Bradley 1WCA-BF Bedienungsanleitung
Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
+1 262 251 6000
www.bradleycorp.com
215-1775 Rev. C: ECO 21-03-013
© 2021 Bradley
Page 1 of 5 6/11/2021
Bradley Barrier-Free
1WCA-BF Wall Shower
Table of Contents
Pre-Installation Information ..........................2
Dimensions ......................................2
Installation Instructions ...........................3–4
Cleaning Instructions ...............................5
IMPORTANT
Read the entire installation manual to ensure proper installation of your 1WCA-BF wall shower. When
finished with the installation, file this manual with the owner maintenance department. Compliance and
conformity to local codes and ordinances is the responsibility of the installer.
Consult local building and plumbing codes prior to installation. Should these codes differ from the
information in the Manual, follow the local codes. Inquire with governing authorities for additional local
requirements.
This shower complies with most, but not all, ADA dimensional requirements. Check local codes prior to
installation. For ADA compliance use the 1WCA-ADA model.
Separate parts from packaging and make sure all parts are accounted for before discarding packaging
material. If any parts are missing, do not begin installation until you obtain the missing parts.
Product warranties may be found under "Products" on our website at bradleycorp.com
See separate installation sheets for information on the Wall Shower Diverter Valve Service Parts(215‑1369‑3a)
and Shower Hose Spray Repair Parts (215‑1369‑30).
2
1WCA-BF Barrier-Free Wall Shower Installation
6/11/2021 Bradley • 215-1775 Rev. C: ECO 21-03-013
Pre-Installation Information
Supplies required for installation:
• Water supply piping to connect 1/2" NPT flexible hoses
• Wall anchors and 1/4" diameter bolts for mounting top and bottom covers to wall
• Teflon tape or Teflon pipe dope
Overview
The 1WCA-BF Shower comes with your choice of valve: AST, EquaFlo™, EquaFlo HD, TTPA, TTPB, TMV, or Single
Valve with lever handle.
Components
Material: The shower body is constructed of 18 gauge, type 304 polished stainless steel. The shower caps are
constructed of 16 gauge stainless steel.
Supply Inlets: Supply inlets are 1/2" NPT flexible hose and are accessible through the back of the shower or through
knockouts on top shower cap.
Shower Spray Hose: The spray hose can be hand-held or mounted on the post on the shower body or optional slide
bar. The 60" (1524 mm) flexible spray hose is made of stainless steel.
Dimensions
Compliance and conformity to local codes and ordinance is the responsibility of the installer.
7½" (191)
4" (102)
6¼" (159)
6¾"
(171)
41½"
(1054)
42¼"
(1073)
43" (1092)
to floor
Centerline of
Valve
(mm)
3
Installation 1WCA-BF Barrier-Free Wall Shower
Bradley • 215-1775 Rev. C: ECO 21-03-013 6/11/2021
Step 2: Install Shower
1. Position the top cap of the shower on the wall and mark
the bolt hole locations on the wall.
2. Install wall anchors (supplied by installer) for 1/4" bolts at
the marked anchor hole locations.
3. Secure the top cap to the wall anchors with 1/4" bolts
(supplied by installer)
4. Connect the 1/2" flexible hose on the back of the shower
to the supply piping (piping is supplied by installer).
Supplies can be brought in through a knockout access
hole on the top or bottom caps.
For 1WCA-BF models with TTPA or TTPB valves, refer
to installation manual 215-1369-12 to make electrical
connections before continuing with installation.
5. Place body of shower over top cap.
6. Line up screw holes on top cap and shower body and
attach shower body to top cap with #10-24 screws
(provided).
7. Position bottom cap in shower body and attach bottom
cap to shower body with #10-24 screws (provided).
8. Secure bottom cap to wall with 1/4" bolts (supplied by
installer).
9. Turn on water to the unit to test the shower.
Installation
Flush the supply lines before making connections.
Supply inlets are 1/2" NPT flexible hose and are accessible through the back of shower (located 48" to 60"
above finish floor) or through knockouts on the top cap of shower.
Step 1: Rough In Piping
1. Rough-in the supply piping as required for your installation.
1/4" Bolts
(supplied by
Installer)
Top Cap
#10-24
Screw
Shower
Body
1/4" Bolts
(supplied by
Installer)
#10-24
Screw
Shower
Body
Outline of
Cap
Bottom
Cap
4
1WCA-BF Barrier-Free Wall Shower Installation
6/11/2021 Bradley • 215-1775 Rev. C: ECO 21-03-013
Step 3: Install Shroud (Optional)
Horizontal Shroud Installation
1. On a level line, position the bracket and slip ring in
place on the wall.
2. Secure the bracket and slip ring to the wall using 1/4"
diameter screws and anchors (supplied by installer).
3. Refer to the room layout and position the shroud in place
over the bracket and slip ring.
4. Secure the shroud to the bracket using the #10-24 x 1/2"
Allen screws (provided).
5. Using the shroud as a template, drill and tap #10-24 holes in
the slip ring using a #25 (.149) drill bit.
6. Secure the shroud to the slip ring using the #10-24 x 1/2"
screws (provided).
Vertical Shroud Installation
1. Position the slip ring against the ceiling and in line with
the shroud bracket that is mounted on the wall. Secure
the slip ring to the wall using 1/4" bolts and anchors
(supplied by installer).
2. With the bracket and slip ring secured, position the
shroud in place and secure the shroud to the shroud
bracket using the screws provided.
3. Using the holes at the top of the shroud as a template,
drill and tap #10-24 holes in the slip ring.
4. Secure the shroud to the slip ring using the #10-24
screws (provided),
Bracket
Slip Ring
12"
1"
8"
#10-24 Screw
6-1/2"
(165)
Slip Ring
3/4"
(19)
7-1/2"
(191)
#10-24
Screw
Shroud
#10-24
Screw
7-1/2"
(191)
4"
(102)
Shroud
Bracket
Shower
Body
4"
(102)
5
Installation 1WCA-BF Barrier-Free Wall Shower
Bradley • 215-1775 Rev. C: ECO 21-03-013 6/11/2021
Cleaning Instructions
Cleanliness is of utmost importance. Do not permit salty solutions to evaporate and dry on stainless steel.
Never use ordinary steel wool or steel brushes on stainless steel. Always use stainless steel wool or stainless
steel brushes.
1. Remove ordinary deposits of dirt and grease with soap and water. Whenever possible, the metal should be
thoroughly rinsed and dried after washing.
2. Use stainless steel polishing powder to get rid of tightly adhering deposits.
3. Look for the source of the rust in some iron or steel not actually a part of the stainless steel structure.
Sometimes the appearance of rust streaks on stainless steel leads to the belief that the stainless steel is
rusting. A steel nail or screw may be the cause of the trouble.
4. If the showerhead delivers an uneven spray, remove the showerhead from the unit, disassemble, and remove
foreign matter.
5. Reassemble showerhead and reinstall into unit.
Inhaltsverzeichnis
Andere Bradley Sanitärprodukte Handbücher
Bradley
Bradley Verge WashBar LVQ Series Bedienungsanleitung
Bradley
Bradley Sentry SN2004/IR Bedienungsanleitung
Bradley
Bradley Terreon TDWL22 Bedienungsanleitung
Bradley
Bradley 1C TouchTime Bedienungsanleitung
Bradley
Bradley Verge LVGD1 Bedienungsanleitung
Bradley
Bradley S19-230B Bedienungsanleitung
Bradley
Bradley Terrazzo WF2600 Series Bedienungsanleitung
Bradley
Bradley S19-260 Bedienungsanleitung
Bradley
Bradley Express SS Series Bedienungsanleitung
Bradley
Bradley Sentry SN2013/IR Bedienungsanleitung
Bradley
Bradley Equa-Flo Pressure Balancing Valve Bedienungsanleitung
Bradley
Bradley CRS Series Bedienungsanleitung
Bradley
Bradley Verge LVRD Series Bedienungsanleitung
Bradley
Bradley MG-2/BIR3 Bedienungsanleitung
Bradley
Bradley S19-120G Bedienungsanleitung
Bradley
Bradley HN-400 Bedienungsanleitung
Bradley
Bradley Verge LVRD Series Bedienungsanleitung
Bradley
Bradley S19-304GA Bedienungsanleitung
Bradley
Bradley E19-120A Bedienungsanleitung
Bradley
Bradley S19-120P Bedienungsanleitung
