Endress+Hauser Analytikjena Biometra ThermoShaker TSC Anleitung zur Verwendung

Short Manual Biometra ThermoShaker TSC

Analytik Jena GmbH

Konrad-Zuse-Strasse 1

07745 Jena ⋅ Germany

Phone +49 3641 77 70

[email protected]

www.analytik-jena.com

Short Manual Biometra ThermoShaker TSC

Version: A (08/2022)

34-9990-063-23

1/2

CAUTION

Risk of damage to health

The device is used to heat biological and biochemical hazardous substances to temperatures

of up to 100°C. Improper operation of the device and incorrect handling of samples may

result in injury.

¡Only use the quick reference guide together with the detailed operating manual.

¡Risk of burns from the hot block module and the samples!

¡Mix and temper samples only in sealed and heat-resistant tubes and microplates.

¡Wear personal protective equipment If samples open during operation, hot liquids may

spurt out.

Design

The thermoshaker consists of:

¡Basic device with control panel

¡Interchangeable block modules for the samples

(must be ordered separately)

The control panel has arrow keys for setting the timer, mixing frequency and temperature.

The set and actual values are shown on the display.

Timer 1minto96h, with signal tone (buzzer)

Mixing frequency 250to1400rpm

Temperature control

range

+4to+100°C

Heating rate 5°C/min (+25to+100°C)

Cooling rate 5°C/min (+100to+25°C)

1.8°C/min (+25to+4°C)

Installation/changing a block

}Switch off the basic device safely and allow it to acclimatize.

}Select a suitable block module.

NOTICE!Switch off the device before installation/changing a block.

}Align the block module so that the labeling faces to the front.

}Connect the block module to the basic device using the 10-pin connector.

}Place the block module straight onto the basic device and fasten it with the four screws.

}Connect the device to the power outlet using the power supply unit. Switch on the device

using the ON/OFF switch at the rear of the device.

üThe device is ready for operation and immediately starts to temper the block module.

Operation

Starting the program:

}On the control panel, set the desired values for

time, mixing frequency and temperature.

}When T(°C) Actual = T(°C) Set: Place the prefilled

and sealed samples in the block module.

CAUTION!The block module can become

very hot.

}Start the program with Start/Stop Shaker.

End of program: An acoustic signal (buzzer) sounds.

}End the program with Start/Stop Shaker.

}End temperature control by entering T<4°C.

Or: Insert the next samples into the device and start a new program run.

Short Manual Biometra ThermoShaker TSC

Analytik Jena GmbH

Konrad-Zuse-Strasse 1

07745 Jena ⋅ Germany

Phone +49 3641 77 70

[email protected]

www.analytik-jena.com

Short Manual Biometra ThermoShaker TSC

Version: A (08/2022)

34-9990-063-23

2/2

Interrupting the program:

¡Use Start/Stop Timer to reset the timer to 00:00. Tap the key a second time and start

the timer again.

¡Or: Interrupt the mixing process with Start/Stop Shaker. STOP is shown on the display.

Tap the key a second time to restart the mixing process and the timer.

Operate the device using the arrow keys and the start/stop keys:

Keys Input

Time Input duration in h:min

If 00:00 is entered: continuous operation

RPM Input mixing frequency in rpm

If 000 is entered: only temperature control active

T(°C) Input block temperature in °C

If T<4°C is entered: Display: OFF, only mixer active

Start/Stop Shaker Start and stop program

Temperature control stops only after entering T<4°C.

Start/Stop Timer Reset: Set the timer to 00:00

Calibration

Calibration compensates for the different thermal conductivities of sample tubes/microplates

from different suppliers. Calibration coefficient: 0.936to1.063 (±0.063)

}Insert an empty sample tube or an empty microplate into the block module.

}Insert an external temperature sensor (±0.5°C) into the tube/well.

}Set a temperature of, e.g., 40°C, on the device.

}After 30min, compare T(°C) Actual with the sensor temperature. Calibrate the device if

there is a deviation.

Set

Actual

Time (h:min) RPM T(°C)

sct. 40.0 40.0

39.0 40.00.975

2 3

}Press the Start/Stop Timer key for longer than 8s. The calibration mode is active when

sct. (1) appears on the display.

}Adjust the temperature (3) with the arrow keys until the sensor temperature is reached

(here: 39°C). The calibration coefficient (2) adjusts itself automatically.

}Save the calibration coefficient with the Start/Stop Shaker start/stop key and exit the

calibration mode.

Maintenance

Cleaning the device:

}Switch off the device before carrying out external cleaning. Disconnect the device from

the electrical mains supply.

}Clean the housing using a slightly damp, not dripping cloth with water and commercially

available surfactants. Disinfect with ethanol (75%).

Replace the rubber belt after 1.5years or 2,000operating hours:

The rubber belt transmits the power from the shaker motor to the block module and thereby

generates the mixing movement.

}Switch off the device.

}Disconnect the plug of the external power supply.

}Carefully place the device on its side.

}Remove the base plate. To do so, loosen the four

Phillips screws.

}Change the rubber belt.

}Reassemble the base plate.

Andere Endress+Hauser Laborausrüstung Handbücher

Endress+Hauser

Endress+Hauser Levelflex M FMP41C Montageanleitung

Endress+Hauser

Endress+Hauser Liquistation CSF39 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Analytik Jena UVP DigiDoc-It Leitfaden

Endress+Hauser

Endress+Hauser Liquiport 2010 CSP44 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Analytik Jena InnuPure C16 touch Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiport 2010 CSP44 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquistation CSF48 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Analytik Jena TOPwave Bedienungsanleitung

Endress+Hauser

Endress+Hauser analytikjena multi N/C 2100 Bedienungsanleitung

Endress+Hauser

Endress+Hauser analytikjena ZEEnit 700 Q Bedienungsanleitung

Endress+Hauser

Endress+Hauser asp-port d 2 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Analytik Jena APU 28 Series Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiport 2010 CSP44 Technische Daten

Endress+Hauser

Endress+Hauser Liquiphant FTL62 Density Bedienungsanleitung

Endress+Hauser

Endress+Hauser analytikjena qTOWER3 84 auto Bedienungsanleitung

Endress+Hauser

Endress+Hauser analytikjena Biometra TRIO Anleitung zur Verwendung

Endress+Hauser

Endress+Hauser Analytik Jena CyBio SELMA Bedienungsanleitung

Endress+Hauser

Endress+Hauser Analytik Jena Biometra TRIO Bedienungsanleitung

Endress+Hauser

Endress+Hauser analytikjena CyBio SELMA Series Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquistation CSF34 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquistation CSF33 Technische Daten

Endress+Hauser

Endress+Hauser Analytik Jena PlasmaQuant PQ 9000 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Analytik Jena Biometra TOne Anleitung zur Verwendung

Endress+Hauser

Endress+Hauser KIO1 Technische Daten

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung

Yamato

Yamato BM510 Bedienungsanleitung

Endress+Hauser analytikjena Biometra ThermoShaker TSC Anleitung zur Verwendung

Beliebte Laborausrüstung Handbücher anderer Marken