Classic Exhibits Visionary DESIGNS VK-1341 Handbuch

Order #XXXXX

Locked layer contains

placeholder marks.

Top View

10’

VK-1341 - 10’ x 10’ Hybrid Inline

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX

Locked layer contains

placeholder marks.

= 1 sq foot

Plan View

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Crate 1 of 1

Order #XXXXX

Locked layer contains

placeholder marks.

CRATE PACKING

Crate Packing

Step 1 of 4

Order #XXXXX

Locked layer contains

placeholder marks.

When assembled

All Velcro faces

back of booth

FRONT VIEW

Assemble frame flat on ground.

88A 10

99A 11

Steps:

1) Connect vertical extrusions [2-2A], [3-3A], [4-4A], [5-5A] together.

See S44 Connection detail.

2) Attach base plates [1] to vertical extrusions, using bolts.

3) Attach horizontals [8] to [8A] and [9] to [9A].

See Z45 Connection detail.

4) Connect horizontals [6,7,8/8A,9/9A,10,11] between

ertical assemblies as shown.

5) Affix graphics to back of backwall assembly, using Velcro.

Item

2,2A

3,3A

4.4A

5,5A

8,8A

9,9A

Qty.

1,1

Description

Base Plate

42” S44 Vertical Extrusion w/ PR37

22” Z45 Horizontal Extrusion

28.875” Z45 Horizontal Extrusion

22” Z45 Horizontal Extrusion

Z45 Connection

PR53

Connector

Z45 Z45

Insert connector into extrusions.

Secure with set screws.

Set Screw

To prevent product loss, keep all

screws attached to connector

after disassembling.

PR53

Connector

S44 Connection

Slide upper extrusion

over connector and

rest on lower extrusion.

Secure with set screws.

To prevent product loss,

keep all screws attached

to connector after

disassembling.

Set Screw

****

Backwall Assembly

Step 2 of 4

Order #XXXXX

Using Your Setup Instructions

The Aero Setup Instructions are created specifically for your configuration. The instructions include an

exploded view of the frame which is sequentially labeled. We encourage you to review the instructions

before attempting to assemble your exhibit.

Connections are kept very simple; no tools required. Everything assembles with push-button connectors.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.

2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood

of shipping damage.

Push-Button

Numbered Label

Connections are made by holding the button down and

sliding the red tube into opposing tube until button locks

into the hole of the opposing tube. To disassemble, push button

and pull or twist extrusions apart.

Locked layer contains

placeholder marks.

Steps:

1) Connect canopy pieces together as shown.

2) Slide fabric cover over assembled canopy

then zip closed.

Button

Push button then rotate

for packing.

Slide canopy mount into groove of

extrusion, then turn canopy mount

clockwise to tighten.

Canopy Mount Attachment

Extrusion

Canopy

Mount

Turn to

Tighten

Place Aero frame over

top of canopy mount.

Canopy

Mount

Aero Frame

Canopy Assembly

Step 3 of 4

Order #XXXXX

Locked layer contains

placeholder marks.

Shelf

Canopy

Header

Shelf

Slide light onto clip then lock clip

into groove of horizontal extrusion.

Clip

Light

Light Attachment

Clip

Light

Horizontal Extrusion

Shelf Attachment

Insert lock into groove of vertical

extrusion, then tighten set screw.

Lock

Set Screw

Back of Shelf

Canopy

Mount Canopy

Mount

Counter Top

Monitor

Mount

Item

Qty.

Description

38.414” S40 Angled Extrusion Tighten set screw to

secure A10 to extrusion.

A10 Clamp

Tighten knob to secure

wing panels.

***

Steps:

1) Attach clamps to [7] [9/9A] and [11]. See A10 Clamp detail.

Clamp header to top of assembed backwall.

2) Attach lights, where desired, to top of assembled backwall.

See Light Attachment detail.

3) Attach canopy mounts to [7] and [11]. See previous page

for Canopy Mount Attachment detail. Place assembled

canopy onto canopy mounts, with zipper facing to back.

4) Attach counter top between extrusions [3] and [12].

5) Attach shelves to [4] and [5]. See Shelf Attachment detail.

6) Attach monitor mount to [3A]. See Monitor Mount Attachment detail.

Completed Assembly

Monitor Mount Attachment

Connectors

Slide V4 Connectors into groove

of Extrusion. Tighten Set Screws

to secure connectors in place.

Attach Monitor Mount back

piece to Extrusion, using bolts.

Then slide monitor mount into

back piece.

Bolts

Monitor

Mount

Back

Piece *

Backwall Attachments

Step 4 of 4

Order #XXXXX

Locked layer contains

placeholder marks.

Door

Completed Pedestal Assembly

Infill

Keep extrusions [1/4/6/6A] assembled.

6A Keep extrusions [2/3/6/6A] assembled.

Pedestal Top

Shelf

Support

Align hole with pin Rotate pin. Spring

will push pin into hole.

Pedestal Top Attachment

Steps

1) Attach horizontal extrusions [5] and [7] between assemblies [1,4,6,6A] and [2,3,6,6A],

making sure Velcro is facing inward.

2) Connect vertical extrusions [3A] and [4A] on top of horizontal extrusion [7].

3) Slide infill between verticals [3A] and [4A].

4) Attach assembled door to vertical extrusion [1]. See Door Connection detail.

5) Attach upper horizontal extrusions [5] and [7] between assemblies and on top of infill and door.

6) Connect shelf supports to Velcro, then set shelf on top of supports.

7) Attach pedestal top to extrusions [6A]. See Pedestal Top Attachment detail.

Door

Hinge

Slide pin into

hinge attached

to vertical.

Slide door

hinge over pin.

Door Attachment

Item

6,6A

Qty.

2,2

Description

38“ GS220 Vertical Extrusion w/ Door Hinges

38” GS220 Vertical Extrusion w/ Door Stop

38“ GS210 Vertical Extrusion

34.417” Z33 Vertical Extrusion

38” GS210 Vertical Extrusion

34.417” Z33 Vertical Extrusion

22.0197“ Z45 Horizontal Extrusion

12.5” Z45 Horizontal Extrusion

25.639“ Z45 Curved Extrusion

MOD-1267 Pedestal Assembly

Inhaltsverzeichnis

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits visionary designs VK-2084 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS 38907 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-2009 Handbuch

Classic Exhibits

Classic Exhibits Visionary Designs MOD-1243 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-2959 Handbuch

Classic Exhibits

Classic Exhibits RE-2015 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1950 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYMPHONY SYK-2003 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1016 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1019 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS LTK-1152 Handbuch

Classic Exhibits

Classic Exhibits visionary designs MOD-1529 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1340 Handbuch

Classic Exhibits

Classic Exhibits SEGUE DESIGNS MOD-1624 Handbuch

Classic Exhibits

Classic Exhibits Curved Counter Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1137 Bedienungsanleitung

Classic Exhibits

Classic Exhibits euro lt HYBRIDS Mod-1122 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-2005 Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1218 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYMPHONY SYK-1032 Handbuch

Classic Exhibits

Classic Exhibits gravitee GOD-1557 Handbuch

Classic Exhibits

Classic Exhibits gravitee GK-1014 Bedienungsanleitung

Classic Exhibits

Classic Exhibits LTK-1139 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1181 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung

Classic Exhibits visionary DESIGNS VK-1341 Handbuch

Beliebte Inneneinrichtung Handbücher anderer Marken