Assa Abloy Norton 5700 Series Bedienungsanleitung

whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9357-0140-020 Rev 3 09/19

5700 Series Power Operator Conversion

PUSH to PULL and PULL to PUSH Application

Patents: 5,881,497; 7,316,096; 7,484,333

5. Replace and tighten closer body screws.

6. Slide dip switch 1 on inverter from PUSH to PULL position.

Slide dip switch 2 from ON to OFF position. (Figure 4)

Note: Inverter Details located on page 3.

7. Turn on power to unit at On/Off switch and ip circuit

breaker to RESET position.

8. Immediately after activating unit, watch cam driver as

it rotates around. As soon as cam driver contacts pinion

extension, ip circuit breaker to OFF position. (Figure 3)

9. With door closed:

• Slide closed position magnet so it aligns with reed switch.

(Figure 5)

• Slide open position magnet so it is 180° from reed switch.

Slide magnet as needed to get proper door opening.

(Figure 5)

10. Flip circuit breaker to RESET position.

Pour la version francaise voir www.nortondoorcontrols.com.

READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.

This product can expose you to lead which is known to the state of

California to cause cancer and birth defects or other reproductive harm.

For more information go to www.P65warnings.ca.gov.

WARNING

Changing Operator From Push Side Unit to Pull Side Unit

1. Verify unit is congured for a push side application:

• Latch and Sweep valves are toward conduit holes. (Figure 2)

• Cam driver of clutch mechanism is toward conduit holes.

(Figure 3)

2. Turn off power to unit at On/Off switch and ip circuit breaker

to OFF position. (Figure 1)

3. Using a Phillips head screwdriver, remove four (4) closer body

screws and slide closer body away from clutch assembly.

(Figure 1)

NOTE: DO NOT remove pinion extension when removing

closer body. (Figure 3)

4. Orient closer body with BC valve toward conduit holes and slide

onto backplate so that pinion shaft of closer is inserted into

pinion extension of clutch assembly. (Figure 2)

NOTE: Some rotational adjustment of pinion extension may

be required to allow reassembly of closer pinion shaft and

pinion extension. Pinion at should remain opposite of

backplate for proper reassembly. (Figure 3)

Figure 1

Figure 2 Figure 3

Wiring not shown

Figure 4

Figure 5

whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9357-0140-020 Rev 3 09/19

5700 Series Power Operator - Conversion Instructions

Changing Operator From Pull Side Unit to Push Side Unit

Figure 6

Figure 7 Figure 8 Figure 9

Figure 10

5. Replace and tighten closer body screws.

6. Slide dip switch 1 on inverter from PULL to PUSH position.

Slide dip switch 2 from OFF to ON position. (Figure 9)

Note: Inverter Details located on page 3.

7. Turn on power to unit at On/Off switch and ip circuit

breaker to RESET position.

8. Immediately after activating unit, watch cam driver as

it rotates around. As soon as cam driver contacts pinion

extension, ip circuit breaker to OFF position. (Figure 8)

9. With door closed:

• Slide closed position magnet so it aligns with reed switch.

(Figure 10)

• Slide open position magnet so it is 180° from reed switch.

Slide magnet as needed to get proper door opening.

(Figure 10)

10. Flip circuit breaker to RESET position.

1. Verify unit is congured for a pull side application:

• BC valve is toward conduit holes. (Figure 7)

• Cam driver of clutch mechanism is away from conduit holes.

(Figure 8)

2. Turn off power to unit at On/Off switch and ip circuit breaker

to OFF position. (Figure 6)

3. Using a Phillips head screwdriver, remove four (4) closer body

screws and slide closer body away from clutch assembly.

(Figure 6)

NOTE: DO NOT remove pinion extension when removing

closer body. (Figure 8)

4. Orient closer body with latch and sweep valves toward conduit

holes and slide onto backplate so that pinion shaft of closer is

inserted into pinion extension of clutch assembly. (Figure 7)

NOTE: Some rotational adjustment of pinion extension may

be required to allow reassembly of closer pinion shaft and

pinion extension. Pinion at should remain opposite of

backplate for proper reassembly. (Figure 8)

Wiring not shown

whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9357-0140-020 Rev 3 09/19 3

5700 Series Power Operator - Conversion Instructions

Norton is a brand associated with ASSA ABLOY Accessories and Door Controls Group, Inc., an ASSA ABLOY Group company.

or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited. 80-9357-0140-020 Rev 3 09/19

Norton Technical Product Support:

Monroe, NC 28112 USA

Phone: 800.438.1951 ext: 6030

TechSupport.Norton@assaabloy.com

nortondoorcontrols.com

Andere Handbücher für Norton 5700 Series

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy Norton 7500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON SMOK-CHEK V 0101 Bedienungsanleitung

Assa Abloy

Assa Abloy Rockwood OH200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 6200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7970DPS-B Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 843G Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SW300 Bedienungsanleitung

Assa Abloy

Assa Abloy King 640 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-FMS Bedienungsanleitung

Assa Abloy

Assa Abloy SW200 Handbuch

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5900 Series Kurzanleitung

Assa Abloy

Assa Abloy Norton 8000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4600 A Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 351 POWERGLIDE Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED7400 Series Bedienungsanleitung

Assa Abloy

Assa Abloy MAB 609 + AC593 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6011 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Pull Side Series Kurzanleitung

Assa Abloy

Assa Abloy SARGENT FM8700 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung