Bradley Express SS-3 Infrared-to-Touch Time Bedienungsanleitung

IMPORTANT

Read this entire installation manual

to ensure proper installation, then

file these instructions with the

owner or maintenance department.

Flush all the water supply lines

before making connections.

Wall anchors used must have a

minimum pull-out rating of 1,000

lbs.

Product warranties may be found

under "Product Information" on our

web site at www.bradleycorp.com..

SS-3/AST/WH97TAS

Express® Lavatory

System SS-Series

*Complies with Texas Accessibility

Standards (TAS) for Juvenile Height

applications.

Table of Contents

Pre-Installation Information . . . . . . . . . . . . . . . .2

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

Installation Instructions . . . . . . . . . . . . . . . . 5-11

Cleaning and Maintenance . . . . . . . . . . . . . . . .12

Soap Dispenser Maintenance . . . . . . . . . . .13-14

Check Valve Troubleshooting . . . . . . . . . . . . . .14

Assembly of Components . . . . . . . . . . . . . .15-16

Metering Air Valve Maintenance . . . . . . . . . . .17

Metering Air Valve Troubleshooting . . . . . .17-18

Vernatherm™ Thermostatic Mixing Valve . . . .19

P.O. Box 309, Menomonee Falls, WI 53052-0309

TEL. 1-800-BRADLEY FAX 262-251-5817

http://www.bradleycorp.com

215-1240 Rev. E; EN 08-805

Page 1 of 19 4/24/08

Installation

Instructions

OBSOLETE

Express® Lavatory System SS-Series

SS-3/AST/WH97TAS Installation - Obsolete

24/24/08 Bradley Corporation • 215-1240 Rev. E; EN 08-805

Pre-Installation Information

Texas Accessibility Standards compliant:

The SS-3/AST/WH97TAS Express® Lavatory System meets Texas Accessibility standards

(TAS) for barrier-free clearances, reaches and controls. Always check local codes and ordinances

for compliance.

Pushbutton and air valve

Each sprayhead is controlled by a pushbutton air valve, enabling each user to activate a single flow

of water. Air valves use 0.5 gpm for a ten-second duration, meeting the ANSI/ASHRAE/IES

90A-1980 Standard.

Supplies required for installation:

• (10) 3/8" wall anchors, bolts and washers to mount frame and bowl to wall

(minimum pull-out rating of 1,000 lbs.)

• 1/2" NPT hot and cold supply piping

• 1-1/2" NPT drain piping

Express® Lavatory System SS-Series

Installation - Obsolete SS-3/AST/WH97TAS

Bradley Corporation • 215-1240 Rev. E; EN 08-805 4/24/08

SS-3/AST/WH97TAS Express® Lavatory System Dimensions

Dimensions continue . . .

Express® Lavatory System SS-Series

SS-3/AST/WH97TAS Installation - Obsolete

44/24/08 Bradley Corporation • 215-1240 Rev. E; EN 08-805

Dimensions continued . . .

Juvenile Height

SS-3/AST/WH97TAS

Grades Pre-K thru 5 or 6

Juvenile Height

SS-3/AST/WH97TAS

Grades 6 thru 8 or 9

Express® Lavatory System SS-Series

Installation - Obsolete SS-3/AST/WH97TAS

Bradley Corporation • 215-1240 Rev. E; EN 08-805 4/24/08

Installation Instructions

Step 1: Rough in

Note: See Figure 1a (below) and Figures 1b and 2 (on page 6) when roughing in the Express®.

IMPORTANT: Flush the supply lines before making connections. Debris in supply

lines will cause the valves to malfunction.

IMPORTANT: Dimensions shown in Figure 1a are for Juvenile Height grades Pre-K

thru 5 or 6, and in Figure 1b for Juvenile Height grades 6 thru 8 or 9.

1. Rough in 1/2" NPT hot and cold supply lines through wall at dimensions shown.

2. Rough in 1-1/2" NPT drain waste connection through wall at dimensions shown.

3. Install (10) 3/8" wall anchors with a minimum pull-out rating of 1,000 lbs. (supplied by

installer) at the locations shown in Figures 1a and 1b.

NOTE: The anchors will be used to mount the Express® bowl and frame to the wall.

Figure 1a

Installation Instructions continue . . .

SS-3/AST/WH97 Express® Lavatory System Dimensions

Juvenile Height Mounting (Grades Pre-K thru 5 or 6)

Express® Lavatory System SS-Series

SS-3/AST/WH97TAS Installation - Obsolete

64/24/08 Bradley Corporation • 215-1240 Rev. E; EN 08-805

Installation Instructions continue . . .

Figure 1b

Figure 2

SS-3/AST/WH97 Express® Lavatory System Dimensions

Juvenile Height Mounting (Grades 6 thru 8 or 9)

Express® Lavatory System SS-Series

Installation - Obsolete SS-3/AST/WH97TAS

Bradley Corporation • 215-1240 Rev. E; EN 08-805 4/24/08

Installation Instructions continue . . .

Installation Instructions continued . . .

Step 2: Mount frame to wall

1. Remove the nine Torx-head screws securing the panel to the frame, and remove the panel

(see Figure 3).

2. Position the frame against the wall, ensuring that it is level.

IMPORTANT: Anchoring the frame to a wall that is not flat may cause the frame to

bend. If necessary, install shims to compensate for wall distortion.

3. Ensure that the back of the frame is flat against the wall. If wall is not flat, insert shims

behind the frame to ensure that it will not bend when anchored.

4. Once you have positioned the frame such that it is level and flat against the wall or shimmed,

use the 3/8" bolts and washers to mount the frame to the wall (see Figure 4).

Figure 3

(9) TORX-HEAD

SCREW

FRAME

PANEL

Figure 4

3/8" BOLTS

AND WASHERS

FRAME

Express® Lavatory System SS-Series

SS-3/AST/WH97TAS Installation - Obsolete

84/24/08 Bradley Corporation • 215-1240 Rev. E; EN 08-805

Installation Instructions continued . . .

Step 3: Install bowl assembly

IMPORTANT: Moving and positioning the bowl will require more than one person.

Note: Refer to Figure 5 below when installing the bowl assembly.

1. With someone to assist you, place the bowl assembly squarely onto the frame.

2. Attach the front of the bowl assembly to the frame using the four 1/4"-20 x 3/8" pan-head

screws and washers provided. Do not tighten screws at this time.

IMPORTANT: When bolting the bowl assembly to the frame and wall, do not

overtighten the bolts. Overtightening bolts can damage the

Terreon® material.

3. After the bowl assembly is attached to the frame, use two 3/8" bolts and washers (supplied

by the installer) to bolt the bowl to the wall anchors.

4. Tighten the screws installed in procedure #2 above to secure the bowl assembly to the frame.

Do not overtighten.

Installation Instructions continue...

Figure 5

BACK VIEW

Express® Lavatory System SS-Series

Installation - Obsolete SS-3/AST/WH97TAS

Bradley Corporation • 215-1240 Rev. E; EN 08-805 4/24/08

Installation Instructions continue . . .

Installation Instructions continued . . .

Step 4: Connecting supply

1. FOR HOT AND COLD SUPPLY: Connect the flexible hoses installed to the Vernatherm™

Mixing Valve to the hot and cold water supply piping from the wall (see Figure 6a).

Note: The red marking on Vernatherm™ Mixing Valve indicates hot water supply inlet.

FOR SINGLE TEMPERED SUPPLY: Attach the stop/strainer/check valve to the 1/2" tem-

pered supply line. Connect the flexible hose to the stop/strainer/check valve and air valve (see

Figure 6b).

Figure 6a

FLEXIBLE

SUPPLY

HOSE VERNATHERM™

THERMOSTATIC

MIXING VALVE

FLEXIBLE

SUPPLY

HOSE

CONNECT TO

1/2" NPT COLD

WATER SUPPLY

CONNECT TO

1/2" NPT HOT

WATER SUPPLY

Figure 6b

CONNECT E TO

TEMPERED

WATER SUPPLY

FLEXIBLE

SUPPLY

HOSE

CHECK VALVE

1/2 NIPPLE

(113-006DJ)

Express® Lavatory System SS-Series

SS-3/AST/WH97TAS Installation - Obsolete

10 4/24/08 Bradley Corporation • 215-1240 Rev. E; EN 08-805

Installation Instructions continued . . .

Step 5: Connecting plastic tubing

NOTE: Refer to Figure 7a for hot and cold supplies, and refer to Figure 7b for tempered supply.

1. Connect the plastic tubing for the water supplies from the sprayhead assembly to the quick-

connect fittings on the air valve as follows:

• insert the tubing with the red marking to the left valve

• insert the tubing with the black marking to the middle valve

• insert the tubing with the green marking to the right valve

IMPORTANT: The plastic tubing for the water supplies and pushbuttons are

pre-cut to the correct lengths. If the tubing is cut too short,

kinking can occur and cause leaks at the fitting locations.

2. Connect the plastic tubing for the pushbuttons from the sprayhead assembly to the quick-connect

fittings on the air valve as follows:

• insert the tubing with the red marking to the left valve

• insert the tubing with the black marking to the middle valve

• insert the tubing with the green marking to the right valve

3. Assemble the P-trap (supplied) and make drain connections.

AIR TUBING

(GREEN)

AIR TUBING

(RED)

AIR TUBING

(BLACK)

Figure 7b

Figure 7a VERNATHERM™

MIXING VALVE

FLEXIBLE

SUPPLY

HOSES

WATER SUPPLY

(BLACK)

WATER

SUPPLY

(GREEN)

AIR VALVE

WATER SUPPLY

(RED)

AIR VALVE

WATER

SUPPLY

(GREEN)

AIR TUBING

(GREEN)

AIR TUBING

(BLACK)

WATER SUPPLY

(BLACK)

WATER SUPPLY

(RED)

AIR TUBING

(RED)

FLEXIBLE

SUPPLY

HOSE

Andere Handbücher für Express SS-3 Infrared-to-Touch Time

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley S19-630 Bedienungsanleitung

Bradley

Bradley S19-120G Bedienungsanleitung

Bradley

Bradley S19-310BF Bedienungsanleitung

Bradley

Bradley S19-270C Bedienungsanleitung

Bradley

Bradley S19-690 Bedienungsanleitung

Bradley

Bradley S19-120 Bedienungsanleitung

Bradley

Bradley Advocate LA Series Bedienungsanleitung

Bradley

Bradley S96-051 Bedienungsanleitung

Bradley

Bradley S19-460 Bedienungsanleitung

Bradley

Bradley S19-310DCFW Bedienungsanleitung

Bradley

Bradley S19294 Series Bedienungsanleitung

Bradley

Bradley Express SS-3N/TT/STD Bedienungsanleitung

Bradley

Bradley S19-465EFW Bedienungsanleitung

Bradley

Bradley E19-310DC Bedienungsanleitung

Bradley

Bradley Sentry SN2003/AST4 Bedienungsanleitung

Bradley

Bradley FREQUENCY FL-1H Bedienungsanleitung

Bradley

Bradley Terreon TDB3103 Bedienungsanleitung

Bradley

Bradley S19-240 Bedienungsanleitung

Bradley

Bradley EXD-2N Bedienungsanleitung

Bradley

Bradley S19-220HFP Bedienungsanleitung

Bradley

Bradley S19-304GA Bedienungsanleitung

Bradley

Bradley Express MG Series Bedienungsanleitung

Bradley

Bradley S19-465EFW Bedienungsanleitung

Bradley

Bradley S19-220ABF Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema