A7341B

express written permission of SARGENT Manufacturing Company is prohibited.

1-800-438-1951 • www.sargentlock.com

1. Prepare door and frame.

3a. Remove dial

from foot.

3b. Install separate arms.

You’ve now installed the 351 Hold Open Closer - Top Jamb Mount.

🛑

Go to page 7 for closer adjustments and cover installation.

Dial DOWN

Left and Right

Hand

RH and LH:

Position index at 2

5. Set Hold Open.

1st

3rd

Rotating Main

arm preloads

closer spring

power.

Keep door open in position

until dial screw secures dial.

3rd

1st

3rd

1st

2nd

RH:

Clockwise

to tighten.

LH: Counter

clockwise to

tighten.

2nd

4. Connect arms, preload spring

and tighten screw.

Arm Type Reveal

Depth

**Door

Opening

H Arm 0" to 2"

(0 to 51) 140°

HZ Arm 2-1/8" to 5"

(54 to 127) 140°

HZA Arm 5-1/8" to 8"

(130 to 203) 140°

NOTES:

1. * Dimension is taken from hinge edge of door for invisible hinges.

2. ** Door opening to 180° is possible if depth of reveal is not greater

than 2" (51).

3. 351A Mounting Plate required for double rabbeted frame.

4. Use screws provided or use mortise nuts when required. See chart on

page 2.

2. Mount case to frame. Use

Mounting Plate if necessary.

Secure arms

with Swivel

Arm Screw.

LH and RH:

Spring Adjustment Screw

AWAY from hinge

Closer is stamped RH at top

for right hand doors and LH

at top for left hand doors.

351 Top Jamb Mount - H, HZ, HZA Arm Installation

(Right Hand Shown)

2nd

Rotate elbow until

Foot Assembly arm

is perpendicular to

frame.

Approved 2020-01-21

A7341B

express written permission of SARGENT Manufacturing Company is prohibited.

1-800-438-1951 • www.sargentlock.com

1. Prepare door and frame.

Max Door

Opening **Dim A **Dim B

120° 9-7/8"

(251)

10-1/4"

(260)

*180° 7"

(178)

7-3/8"

(187)

NOTES:

1. *Do not use this mounting for swing clear hinges.

2. ** Dimension is taken from hinge edge of door for

invisible hinges.

3. Use screws provided or use mortise nuts when

required. See chart on page 2.

LH and RH:

Spring Adjustment Screw

AWAY from hinge

Closer is stamped RH at top

for right hand doors and LH

at top for left hand doors.

5. Install foot assembly to foot bracket

and case to door.

Dial DOWN

Left and Right Hand

3. Remove dial

from foot.

2. Close latching speed and

closing speed valves.

4. Install foot bracket to frame stop.

IMPORTANT

Latching

Speed

Closing

Speed

351 Parallel Arm Mount - PH9 Arm Installation

(Right Hand Shown)

6. Rotate bottom case spindle.

Wrench or main

arm may be used

to rotate spindle.

Approved 2020-01-21

A7341B

express written permission of SARGENT Manufacturing Company is prohibited.

1-800-438-1951 • www.sargentlock.com

You’ve now installed the 351 Hold Open Closer - Parallel Arm Mount.

🛑

Go to page 7 for closer adjustments and cover installation.

Closer will not operate

properly if main arm is

not indexed correctly.

8. Open latching speed and closing speed valves.

9. Connect arms, preload spring and

tighten swivel arm screw.

10. Set Hold Open.

Do not completely

open valves. Valves

will leak.

Arm under tension.

Keep ngers away

from moving parts.

1st

2nd

3rd

4th

Rotating arm

preloads closer

spring power.

Keep door open in position

until dial screw secures dial.

1st

3rd3rd

2nd

RH:

Clockwise

to tighten.

LH: Counter

clockwise to

tighten.

2nd

1st

2nd

RH: Position

index mark at 3

LH: Position index

mark at 1

Latching

Speed

Closing

Speed

351 Parallel Arm Mount - PH9 Arm Installation continued

(Right Hand Shown)

7. Attach Main arm as shown.

Approved 2020-01-21

A7341B

express written permission of SARGENT Manufacturing Company is prohibited.

1-800-438-1951 • www.sargentlock.com

Use provided 1/8" hex wrench to turn valves.

NEVER force valves out of closer.

NEVER completely close backcheck valve.

NEVER use backcheck as a door stop.

Closer Adjustments

Do not over tighten

cover screws.

Cover Attachment

Place removable

insert in unused

cover opening.

351 Hold Open Closer

Latching Speed

Backcheck

Closing

Speed

Delayed Action,

Optional

Number of Spring Power Nut Turns From Factory Setting

(Use as Guide ONLY)

Door Width Exterior Interior

Std/Top Jamb Parallel Std/Top Jamb Parallel

24" Factory Set 2-6 CW

1-5 CCW 1-5 CCW

30" 1-4 CW

32" 6-8 CW

36" 4-7 CW

40"

8-11 CW Factory Set

42" 7-10 CW Factory Set

44"

1-7 CW46" 10-12 CW 11-13 CW 1-5 CW

48"

over 48" up to 18 CW 5 CW & up 8 CW & up

Standard Mount shown

Parallel Arm Mount similar

Door must be open to adjust spring closing power.

Use 5/8" wrench or socket to turn screw. Refer to

chart. Do not use a power drill. Warranty will be

void.

Adjust closing time speed between 3 and 6 seconds

from 90° to Close. Greater closing times may be

required for elderly or handicapped.

If interior doors do not have to comply with

ADA requirements, exterior door settings are

recommended. Where strong drafts exist,

increase spring power as needed by turning spring

adjustment screw clockwise. If necessary, reduce

spring power by turning screw counter clockwise.

Top Jamb Mount

Insert

Approved 2020-01-21

A7341B

Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Patent pending and/or patent: www.assaabloydss.com/patents

SARGENT Manufacturing Company

100 Sargent Drive

New Haven, CT 06511 USA

800-727-5477

www.sargentlock.com

Approved 2020-01-21

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy SARGENT FM8700 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 278 Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-FMS Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5700 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7900H-B Series Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON 185 Quick Spotter Bedienungsanleitung

Assa Abloy

Assa Abloy effeff 828 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT Powerglide 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SW300 Handbuch

Assa Abloy

Assa Abloy Norton PR7500 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YM Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 78-B/FHA Hold Open Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC140 Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 6200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED8200A Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC700G-FT Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC3200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-S Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1331 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung