EPOX BXB Bedienungsanleitung

TRADEMARK

All products and company names are trademarks or registered

trademarks of their respective holders.

These specifications are subjected to change without notice.

Manual Revision 1.1

July 15, 1999

BXB (SMP)

A Dual Pentium®II Processor based

AGP motherboard (100/66MHz) with

Adaptec Ultra-2 SCSI onboard.

FeaturesBXB

Page 2

FEATURES

BXB Features:

•BXB is based on the Dual Pentium®II Processor operating at 233 ~ 333

MHz (66MHz) or 300-450 MHz (100MHz) on Slot 1. The board is configured

by an Easy-Setting-Single-Jumper (E.S.S.J.) to match your CPU clock speed.

•Designed with Intel’s 82443 BX AGPset.

•Supports up to 1 Gigabyte of SDRAM (minimum of 8 MB) on board, You can

use 168-pin DIMM x 4. It will automatically detect Extended Data Output

(EDO) DRAM or Synchronous DRAM memory (SDRAM)

•BXB will support Error Checking and Correcting (ECC) when using

parity DRAM memory modules. This will detect multiple bit errors and correct

1-bit memory errors.

•Supports (2) 16 bit ISA slots, (4) 32 bit PCI slots, (1) AGP slot and provides

(2) independent high performance PCI IDE interfaces capable of supporting

PIO Mode 3/4 and Ultra DMA 33 devices. The BXB supports (4) PCI

Bus Master slots and a jumperless PCI INT# control scheme which reduces

configuration confusion when plugging in PCI card(s).

•Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary IDE

interfaces.

•Designed with Adaptec AIC-7890 Ultra-2 Wide SCSI for LVD (80 Mbytes/

sec) devices and Adaptec AIC-3860 for legacy single-ended SCSI devices.

(please see Section 3-6).

•Designed with Winbond W83977 Multi I/O: (1) floppy port, (1) parallel port

(EPP, ECP), and (2) serial ports (16550 Fast UART), (1) IrDA.

Note: Japanese “Floppy 3 mode” is also supported

•Includes a PS/2 mouse connector.

•Allows use of a PS/2 or AT keyboard (with optional adapter).

Features BXB

Page 3

•Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.2themax.com/

please visit our Technical Support section for the latest updates)

•BXB utilizes a Lithium battery which provides environmental protection

and longer battery life.

•Supports the Universal Serial Bus (USB) connector. The onboard PIIX4 chip

provides the means for connecting PC peripherals such as keyboards,

joysticks, telephones, and modems.

•Built-in ATX 20-pin power supply connector.

•Software power-down when using Windows®95/98.

•Supports ring-in feature (remote power-on through external modem,

allows system to be turned on remotely).

•Power on by Alarm - Allows your system to turn on at a preselected time.

•Power Loss Recovery - In the event of a power outage your system will

automatically turn itself back on without user intervention.

•Supports CPU Hardware sleep and SMM (System Management Mode).

•Supports Desktop Management Interface (DMI) facilitating the management

of desktop computers, hardware and software components and peripherals,

whether they are stand-alone systems or linked into networks. (option)

• Supports Hot Key, Any Key, or password Keyboard power ON function

(KBPO).

• Supports USDM software which allows Windows®95/98, or Windows®NT 4.

0 to monitor various aspects of the system hardware.

• Supports stopping the CPU, AUX, and Chassis FANs during sleep mode.

• Supports blinking of the System Power LED (PANEL) during sleep mode.

• Built-in WOL (Wake On Lan) Connector.

• Built-in SB-LINK Header for Creative Labs Sound Blaster® AWE64D PCI

sound card.

Installation BXB

Page 4

Intel

443BX

PCIset

JP1

Clear

CMOS

Secondary IDE

Primary IDE

IDE1

IDE2

FDD Connector

FDD1

PCI Slot #1

AGP SLOT

CPU Cartridge SLOT 1

PCI Slot #2

PCI Slot #3

PCI Slot #4

ISA Slot #1

ISA Slot #2

COM 1COM 2

USB 1

(Top)

Mouse

(Top)

USB 0

(Bottom)

PS/2 Keyboard

(Bottom)

USB

Parallel Port

Primary

Secondary

ATX Power Input

PW1

DIMM 2

DIMM 1

Flash Memory

for BIOS

Bank 0

Bank 1

DIMM 3

DIMM 4

200

Bank 2

Bank 3

Intel

PIIX4

PCIset

Intel

82093A

CPU 1

Fan

Chassis

Fan

CPU 2

Fan

Adaptec

AIC-3860

J7 Wake On-Lan

Wide SCSI (legacy)

Narrow SCSI (legacy) SCJ2

SCJ1

Ultra-2 SCSI (LVD)

SCJ3

233

266

300

333

366

MHz

300

350

400

450

500

550

MHz

Adaptec

AIC

7890

Winbond

83977

I/Oset

SB-Link

KBPO

JP13

JP100

SCSI RAID (option)

PWR/ON

RST

TBLED

H/D LED

SPEAK

KEYLOCK

/PWRLED

Figure 1

BXB Detailed Layout

InstallationBXB

Page 5

Easy Installation Procedure

The following must be completed before powering on your new system:

Configure Jumpers to match your hardware

Install memory chips

Device Connectors

Adaptec SCSI setup

Configure Jumpers

2theMax designs all motherboards with the fewest jumpers to make your setup fast and

easy.

The following will describe all of the jumpers that are required to be set before

moving on to step 2.

Note: The jumpers as shown in Figure 1 are in their correct physical

orientation.CMOS Clear

JP1: = 1-2 - Run Mode (Default)

= 2-3 - Clear CMOS

JP1:1

JP13:

Keyboard Power-ON function (see page 3-12)

JP13: = 1-2 - Enable

= 2-3-Disable(Default)

J1:

J7:

SB-LINK Header:

Reserved for Creative Labs AWE64D PCI sound card

whichallowsforDOSmodecompatibility.

WOL(Wake OnLan):

Reserved for NIC (Network Interface Card) which when

usedwithcompatiblesoftwarewillallowthe systemtobe

poweredonremotelyusinganetworkconnection.

Installation BXB

Page 6

ESSJ

JP3:

NOTE: Based on the implementation of the Intel 440BX AGPset the BXB is

able to provide two front side bus (FSB) frequencies -- either 66MHz or 100MHz

for Slot 1 processors and memory operations. The motherboard will automatically

detect the correct FSB and set accordingly unless JP100 is set otherwise (see

jumper JP100 below). The primary and secondary processor slots both operate

synchronously at either 66MHz or 100MHz FSB, therefore if two processors are

used both will need to be of the same type and speed; otherwise the lower of the

two FSB frequencies will be set. When using the 100MHz FSB you must use

PC100 compliant SDRAM.

Memory is an important component of any 100MHz motherboard. When selecting

memory for use on your 2theMax brand motherboard we recommend using only the

finest quality modules. 2theMax would like to stress that using non-compliant PC100

SDRAM modules with a 100MHz FSB severely compromises the integrity of the

system.

Single or Dual Processor Selection

CPU Clock Rate

66MHz FSB CPU Clock Rate

100MHz FSB

1300MHz

350MHz

400MHz

450MHz

550MHz(RSD)

200MHz

233MHz

266MHz

300MHz

333MHz

(RSD) 366MHz

* Default at 266MHz (66MHz FSB)

* RSD (Reserved for future use)

JP100:1(FSB) Bus Clock Selection

JP100: = 1-2 - AUTO (Default)

= 2-3 - PC100 Only (100MHz FSB)

500MHz(RSD)

InstallationBXB

Page 7

System Memory Configuration

Memory Layout

The BXB supports (4) 168-pin DIMMs (Dual In-line Memory Module). The

DIMMs can be either EDO (Enhanced Data Out) or SDRAM (Synchronized

DRAM). Do not mix EDO DIMM and SDRAM DIMM in the system.

•SDRAM DIMM may be 100 MHz (10ns) or 125 MHz (8ns) bus speed.

• SDRAM DIMM may be 8MB, 16MB, 32MB, 64MB, 128MB, or 256MB

registered (see table 2).

•100MHz FSB frequency requires PC100 compliant SDRAM memory.

•4 clock SDRAM is recommended instead of 2 clock.

•If using 50ns and 60ns EDO DIMM together you must set BIOS for 60ns.

•Table 1 shows several possible memory configurations.

•Table 2 shows compatible SDRAM components types according to Intel

440BX datasheets. (Internet: http://developer.intel.com)

Table 1

yromeMlatoT 1MMID 2MMID 3MMID 4MMID

BG1= mumixaM

MARDS/ODE BM23,BM61,BM8 M652,BM821,BM46 1X

MARDS/ODE ,BM23,BM61,BM8 BM652,BM821,BM46 1X

BM867= mumixaM

MARDS/ODE BM23,BM61,BM8 M652,BM821,BM46 1X

MARDS/ODE ,BM23,BM61,BM8 BM652,BM821,BM46 1X

enoN

BM215= mumixaM

MARDS/ODE ,BM23,BM61,BM8 BM652,BM821,BM46 1X

enoNenoN

BM652=

mumixaM

MARDS/ODE

,BM23,BM61,BM8

BM652,BM821,BM46

enoNenoNenoN

noitpOMARDS epyTtnenopmoCMARDS

BM861xM1

BM6123xM2ro8xM2

BM23*4xM4ro61xM4

BM468xM8

BM821*4xM61

Table 2

* Registered DIMM only.

Installation BXB

Page 8

Device Connectors

Please install the motherboard into the chassis.

Now that your motherboard is installed you are ready to connect all your connections

(figure 12).

USB 1

(Top)

USB 0

(Bottom)

PS/2 Mouse

(Top)

PS/2 Keyboard

(Bottom)

Parallel Port

(Top)

Com1 Com2

(Bottom Left) (Bottom

Right)

FDD1:Floppy controller

IDE1:Primary IDE

IDE2:Secondary IDE

J1: SB-Link

J2/J3:Chassis panel connector

(Keylock, Speaker, Reset, Turbo, Sleep, and HDD LED)

J4: CPU 1 fan power (plug-in for compatible FANs which allow monitoring)

J5: CPU 2 fan power (plug-in for compatible FANs which allow monitoring)

J6: Chassis fan power (plug-in for compatible FANs which allow monitoring)

J7: Wake-On-Lan (WOL)

PW1: ATX power connector (20-pin power connector)

SCJ1:68-pin wide SCSI for legacy single-ended (SE) SCSI devices

SCJ2:50-pin narrow SCSI for legacy single-ended (SE) SCSI devices

SCJ3:68-pin wide SCSI for Ultra-2 LVD SCSI devices

Figure 12

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345

InstallationBXB

Page 9

Power On/Off - This is connected to the power button on the case.

Using the Soft-Off by Pwr-BTTN feature, you can choose either

Instant Off (turns system off immediately), or 4 sec delay (you need to

hold the button down for 4 seconds before the system turns off).

When the system is in 4 sec delay mode, 2theMax has added a special

feature to make the system go into suspend mode when the button is

pressed momentarily.

Device Connectors (continued)

Speaker - Connect to the system's speaker for beeping

1. Speaker 3. GND

2. N/C 4. GND

Reset - Closed to restart system.

Turbo LED indicator - LED ON when higher speed is selected

IDE LED indicator - LED ON when Onboard PCI IDE Hard disks is

activate

KeyLock - Keyboard lock switch & Power LED connector

1. Power LED(+) 4. Keylock

2. N/C 5. GND

3. GND

Infrared - Infrared connector

1. Vcc 4. GND

2. IRTX 5. IRTX2

3. IRRX2

Power On/OffIDE & TurboInfraredPwr LED & KeylockSpeakerReset

InstallationBXB

Page 10

Adaptec SCSI Setup

Introduction

The BXB motherboard features the advanced Adaptec AIC-7890 Ultra-2 Wide

SCSIcontroller.ThiscontrollerprovidessupportforLowVoltageDifferential

(LVD) SCSI devices as defined under the Ultra-2 section of the SCSI-3 standard.

LVD SCSI devices allow for data transfer rates of up to 80 Mbytes/sec and can

use cable lengths of up to 12 meters! Additionally the AIC-3860 Adaptec control-

lerisalsoprovidedforbackwardscompatibilitywithsingle-ended(SE)legacy

SCSI devices such as SCSI-1, Fast, Fast Wide, Ultra and Ultra Wide.

HardwareSetup andConnector Descriptions

The motherboard can have attached a total of 15 SCSI devices. The 15 de-

vices can be a combination of LVD Ultra-2 devices and/or SE Legacy devices

but note that the SE Legacy controller can support up to 8 devices only!

Provided on the motherboard are three SCSI connectors. The first two being SCJ1

and SCJ2 are provided for single-ended (SE) legacy SCSI devices and will oper-

ate at a data transfer rate of 40 Mbytes/sec (max.) using the 68-pin “Wide” connec-

tor and 20 Mbytes/sec (max.) using the 50-pin “Narrow” connector. It is strongly

recommended that all legacy SCSI devices be connected to either one of these two

connectors.DuetothedesigncharacteristicsofSEmodedevicesthecablelength

per connector should never exceed 3 meters with up to 4 SCSI devices and 1.5

meters with up to 8 SCSI devices.

External SCSI devices can be connected to theSCSIbus through the

use of the included “external SCSI-2 port adapter.” To use external

SCSI devices simply use onboard connector SCJ2 with an internal 50-

pin SCSI cable. One end of the cable must attach to SCJ2 and the other

end connects to the external port adapter. Internal SCSI devices can still

be used, but just not on the ends of the cable.

Inhaltsverzeichnis

Andere EPOX Hauptplatine Handbücher

EPOX

EPOX P55-VP 2 Bedienungsanleitung

EPOX

EPOX IP-4PCI2E Series Bedienungsanleitung

EPOX

EPOX EP-5BTXA-E Bedienungsanleitung

EPOX

EPOX EP-BX6 Bedienungsanleitung

EPOX

EPOX 3WXA Bedienungsanleitung

EPOX

EPOX EP-4B2AE Bedienungsanleitung

EPOX

EPOX KP6-LA Bedienungsanleitung

EPOX

EPOX MU-4PEA800 Bedienungsanleitung

EPOX

EPOX EP-MVP3G-M Bedienungsanleitung

EPOX

EPOX SiS 661FX Bedienungsanleitung

EPOX

EPOX EP-MVP3G-M Bedienungsanleitung

EPOX

EPOX EP-6VBA Bedienungsanleitung

EPOX

EPOX EP-BX3 Bedienungsanleitung

EPOX

EPOX LX370Y Bedienungsanleitung

EPOX

EPOX EP-3VB Bedienungsanleitung

EPOX

EPOX EP-MVP4G Bedienungsanleitung

EPOX

EPOX EP-6ZXM Bedienungsanleitung

EPOX

EPOX EP-5NVA+SLI Bedienungsanleitung

EPOX

EPOX 61BXA-M Bedienungsanleitung

EPOX

EPOX P2-112A Bedienungsanleitung

EPOX

EPOX kl-133m Bedienungsanleitung

EPOX

EPOX GXA486SPM Bedienungsanleitung

EPOX

EPOX 6VBA-E Bedienungsanleitung

EPOX

EPOX EP-ZX370Y Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung