Bradley MG Series Bedienungsanleitung

Installation

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 800.BRADLEY (800.272.3539) Fax: 262.253.4161

bradleycorp.com

215-1509 Rev. G; ECN 13-08-025

Page 1 of 19 4/9/2014

MG-3/BIR3

Express®

Lavatory System - MG

Series with Battery

Infrared Control

Table of Contents

Pre-Installation Information ..............2

Dimensions..........................3-4

Installation Instructions............... 5-11

Cleaning and Maintenance .............12

Assembly of Components ............13-15

Troubleshooting BIR3 Components .......16

Solenoid Valve Parts ..................17

Navigator®Valve Maintenance and Parts 18-19

Cleaning the Strainer ................18-19

IMPORTANT

Read this entire installation manual to ensure proper

installation.

Flush all the water supply lines before making connections.

Wall anchors used must have a minimum pull-out rating of

1,000 lbs.

File these instructions with the owner or maintenance

department.

Product warranties may be found under “Product

Information" on our web site at www.bradleycorp.com.

Express®Lavatory System - MG-Series with Battery Infrared Control

MG-3/BIR3 Installation

24/9/2014 Bradley • 215-1509 Rev. G; ECN 13-08-025

Pre-Installation Information

Barrier-free and ADA compliant - standard height mounting

The Express®Lavatory System with Battery Infrared Control (model MG-3/BIR3) must have a rim height

no higher than 34" above finished floor to be compliant with Americans with Disabilities Act (ADA). When

mounted at 34" rim height, the MG-3/BIR3 Express®meets ADA, ANSI and UFAS requirements for barrier-

free clearances, reaches and controls. Always check local codes and ordinances for compliance.

Barrier-free and ADA compliant - juvenile height mounting

The Express®Lavatory System with Battery Infrared Control (model MG-3/BIR3) must have a rim height no

higher than 30" above finished floor to be compliant with Americans with Disabilities Act (ADA) Accessibility

Guidelines for Buildings and Facilities: Building Elements Designed for Children’s Use; Final Rule.

Texas Accessibility Standards compliant

The Express®Lavatory System with Battery Infrared Control (model MG-3/BIR3) meets Texas Accessibility

standards (TAS) for barrier-free clearances, reaches and controls. Always check local codes and ordinances

for compliance.

Infrared sensor and solenoid

Each sprayhead is controlled by a separate sensor and solenoid valve, enabling each user to activate a single

flow of water. Each valve uses less than half the maximum of hot water allowed by the ANSI/ASHRAE/IES

90A-1980 Standard.

Supplies required for installation

•

(8) ³⁄₈" wall anchors, bolts and washers to mount frame and bowl to wall (minimum pull-out rating of 1,000 lbs.)

• ½"Nominalcoppertubingforhotandcoldsuppliesand1½"NPTdrainpiping

Express®Lavatory System - MG-Series with Battery Infrared Control

Installation MG-3/BIR3

Bradley • 215-1509 Rev. G; ECN 13-08-025 4/9/2014 3

MG-3/BIR3 Express®Lavatory System Dimensions

*Subtract 4" from vertical dimensions for compliance with ADA guidelines for children’s use.

57"

(1445)

77"

(1956)

(mm)

84"

(2134)

72"

(1829)

15"

(381)

15"

(381)

30"

(762)

30"

(762)

(mm)

22"

(559)

*39"

(991)

*33½"

(851)

*29½"

(749)

*17½"

(445)

21½"

(546)

9½"

(241)

(mm)

Express®Lavatory System - MG-Series with Battery Infrared Control

MG-3/BIR3 Installation

44/9/2014 Bradley • 215-1509 Rev. G; ECN 13-08-025

Dimensions continued . . .

TAS Juvenile Height

Grades 6 thru 8 or 9

TAS Juvenile Height

Grades Pre-K thru 5 or 6

37½"

(952mm)

32"

(813mm)

28"

(711mm)

16"

(406mm)

FLOOR

35-1/2"

(902mm)

30"

(762mm)

26"

(660mm)

14"

(356mm)

FLOOR

Express®Lavatory System - MG-Series with Battery Infrared Control

Installation MG-3/BIR3

Bradley • 215-1509 Rev. G; ECN 13-08-025 4/9/2014 5

Installation Instructions

Step 1: Rough in supplies and optional hot water heater

NOTE: See Figure 1 (below), 1a, 1b (for TAS on page 6) and Figure 2 (on page 7) when roughing in the

MG-3/BIR3 Express®.

IMPORTANT: Flush the supply lines before making connections. Debris in supply lines will cause

the valves to malfunction.

IMPORTANT: Dimensions shown in Figure 1 are for Standard Height Mounted MG-3/BIR3 Express®.

1. Roughin½"nominalcoppertubingforhotandcoldsupplylinesthroughwallatdimensionsshown.

2. Roughin1½"NPTdrainwasteconnectionthroughwallatdimensionsshown.

2¾"

(70)

4" (102)

FLOOR

28"

(711)

28"

(711)

*31½"

(800)

*28¼"

(718)*26"

(660)

*19½"

(495)

³⁄₈

" WALL ANCHORS, (8) PLACES

MIN. PULL-OUT STRENGTH 1000 LBS. PER ANCHOR

1½" NPT DRAIN

STUB OUT 2"

*Juvenile Height Mounting:

Subtract 4" from vertical dimensions for compliance with ADA guidelines for children’s use.

Figure 1

Standard Height Mounting

CENTERLINE OF FIXTURE

APPROX. DIMENSION

40½" (1029)

A A

BBB

APPROX. DIMENSION

40½" (1029)

(102)

½" NOMINAL COPPER TUBING FOR HOT

AND COLD SUPPLIES STUB OUT 2"

Express®Lavatory System - MG-Series with Battery Infrared Control

MG-3/BIR3 Installation

64/9/2014 Bradley • 215-1509 Rev. G; ECN 13-08-025

TAS — Texas Accessibility Standards:

Juvenile Height (grades Pre-K thru 5 or 6)

2¾" (70)

4" (102)FLOOR

28"

(711)

28"

(711)

28"

(711)

24¾"

(629)

22½"

(572)

16"

(406)

³⁄₈

" WALL ANCHORS, (8) PLACES MIN. PULL-OUT

STRENGTH 1000 LBS. PER ANCHOR

1½" NPT DRAIN

STUB OUT 2"

Figure 1a

CENTERLINE

OF FIXTURE

APPROX. DIMENSION

40½" (1029)

APPROX. DIMENSION

40½" (1029)

(102)

½" NOMINAL COPPER TUBING FOR HOT AND COLD SUPPLIES STUB OUT 2"

TAS — Texas Accessibility Standards:

Juvenile Height (grades 6 thru 8 or 9)

2¾" (70)

4" (102)FLOOR

28"

(711)

28"

(711)

30"

(762)

26¾"

(679)

24½"

(622)

18"

(457)

³⁄₈

" WALL ANCHORS, (8) PLACES MIN. PULL-OUT

STRENGTH 1000 LBS. PER ANCHOR

1½" NPT DRAIN

STUB OUT 2"

Figure 1b

CENTERLINE

OF FIXTURE

APPROX. DIMENSION

40½" (1029)

APPROX. DIMENSION

40½" (1029)

(102)

½" NOMINAL COPPER TUBING FOR HOT AND COLD SUPPLIES STUB OUT 2"

Express®Lavatory System - MG-Series with Battery Infrared Control

Installation MG-3/BIR3

Bradley • 215-1509 Rev. G; ECN 13-08-025 4/9/2014 7

Installation Instructions continued . . .

Step 2: Rough in wall anchors

1. Install six

³⁄₈

" wall anchors with a minimum pull-out rating of 1,000 lbs. (supplied by installer) at the

locations marked (ref. location “B" shown in Figure 1, 1a or 1b on pages 5-6).

NOTE: The dimensions for the wall anchors at location “A" are for reference only.

2. On the back of the bowl, measure the distance between the ¾" bowl mounting holes. Divide this

measurement in half. Measure and mark this dimension on the wall to the left of the centerline and to the

right of the centerline. Install two

³⁄₈

" wall anchors with a minimum pull-out rating of 1,000 lbs. (supplied by

installer) at the locations marked (ref. location “A" shown in Figure 1, 1a or 1b on pages 5-6).

NOTE: The anchors will be used to mount the Express®MG-3/BIR3 bowl and frame to the wall.

Figure 2

1½" NPT DRAIN

STUB OUT 2"

½" NOMINAL COPPER

TUBING FOR HOT AND

COLD SUPPLIES OR

TEMPERED SUPPLY.

STUB OUT 2"

Express®Lavatory System - MG-Series with Battery Infrared Control

MG-3/BIR3 Installation

84/9/2014 Bradley • 215-1509 Rev. G; ECN 13-08-025

Installation Instructions continued . . .

Step 3: Mount frame to wall

1. Loosen, but do not remove the bottom three access panel screws.

2. Remove the top three access panel screws and washers securing the access panel to the frame and

remove the access panel (see Figure 3).

3. Position the frame with Terreon®End Caps attached, against the wall, ensuring that it is level.

IMPORTANT: Anchoring the frame to a wall that is not flat may cause the frame to bend. If

necessary, install shims to compensate for wall distortion.

4. Ensure that the back of the frame is flat against the wall. If wall is not flat, insert shims behind the frame

to ensure that it will not bend when anchored.

5. Once you have positioned the frame such that it is level and flat against the wall or shimmed, use the

³⁄₈

bolts and washers to mount the frame to the wall.

Figure 3

³⁄₈

" BOLTS AND WASHERS

(6) PLACES

TERREON®

END CAP

LEFT

STAINLESS STEEL

ACCESS PANEL

TERREON®

END CAP

RIGHT

FRAME

¼" - 20 SCREWS

AND FINISHING WASHERS

(6) PLACES

FRONT VIEW

Express®Lavatory System - MG-Series with Battery Infrared Control

Installation MG-3/BIR3

Bradley • 215-1509 Rev. G; ECN 13-08-025 4/9/2014 9

Installation Instructions continued . . .

Step 4: Install bowl assembly

IMPORTANT: See Figure 4 below when installing the bowl assembly. If the fixture has soap option,

refer to the soap system installation manual 215-1585 before installing the bowl

assembly.

1. With someone to assist you, place the bowl assembly squarely onto the frame being careful not to pinch

tubing between bowl and frame.

2. Attachthefrontofthebowlassemblytotheframeusingthefour¼-20x½"pan-head

screws and washers provided. Do not tighten screws at this time.

IMPORTANT: When bolting the bowl assembly to the wall, do not overtighten the bolts.

Overtightening bolts can damage the Terreon®material.

3. After the bowl assembly is attached to the frame, install the two

³⁄₈

" bolts and washers

(supplied by the installer) to bolt the bowl to the wall anchors. Do not overtighten bolts.

4. Tighten the screws installed in procedure #2 above to secure the bowl assembly to the frame.

Do not overtighten.

5. If necessary, adjust sprayhead body to fit closely to wall by adjusting sprayhead mounting bolts. See

Figure 8 on page 13 for sprayhead mounting bolt locations.

Figure 4

³⁄₈

" BOLT

AND WASHER

TERREON®

END CAP (R)

TERREON®

END CAP (L)

FRAME SPRAYHEAD

³⁄₈

" BOLT

AND WASHER

BOWL

¼"-20 x ½"

PAN HEAD

SCREWS AND

WASHERS

(4) PLACES

BACK VIEW

Express®Lavatory System - MG-Series with Battery Infrared Control

MG-3/BIR3 Installation

10 4/9/2014 Bradley • 215-1509 Rev. G; ECN 13-08-025

Installation Instructions continued . . .

Step 5: Connecting supply

1. Loosen but do not remove the two mounting screws holding the valve bracket to the frame. Slide the

valve bracket up until the larger cutout in the frame’s slot aligns with the screw head (see Figure 5b).

Then lift up to remove the valve bracket from the frame.

2. FOR HOT AND COLD SUPPLY: Attach the stops to the hot and cold water supply piping from the wall.

Connect the flexible hoses to the Navigator Mixing Valve and to the stops (see Figure 5a).

NOTE: The “H" on Navigator Mixing Valve indicates hot water supply inlet.

FORSINGLETEMPEREDSUPPLY:Attachthestoptothe½"temperedsupplyline.Connectthestopto

the tempered line adapter with the flexible supply hose (Figure 5c).

3. AssembletheP-trapbyconnectingthe1½"tubularpipetothetailpieceandtothe1½"drainpipestubbed

out of the wall.

4. Install the strainer on the drain plug opening inside the bowl, and push the strainer firmly into place.

Secure the strainer with the screw provided.

Figure 5c

FLEXIBLE

SUPPLY HOSE

(TO SOLENOID

BRACKET)

TO SUPPLY

LINE

TEMPERED

LINE ADAPTER

(S39-804)

Figure 5a

NAVIGATOR

THERMOSTATIC

MIXING VALVE

FLEXIBLE

SUPPLY

HOSE

CONNECT TO

HOT WATER

SUPPLY

CONNECT TO

COLD WATER

SUPPLY

FLEXIBLE

SUPPLY

HOSE

Hot and Cold Supplies

Single Tempered

Supply

Figure 5b

SLOT IN

FRAME

VALVE BRACKET

MOUNTING SCREW

Andere Handbücher für MG Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley S19-120G Bedienungsanleitung

Bradley

Bradley Express MG-2/NDT Bedienungsanleitung

Bradley

Bradley Verge LVQ Series Bedienungsanleitung

Bradley

Bradley S19-310DCFW Bedienungsanleitung

Bradley

Bradley Express MG Series Bedienungsanleitung

Bradley

Bradley TouchTime Bedienungsanleitung

Bradley

Bradley S19-230B Bedienungsanleitung

Bradley

Bradley COMBI5500 Handbuch

Bradley

Bradley Terreon Classic WF2500 Series Bedienungsanleitung

Bradley

Bradley MG-2/TT Bedienungsanleitung

Bradley

Bradley Verge LVQ Series Bedienungsanleitung

Bradley

Bradley S19-220FWPT Bedienungsanleitung

Bradley

Bradley S19-304D1 Bedienungsanleitung

Bradley

Bradley Express Crescent CRS Series Bedienungsanleitung

Bradley

Bradley S19-210SC Bedienungsanleitung

Bradley

Bradley S19-130SSBF Bedienungsanleitung

Bradley

Bradley S59-2005 Bedienungsanleitung

Bradley

Bradley S19-210FW Bedienungsanleitung

Bradley

Bradley Advocate LA Series Bedienungsanleitung

Bradley

Bradley S19-465EFW Bedienungsanleitung

Bradley

Bradley Advocate AV Series Bedienungsanleitung

Bradley

Bradley Express MG Series Bedienungsanleitung

Bradley

Bradley Terreon Deep Bowl WF3200 Series Bedienungsanleitung

Bradley

Bradley Verge LVGD1 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema