CrimeStopper CS-2002 Bedienungsanleitung

CS-2002DC

REMOTE CONTROL ALARM SYSTEM

INSTALLATION & OPERATING INSTRUCTIONS

INTRODUCTION

CONGRATULATIONS on your choice of a Gargoyle™ Remote Alarm System by Crimestopper Security

Products Inc. This system features DYNAMIC CODE anti code-grabbing technology. The remote control

code changes with every use of the transmitter making it impossible to scan or record the codes for use later

on. This booklet contains the information necessary for installing, using, and maintaining your alarm system.

If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech

Support number below.

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Siren,

L.E.D., Power, Ground, Doorpin, etc.

-OPTIONAL: These are features to be connected only if desired or agreed upon by the installing dealer (i.e.

Door Locks, Flashing Lights, Starter Kill, Hood, Trunk, and Auxiliary Remote Outputs etc.)

TECH SUPPORT

Mon-Fri 8:00 AM-4:30 PM Pacific Time

(800) 998-6880

This device complie

s with FCC Rules part 15. Operation is subject to the following

two conditions: 1) This device may not cause interference, and (2) this device

must accept any interference that may be received, including interference that may

cause undesired operation. The manufacturer is not responsible for any radio or

TV interference caused by unauthorized modification to this equipment. Such

modification could void the user's authority to operate the equipment.

INSTALLATION CAUTIONS & WARNINGS

BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR

BAGS, ABS BRAKES, AND BATTERY).

TO PREVENT A POSSIBLE DEAD BATTERY remove vehicle dome light fuse while working on the vehicle.

MAKE CERTAIN TO REINSTALL FUSE PRIOR TO TESTING FOR DOOR TRIGGERS.

DO NOT EXCEED MAXIMUM OUTPUT RATINGS! -SERIOUS DAMAGE MAY OCCUR. LIMITS FOR

ALARM FUNCTIONS ARE LISTED WHERE APPLICABLE. IF UNSURE ABOUT CURRENT LOAD,

MEASURE LOAD WITH AN AMP-METER.

REMOVE MAIN SYSTEM FUSE(S) before jump starting the vehicle or charging the battery at high boost.

DAMAGE MAY OCCUR TO SYSTEM IF PROPER PRECAUTIONS ARE NOT OBSERVED.

DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering

column, or any other moving parts in the vehicle.

CONTROL MODULE MOUNTING

DO NOT Mount the control unit in the engine compartment.

DO NOT Mount the control unit or wiring harness where they can become entangled with moving parts

such as brake/gas/clutch pedals, or the steering column.

The alarm control module should be mounted in a concealed location. The Placement of the module will

affect the distance from which the remote transmitter can control the unit. The antenna wire should be routed

away from any metal if possible. Do not alter the length of the antenna wire or route it with other wires. Do

not ground the antenna wire.

Underdash Mounting: If you are locating the control unit underdash, mount it as high as possible not easily

located by an intruder.

Driver’s Side underdash mounting provides an easy location for wiring however this is a common location for

an intruder to check for an alarm after breaking into the vehicle. The left side of the vehicle may contain more

metal and or wiring that will create interference and decrease the operating range of the system.

Passenger Side underdash is often the best location, however some extra wiring may be needed to extend

wires across from the driver’s side.

Under-seat / Center Console mounting is also a possibility however range be affected by metal structures

and of the unit may be exposed to moisture from spilled drinks etc. Moisture or Damage caused by corrosion

is not covered under warranty.

COMPONENT MOUNTING

SIREN MOUNTING: Mount the siren under the hood to fender-well or other body surface with the open end facing

downward. Run the red siren wire through the firewall using a rubber grommet. Ground the black wire to the body

metal near the siren.

LED: Mount the red LED in a visible location on the dashboard or console.

Shock Sensor: Mount the included shock sensor with wire ties to an under dash wire harness or fasten with screws to

firewall or side paneling.

Override/Program Button: Mount the Override/Program push-button in a hidden but accessible location. It is used

for emergency disarm without the use of the transmitter and for programming certain features.

WIRING

RED WIRE: +12V POWER INPUT (15 amp fuse)

Connect to +12 Volt source with supplied fuse & holder. Recommended location for this connection is at the vehicle

battery positive terminal.

BLACK WIRE: SYSTEM CHASSIS GROUND

THIS WIRE MUST BE CONNECTED TO CHASSIS METAL OF THE VEHICLE. Scrape away any paint or dirt from

the connection point to ensure a good connection. We recommend the kick panel area for your ground point.

YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS

Connect to an ignition wire (or fuse in the fuse box) that shows +12 Volts when the key in both “On” and “Start”

positions.

ORANGE WIRE: STARTER KILL / NEGATIVE ARMED OUTPUT (500mA Ground)

Ground output when system is armed. This output is used for disabling the starter or to activate other devices such as

scanner LED’s, window modules, voice modules etc. For starter kill, cut starter wire and connect between 87A and 30

on relay. Connect orange wire to 85 and connect 86 to an Ignition source that has voltage in the ON and CRANKING

position.

WHITE WIRE: +12V FLASHING PARKING LIGHT OUTPUT (Optional)

Connect to switched parking light wire at back of light switch. If this is not possible, connect directly to one of the

parking lights at the front of the vehicle. European vehicles require separate right and left circuits. Use a dual relay or

2 diodes to separate the output signal.

BROWN WIRE: (+) SIREN OUTPUT (3 Amp Max.)

Connect to RED siren wire.

WIRING

BLUE WIRE: (-) HOOD/TRUNK TRIGGER

Input trigger for a grounding hood or trunk pin switch. Connect to existing hood and trunk pin switches that read

ground when open. If no existing switches are available, install new pin switches if desired. Note: DO NOT mount

new pin switches in water pathways.

GREEN WIRE: (-) DOOR TRIGGER

Identify the wire that reads ground when any door is open and 12 volts when all doors are closed. Some vehicles may

have isolated door triggers. In this case you may need to run additional wires from other doors or go directly to the

wire that triggers the vehicle’s dome light.

VIOLET WIRE: (+) DOOR TRIGGER

Same as GREEN wire above except this wire is used for vehicles that show a positive voltage (12 volts) when the door

is open such as Ford.

GRAY WIRE: (-) AUX REMOTE OUTPUT 1 (Optional, requires relay)

Connect to terminal 85 of relay. Connect terminal 86 to constant. Connect terminal 87 to +12V or Ground depending

on the type of circuit that needs to activated. Connect terminal 30 to the device/circuit to be activated.

WHITE/RED WIRE: (-) AUX REMOTE OUTPUT 2 (Optional, requires relay)

This wire connects the same way as Remote Output 1 see GRAY WIRE above.

BLACK/WHITE WIRE: (-) DOME LIGHT ILLUMINATION OUTPUT (Optional, requires relay)

Connects to terminal 85 of a relay. Connect terminal 86 to +12V Constant. Connect terminal 87 to +12V or Ground

depending on the type of dome light circuit in the vehicle. Connect terminal 30 to the dome light circuit.

BROWN/WHITE WIRE: (-) HORN HONK/CHIRP OUTPUT (Optional, requires relay)

Connects to terminal 85 of a relay. Connect terminal 86 to +12V Constant. Connect terminal 87 to +12V or ground

depending on the type of horn activation circuit in the vehicle. Connect terminal 30 to the horn activation circuit.

BLUE/WHITE WIRE: (-) PASSENGER(S) DOOR UNLOCK OUTPUT (Optional, requires relay)

Connects to unlock circuit for passenger door(s) when using separate driver’s door unlock option. See DOOR LOCK

WIRING for configuration options.

2 PIN PLUG (BLUE): PROGRAM/OVERRIDE PUSH BUTTON

2 PIN PLUG (RED): LED INDICATOR (RED FLASHING LIGHT)

4 PIN SENSOR PLUG:

WHITE WIRE: NEG. WARN AWAY *The Sensor supplied with the system does not require

BLUE WIRE: NEG. TRIGGER any additional wiring, simply mount the sensor in a

BLACK WIRE SENSOR GROUND suitable location, plug in, and adjust sensitivity.

RED WIRE SENSOR +12V POWER

POWER DOOR LOCK WIRING

3 PIN DOOR LOCK PLUG (Optional):

GREEN: (-) Negative pulse for LOCK

RED: +12V Coil Power for external relays TERM 86.

BLUE: (-) Negative pulse for UNLOCK

DETERMINING DOOR LOCK TYPE: We recommend determining the type of locking system the vehicle has

before connecting any wires. Incorrect connection will result in damage to the remote start and/or vehicle

locking system. There are several types of door lock systems in vehicles today. Below is listed the many

types of common locking systems:

Negative trigger: Most Japanese; Ford, New GM Positive trigger: Many GM; Some Chrysler

One wire dual voltage: Newer /Chrys/Dodg/Plym; Ford Probe

Reverse Polarity: Chrys/Dodg/Plym; GM; Ford Ground/open: Some Nissan; Subaru

Semi-automatic: Older Saab and Volvo Electric vacuum pump: Pre-‘95 Mercedes-Benz

NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING

GREEN

GREEN FUSED

RED +12VRED BLUE +

BLUE

858685 8787 3087A30

87A

FACTORY

LLPOWER

POWER LOCKING

LOCKING

UL UL

RELAYS RELAYS

POWER DOOR LOCK WIRING

SEPARATE DRIVER’S DOOR UNLOCK WIRING

NEGATIVE TRIGGER DOOR LOCKS

BLUE/WHITE

GREEN

RED

BLUE

DRIVER'S

DOOR MOTOR

8685 LL

87 ULUL

87A

FACTORY LOCK

RELAYS

+12V

+FUSED

UNLOCK WIRE CUT

AFTERMARKET MOTOR/DOOR LOCK WIRINGREVERSE POLARITY DOOR LOCK WIRING

GREEN

GREEN FUSED

FUSED RED

RED +12V

+12V BLUE

BLUE +

86858685

86858685 8787

8787 3087A3087A

3087A3087A

CUT

MASTER

SWITCH

LOCK

UNLOCK

SEPARATE DRIVER’S DOOR UNLOCK WIRING

WIRING FOR REVERSE POLARITY DOOR LOCKS

BLUE/WHITE

GREEN FUSED

RED +12V

BLUE +

DRIVER'S

86858685

DOOR

8685 8787

87 30

87A

30 87A

CUT

UL UL

CUT

UNLOCK WIRE

WIRING FOR POSITIVE TRIGGER DOOR LOCKS

BLUE/WHITE

GREEN 8685

RED

BLUE 87 30

DRIVER'S

DOOR

8685 L

87 UL

87A

FACTORY LOCK

RELAYS

+12V

+FUSED

UNLOCK WIRE CUT

8785

86 30

TRANSMITTER PROGRAMMING

1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3rd time. (ON/OFF, ON/OFF, ON) You should hear (3)

chirps.

2. Push and release the Program/Override Button 5 times and the Status LED will come on solid.

3. Press #1 (LOCK) on new transmitter two times. LED goes out, siren chirps one time, and LED will flicker for

confirmation.

4. Turn off Ignition.

Note1: Repeat steps 1 through 4 to teach the unit up to 3 transmitter codes Max.

Note 2: You can program button 4 (PANIC) from another vehicle’s CS-2002DC alarm to Arm/Disarm THIS alarm

system by pressing the other vehicles Button#4 two times in step 3. The Other transmitter will only toggle

ARM/DISARM with button 4 and not perform any auxiliary features on THIS system.

DIAGRAM:

IGN

OFF

STATUS LED

ON SOLID

PANIC

TURN IGN. ON

3 TIMES:

ON, OFF

ON.

3 CHIRPS

PRESS

BUTTON

5 TIMES

PRESS BUTTON

#1 TWO TIMES

LED GOES

1 CHIRP

OUT

LED FLICKER

OPTION PROGRAMMING

CS-2002DC PROGRAMMABLE OPTIONS

1. Turn the Ignition ON and press the Override/Program button 5 times. You should hear 6 confirmation chirps.

2. Within the next few seconds, press the Override/Program button [again] the number of times that corresponds to

the feature list below. The siren will chirp for each button press. DO NOT LOSE COUNT!!

3. When you get to the desired option number, press buttons#1,#2, or #3 (Lock, Unlock, Trunk) on the transmitter to

change the option.Button 1 gives a single light flash,Button 2gives two light flashes, and Button 3 gives three light

flashes. See chart Below for Option descriptions and vales.

4. Change ONE option at a time repeating steps 1-3 as needed. When you are finished customizing options, check

operation to see if the option(s) have changed.

PROGRAMMING OPTIONS CHART

Option #

Option Description BUTTON 1

LOCK

(Default)

BUTTON 2

UNLOCK BUTTON 3

TRUNK

1. Passive Arming ON OFF

2. QuietChirp Arm/Disarm

with Button #3 ON OFF

3. Lights on with disarm ON OFF

4. Active Re-Arm ON OFF

5. Silent Arm/Disarm OFF ON

6. Disarm with trunk pop OFF ON

7. Ignition controlled Locks ON OFF

8. Door Lock Pulse Time 0.7 Sec. 3 Sec.

9. Carjack Enable/Disable DISABLE ENABLE

10. Lock with passive arm ON OFF

11. Double Unlock Pulse OFF ON

12. Type of Carjack Protection

ACTIVE PASSIVE FULL-TIME

13. 10/60 Sec. Door Open

Warning 10 Sec. 60 Sec.

14. Horn Chirps OFF Arm/Disarm

Only Arm/Disarm/

Pre-Warning

1. PASSIVE ARMING

This option controls the Passive (Automatic) Arming feature. If ON, arming will occur 30 Seconds after the ignition is

turned off and the last door has been closed. The LED will begin flashing rapidly while counting down. If a door is

reopened, the system will wait (LED solid) for the door or zone to close before arming. The unit will chirp once and

flash the lights once. Doors will lock if passive locking is selected. Factory default setting is ON.

OPTION PROGRAMMING

2. SOFT CHIRP ARM / DISARM WITH BUTTON #3 (SHORT PRESS)

With this feature, the system can be programmed to Arm and Disarm with a very soft siren chirp using a short press on

button #3 on the remote. The Factory Default setting is ON.

3. PARKING LIGHTS ON WITH DISARM

Keeps parking lights on instead of 2 flashes when system is disarmed to assist in locating your vehicle in a crowded

parking lot or structure. Light will stay on for 30 Sec. or until Ignition is turned on. Factory Default setting is ON.

4. ACTIVE RE-ARMING

Active Re-arming allows the system to re-arm itself 30 seconds after disarmed with the transmitter if a door has not

been opened. This is handy if the vehicle is accidentally disarmed (via the Transmitter in your pocket) without you

knowing it. The Factory default setting is ON.

5. SILENT ARMING /DISARMING (NO CHIRPS)

With this feature, the system can be programmed to Arm and Disarm without the siren chirp. Flashing parking lights

will be the only Arm/Disarm confirmation. The Factory Default setting is OFF.

6. DISARM WITH AUX. OUTPUT 1

Controls whether the system will or will not DISARM when the trunk pop or AUX. feature is used. When the feature is

turned on the unit will DISARM when opening trunk or other AUX feature. Factory Default setting is OFF

7. AUTOLOCK/UNLOCK

Controls whether the doors will automatically lock when the ignition is turned on and will unlock when the ignition is

turned off. Doors will not lock if they are open to prevent locking the keys in. Factory default setting is ON

8. DOOR LOCK/UNLOCK PULSE TIME

Controls the amount of time (0.75 sec. or 3 sec.) for the lock/unlock pulse. The 3 sec. setting may be required for

1980’/90’s European Vehicles that require a long pulse to do Vacuum door lock systems. Factory default is 0.75 sec.

9. CARJACK FEATURES

Enable or Disable Carjack protection features. Factory Default is OFF.

10. PASSIVE LOCKS

This option controls whether the doors will lock when Passive Arming occurs. Note: May increase the risk of locking

keys in the vehicle. Factory default setting is ON.

11. DOUBLE UNLOCK PULSE

The unit will send 2 unlock pulses when the #2 Unlock button is pressed. This feature may be required for interfacing

this alarm with an existing Factory Keyless Entry or Alarm system in a vehicle. These systems are found on some

Nissan, VW, Toyota, and Lexus vehicles. Factory Default setting is OFF.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CrimeStopper Autoalarmanlage Handbücher

CrimeStopper

CrimeStopper CS-2013FM Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9228MX Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8716 Handbuch

CrimeStopper

CrimeStopper Fortress FS-30 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9602PI Betriebsanleitung

CrimeStopper

CrimeStopper CS-9200 Samurai Bedienungsanleitung

CrimeStopper

CrimeStopper Gargoyle CS-2001FC II Series Handbuch

CrimeStopper

CrimeStopper CS-9711 Systemhandbuch

CrimeStopper

CrimeStopper Traknet TN-4011 Bedienungsanleitung

CrimeStopper

CrimeStopper HP-8710 Kurzanleitung

CrimeStopper

CrimeStopper CS-882 OEM Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Bedienungsanleitung

CrimeStopper

CrimeStopper CG-1100 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-883 OEM Bedienungsanleitung

CrimeStopper

CrimeStopper Fortress FS-40 Systemhandbuch

CrimeStopper

CrimeStopper CS-2014.DPII.FM.TW2 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9002 Service-Handbuch

CrimeStopper

CrimeStopper Super Rage CS-2011DP Systemhandbuch

CrimeStopper

CrimeStopper RS-300 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2011RS.II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9709 Kurzanleitung

CrimeStopper

CrimeStopper CS-2003DC II Series Handbuch

CrimeStopper

CrimeStopper SP-100 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2015.FM.RevB Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung