Bradley Verge LVRD Series Bedienungsanleitung

Installation

P.O. Box 309

Menomonee Falls, WI 53052 USA

800 BRADLEY (800 272 3539)

+1 262 251 6000

bradleycorp.com

215-1708 Rev. J; ECN 16-08-008

Page 1 of 13 6/2/2016

LVRD1

Verge®Lavatory System – LVRD-Series

with Evero®Natural Quartz Material

Table of Contents

Components................................2–3

Supplies Required .............................4

Dimensions ................................4–5

Rough-Ins ...................................6

Frame Mounting...............................7

Faucet Box Mounting ...........................8

Drain Assembly ...............................9

Faucets and Optional Soap Valve .................9

Bowl Mounting ...............................10

Strainer and P-trap............................11

Adjust the Temperature ........................11

Trap Cover ..................................12

Cleaning and Maintenance .....................13

U.S. Pat. No. D629,877

WARNING

Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation.

Electrical power MUST remain off until installation is complete.

Installer’s hardware must be appropriate for wall construction. Wall anchors must have a minimum pull-out

rating of 1,000 lbs.

NOTICE

Make sure that all water supply lines have been flushed and then completely turned off before beginning

installation. Debris in supply lines can cause valves to malfunction.

IMPORTANT

Read this entire installation manual to ensure proper installation. When finished with the installation, file

this manual with the owner or maintenance department. Compliance and conformity to local codes and

ordinances is the responsibility of the installer. Product warranties may be found under “Products” on our

Web site at bradleycorp.com.

Separate parts from packaging and make sure all parts are accounted for before discarding any packaging

material. If any parts are missing, do not begin installation until you obtain the missing parts.

For standard height mounting, do not exceed the recommended 34" distance from the top of the lav deck

to the finished floor. To meet ADA requirements, the lav deck cannot exceed the 34" maximum height

dimension.

LVRD1 Installation

26/2/2016 Bradley • 215-1708 Rev. J; ECN 16-08-008

Components

TMV Valve

(½" NPTM

Outlet)

(S45-2701)

Frame

(S17-364)

Access Panel

(186-1857)

Hose Prepack

(S45-2730)

Supply

Fittings

(S45-2712)

Hose Prepack

(S45-2702)

TMV Supply

Connections

Tempered Supply

Connections

Complete Hardware Prepack (S45-2473)

Frame Mounting Qty.

Washer, Square 9 (4 extra)

Washer, Flat 1" O.D. 2

Bowl-To-Frame (S45-2481) Qty.

Screw, ¼-20 x ½" 3 (1 extra)

Washer, Flat ⁵⁄₈" O.D. 3 (1 extra)

Trap Cover (S45-2482) Qty.

Screw, 10-24 x ½" 6 (2 extra)

#10 Finishing Washer 6 (2 extra)

Trap Hook Bracket 1

Screw, 10-24 x 3⁄8" 1

Washer, Flat 35⁄64" O.D. 1

Bowl

Contact your Bradley Representative for color options

Complete Drain Prepack

(S45-2471)

Strainer and

Screw

(S45-2479)

O-Ring

(125-111)

Drain

Adapter

Packing

Washer

#10-24

Screw

Drain Adapter

Prepack

(S45-2480)

Chrome P-trap (S29-094)

Plastic P-trap (269-1697)

Plastic Hose

Plastic

Hose

Water supply to Battery Box Solenoid MUST be supplied

using a plastic hose (provided by Bradley).

Installation LVRD1

Bradley • 215-1708 Rev. J; ECN 16-08-008 6/2/2016 3

Components

IR-DCD Faucet*

(S53-336)

CAP-DCA Faucet**

(S53-334)

Battery Box Prepack

(S45-2508)

(includes bracket and

mounting hardware)

Battery Box for

CAP-DCA Faucets

6315-KT0000 Soap Dispenser 6324-68 Soap Dispenser 6334 Soap Dispenser

Optional

Transformer

Plug-In Transformer

Option (PT) for

IR-DCD Faucet

(S53-337)

Plug-in transformer option (PT)

includes Transformer (S53-338),

Adapter (S53-339), and Grounding

Kit (S53-349) for CAP-DCA Faucets

IR-DCG Faucet*

(S53-350)

Plug-In Transformer

Option (PT) for

IR-DCG Faucet

(153-486)

*Adapter included with faucet (TMV: S45-2872, TL: S45-2871) *Adapter included with faucet (TMV: S45-2872, TL: S45-2871)

**Adapter S45-2873 included with faucet

LVRD1 Installation

46/2/2016 Bradley • 215-1708 Rev. J; ECN 16-08-008

30"

(762mm)

20"

(508mm)

15⁄8" (41mm)

¼"

(6mm)

5⁄64"

(2mm)

13⁄16"

(30mm)

3⁄32" (2mm)

Drain inside dia.

15⁄16" (8mm)

LVRD Drain and Strainer —Close-up View

Dimensions

Top View

Front View

Supplies Required:

• (7)

3⁄8" lag screws, wall anchors, bolts (minimum pull-out rating of 1,000 lbs.)

• ½" hot/cold or tempered supply piping

• 1½" NPT drain piping

• OPTIONAL: 110 volt GFCI protected electrical outlet for 100–120 VAC plug-in transformer (for Bradley Faucets)

• Screen filter(s) as needed, if not included with faucet(s)

15"

(381mm)

7¾"

(197mm)

22½"

(572mm)

29"

(737mm)

Installation LVRD1

Bradley • 215-1708 Rev. J; ECN 16-08-008 6/2/2016 5

Dimensions – Side View

33½"

(851mm)

32½"

(826mm)

22½"

(572mm)

157⁄16"

(392mm)

159⁄16"

(395mm)

8½"

(216mm)

19"

(483mm)

30½"

(775mm)

29½"

(749mm)

22½"

(572mm)

157⁄16"

(392mm)

8½"

(216mm)

16"

(406mm)

28½"

(724mm)

29½"

(749mm)

22½"

(572mm)

157⁄16"

(392mm)

8½"

(216mm)

15"

(381mm)

30½"

(775mm)

22½"

(572mm)

157⁄16"

(392mm)

8½"

(216mm)

17"

(432mm)

31½"

(800mm)

Standard

Height

Juvenile

Height

TAS, Grades 6

through 8 or 9

TAS, Pre-K

through Grades

5 or 6 159⁄16"

(395mm)

159⁄16"

(395mm)

159⁄16"

(395mm)

LVRD1 Installation

66/2/2016 Bradley • 215-1708 Rev. J; ECN 16-08-008

Rough-Ins

33½"

(851mm)

Ref. B

31½"

(791mm)

217⁄8"

(556mm)

27¾"

(705mm)

307⁄8"

(784mm)

195⁄8"

(498mm)

Reinforce wall at points A and B.

Standard rough-in shown.

14½" (368mm)

to outside corner of bowl

RIM HEIGHT VERTICAL HEIGHT ADJUSTMENTS FOR CODES A–E and H FIXTURE STYLE

33½" None Standard Height

31½" Subtract 2" TAS, Grades 6 through 8 or 9

29½" Subtract 4" TAS, Pre-K through Grades 5 or 6

30½" Subtract 3" Juvenile Height

CODE DESCRIPTION QTY.

3⁄8

" Lav Deck Bowl Anchors with a Minimum Pull-Out Force of 1,000 lbs. (reinforce walls at anchor points) 2

3⁄8

" Lav Deck Frame Anchors with a Minimum Pull-Out Force of 1,000 lbs. (reinforce walls at anchor points) 5

H, C ½" Hot/Cold Supplies, Stub-Out 2" From Wall 1

D110v GFI Protected Electrical Outlet (AC version only) 1

E1½" NPT Drain, Stub-Out 2" from Wall 1

12½" (318mm) 12½" (318mm)

1½" (38mm)

4½"

(114mm)

1½" (38mm)

4½" (114mm) 27½"

(699mm)

247⁄8"

(632mm)

21⁄8"

(54mm)

2½"

(64mm)

15" (381mm)

to outside bottom corner of bowl

Installation LVRD1

Bradley • 215-1708 Rev. J; ECN 16-08-008 6/2/2016 7

1Frame Mounting

16"

(406mm)

centers

13"

(330mm)

Finished Floor

Drywall Drain, supplies and electrical box are

shown in their approximate locations.

Cut clearance holes in the backing as

required.

NOTE: Backing should equal the

thickness of the drywall (½" minimum).

The frame and

the bowl must

be adequately

supported.

Use 3⁄8" lag screws and square washers provided to secure the

frame to the backing (5) places. Shim frame as necessary.

NOTE: Other fasteners may be used based on wall material.

Support Backing Mounting Height "A" Dimension

Standard Height 19" (483mm)

TAS, Grades 6 through 8 or 9

17" (432mm)

TAS, Pre-K through Grades 5 or 6

15" (381mm)

Juvenile Height 16" (406mm)

If needed, shim the frame

at anchor points to ensure

the offset bracket is straight.

Leave the top screw loose.

11"

(279mm)

Typical installation is shown. It may be necessary to repair the wall

after mounting. The ﬁxture may not cover all of the wall modiﬁcations.

LVRD1 Installation

86/2/2016 Bradley • 215-1708 Rev. J; ECN 16-08-008

Mount the faucet box

onto the bracket with

valve positioned toward

the wall (if applicable).

Hang the faucet box bracket onto

the frame in the orientation shown.

Piping connection of box should

point toward the back of the unit.

2a Mounting Faucet Box to Frame

2b Mounting Valve to Frame

Cold

Hot

Optional TMA Valve

(½" NPTM Outlet)

Connect the faucet hoses. Attach the valve to

the back side of the frame member with the

(2) #10-24 self tapping screws provided.

TMA Option

NONE Option

A portion of the frame has been removed

from the view for clarity of valve installation.

Plastic Hose

Plastic

Hose

Water supply to Battery Box Solenoid MUST be supplied

using a plastic hose (provided by Bradley).

Installation LVRD1

Bradley • 215-1708 Rev. J; ECN 16-08-008 6/2/2016 9

4Faucets and Optional Soap Valve

3Drain Assembly

O-Ring

Drain Adapter

Packing Washer

#10-24

Screw

For ease of drain installation, lay the bowl on its back.

For ease of installation, leave the bowl laying on its back. Install the faucets and optional soap

valves according to manufacturer's instructions. Bradley Model 6315 Soap Dispenser is shown.

LVRD1 Installation

10 6/2/2016 Bradley • 215-1708 Rev. J; ECN 16-08-008

5a Bowl Mounting (to Frame)

Washer

¼"-20

Screw

5b Bowl Mounting (to Wall)

Reinforce behind the wall

at the two bowl mounting

locations, then secure the

bowl to the wall.

Press firmly on the back

of the bowl to seat the

bowl into the frame.

Tighten the top screw on

the frame.

Bowl is heavy!

Andere Handbücher für Verge LVRD Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley S19-220DCRPT Bedienungsanleitung

Bradley

Bradley EXPRESS SS-2/AST/JUV Bedienungsanleitung

Bradley

Bradley S19-270C Bedienungsanleitung

Bradley

Bradley Terreon Classic WF2500 Series Bedienungsanleitung

Bradley

Bradley S19-210FW Bedienungsanleitung

Bradley

Bradley S96-050 Bedienungsanleitung

Bradley

Bradley S19-465 Bedienungsanleitung

Bradley

Bradley Navigator S19-2010 Series Bedienungsanleitung

Bradley

Bradley S19-220FWPT Bedienungsanleitung

Bradley

Bradley S19-240 Bedienungsanleitung

Bradley

Bradley S19294 Series Bedienungsanleitung

Bradley

Bradley COMBI5500 Handbuch

Bradley

Bradley S19-220 Bedienungsanleitung

Bradley

Bradley Terreon Classic WF2500 Series Bedienungsanleitung

Bradley

Bradley Terreon Deep Bowl WF3200 Series Bedienungsanleitung

Bradley

Bradley Sentry SN2003/AST4 Bedienungsanleitung

Bradley

Bradley S19-310BF Bedienungsanleitung

Bradley

Bradley MG Series Bedienungsanleitung

Bradley

Bradley S19-270HD Bedienungsanleitung

Bradley

Bradley S19-220DCPT Bedienungsanleitung

Bradley

Bradley Terrazzo WF2600 Series Bedienungsanleitung

Bradley

Bradley Corner-Fount MF2922 Kurzanleitung

Bradley

Bradley Terreon Quadra-Fount MF2944/IR Bedienungsanleitung

Bradley

Bradley S19-630 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema