Federal Signal Corporation Commander 371LED-120 Handbuch

2562671A

REV. A1 0714

Printed in U.S.A.

français...............page 17

español...............página 33

Commander® Rotating Light

Model 371LED-120

Installation and

Maintenance Manual

Warranty – Seller warrants all goods for ve years on parts and 2-1/2 years

on labor, under the following conditions and exceptions: Seller warrants that

all goods of Seller's manufacture will conform to any descriptions thereof

for specications which are expressly made a part of this sales contract and

at the time of sale by Seller such goods shall be commercially free from

defects in material or workmanship. Seller reserves the right at the Seller’s

discretion to “Repair and Return” or “Replace” any item deemed defective

during the warranty period. This warranty does not cover travel expenses,

the cost of specialized equipment for gaining access to the product, or labor

charges for removal and reinstallation of the product. This warranty shall be

ineffective and shall not apply to goods that have been subjected to misuse,

neglect, accident, damage, improper maintenance, or to goods altered or

repaired by anyone other than Seller or its authorized representative, or if

ve years have elapsed from the date of shipment of the goods by Seller with

the following exceptions: lamps and strobe tubes are not covered under this

warranty. Outdoor warning sirens and controllers manufactured by Federal

Warning Systems are warranteed for two years on parts and one year on labor.

No agent, employee, representative or distributor of Seller has any authority

to bind the Seller to any representation, afrmation, or warranty concerning

the goods and any such representation, afrmation or warranty shall not be

deemed to have become a part of the basics of the sales contract and shall

be unenforceable. THE FOREGOING WARRANTIES ARE EXCLUSIVE

AND IN LIEU OF ALL OTHER WARRANTIES OR MERCHANTABILITY,

FITNESS FOR PURPOSE AND OF ANY OTHER TYPE, WHETHER

EXPRESS OR IMPLIED. These warranties shall not apply unless Seller

shall be given reasonable opportunity to investigate all claims for allegedly

defective goods. Upon Seller's instruction a sample only of allegedly defective

goods shall be returned to Seller for its inspection and approval. The basis of

all claims for alleged defects in the goods not discoverable upon reasonable

inspection thereof pursuant to paragraph 8 hereof must be fully explained

in writing and received by Seller within thirty days after Buyer learns of the

defect or such claim shall be deemed waived.

Industrial Systems

2645 Federal Signal Drive • University Park, IL 60484-3167

Tel: 708-534-4756 • Fax: 708-534-4852

Email: [email protected] • www.federalsignal-indust.com

Model 371LED-120 Rotating Light

Figures

Figure 1 Beam with 22.5- and 90-degree reectors......................... 7

Figure 2 Mounting options................................................................8

Figure 3 Installing the 22.5-degree reector.................................... 10

Figure 4 Connecting leads to the terminal block.............................12

Contents

Safety Messages to Installers ..........................................................5

An Overview of the Model 371LED-120 ...........................................6

Unpacking the Light.......................................................................... 6

Mounting the Light ............................................................................8

Pipe Mounting the Light .......................................................... 8

Surface Mounting the Light ..................................................... 9

Installing the Optional 22.5-Degree Reector................................. 9

Wiring the Light ............................................................................... 11

Safety Messages to Maintenance Personnel................................ 13

Maintaining the Model 371LED-120 ...............................................13

Getting Service, Assistance, and Parts......................................... 14

Repair Service ....................................................................... 14

Technical Assistance ............................................................... 14

Accessories and Replacement Parts ....................................... 14

Returning the Product for Credit ...................................................16

Model 371LED-120 Rotating Light

Contents

Tables

Table 1 Electrical and environmental ratings ..................................... 7

Table 2 Dimensions............................................................................ 7

Table 4 Replacement parts .............................................................. 15

Table 5 Accessories ......................................................................... 15

Installation and Maintenance Instructions

Model 371LED-120 Rotating Light

Safety Messages to Installers

It is important to follow all instructions shipped with this product.

This device is to be installed by a trained electrician who is

thoroughly familiar with the National Electrical Code and/or

Canadian Electrical Code and will follow the NEC and/or CEC

Guidelines as well as all local codes. This light should be considered

a part of the warning system and not the entire warning system.

The selection of the mounting location for the light, its controls

and the routing of the wiring are to be accomplished under the

direction of the facilities engineer and the safety engineer. In

addition, listed below are some other important safety instructions

and precautions you should follow:

• Read and understand all instructions before installing or

operating this light.

• Do not connect this light to the system when power is on.

• After installation, make sure that all set screws and threaded

joints are properly tightened.

• To be an effective warning device, this product produces bright

light that can be hazardous to your eyesight when viewed at a

close range. Do not stare directly into this lighting product at a

close range or permanent damage to your eyesight may occur.

• After installation, test the light to make sure that it is

operating properly.

• After testing is complete; provide a copy of this instruction

booklet to all personnel.

• Establish a procedure to routinely check the light for proper

activation and operation.

Failure to follow all safety precautions and instructions may result

in property damage, serious injury, or death.

Installation and Maintenance Instructions

Model 371LED-120 Rotating Light

An Overview of the Model 371LED-120

Federal Signal Model 371LED-120 warning light incorporates

an array of high power LEDs, a custom optic, and a rotating

reector to focus a beam of light that rotates 360 degrees within

|a plastic dome.

The Model 371LED-120 features a impact-resistant plastic dome.

The Model 371LED is available in ve colors: amber, blue, clear,

green, and red. The dome-and-ring assembly screws on, providing

access to the interior of the light. The base features textured black

powder paint for greater corrosion-resistance. Wiring can be routed

through the pipe-mount opening in the bottom of the light or the

two side knockouts can be used for side entry wiring. Installation

can be surface or 1-inch NPT pipe mount.

An optional reector is available that reects the light beam at

22.5 degrees from the vertical orientation for overhead mounting

and other applications. See Figure 1 on page 7.

Also available is an optional wall-mount bracket. The LHWB

wall-mount bracket can be used to mount the Model 371LED. For

surface mounting on solid substrates, the separately purchased

Model 371BRCKT three-point surface-mount bracket is available.

Unpacking the Light

After unpacking the light, examine it for damage that may

have occurred in transit. If the light has been damaged, do not

attempt to install or operate it. File a claim immediately with

the carrier, stating the extent of the damage. Carefully check all

envelopes, shipping labels, and tags before removing or discarding

them. Disposal of all shipping materials must be carried out in

accordance with national and local codes and standards. If any

parts are missing, please call Federal Signal Customer Support at

708-534-4756.

Installation and Maintenance Instructions

Model 371LED-120 Rotating Light

Figure 1 Beam with 22.5- and 90-degree reectors

BEAM FROM OPTIONAL

22.5-DEGREE REFLECTOR

290A6862

BEAM FROM STANDARD

90-DEGREE REFLECTOR

Table 1 Electrical and environmental ratings

Operating Voltage: 120 Vac 50 Hz/60 Hz

Flash Rate: 60 FPM

Maximum Operating

Current, mA:

320 mA

In-rush Current: 25.1 A for 0.63 ms

Operating

Temperature:

-31°F to 104°F (-35°C to 40°C)

Environmental

Ratings:

Type 4X, IP66

Table 2 Dimensions

Height: 11.38 in (288.9 mm)

Diameter: 9.12 in (231.6 mm)

Net Weight: 7.1 lb (3.2 kg)

Shipping Weight: 8.1 lb (3.7 kg)

Installation and Maintenance Instructions

Model 371LED-120 Rotating Light

Mounting the Light

The Model 371LED-120 light is designed for mounting on a at

horizontal surface or on a 1-inch NPT pipe. For surface mounting on

solid substrates, the separately purchased Model 371BRCKT surface

mounting bracket can be used. If conduit side-entries are to be used,

disassemble the light as described in “Wiring the Light” on page 11

and remove one or more knockouts with a blunt tool before mounting

the light. Use a le to remove excess ash around the knockout.

INSTALLATION NOTE: To avoid moisture buildup within the

light enclosure in highly humid areas where condensation is present

in the conduit system, duct sealant or other suitable materials are

recommended for sealing the wires/conduit entrances.

Pipe Mounting the Light

Attach the light to the 1-inch NPT pipe by threading the light

clockwise on the pipe (Figure 2). For information on making the

electrical connections, see “Wiring the Light” on page 11.

Figure 2 Mounting options

371LED-120 LIGHT

ASSEMBLY

PIPE MOUNT SURFACE MOUNT

GASKET

MOUNTING

SURFACE

1/4" FLATWASHERS

DRILL THREE 9/32"

(7.143 mm) HOLES

1/4" SCREWS

1" NPT

PIPE

290A6859

Installation and Maintenance Instructions

Model 371LED-120 Rotating Light

Surface Mounting the Light

To mount the light on a at surface:

1. Using the gasket as a template, scribe four drill-position

marks on the mounting surface (Figure 2).

2. Drill a 9/32-inch (7.1 mm) diameter hole at each of the

outside drill-position marks for mounting.

3. Drill or punch a 1-3/8 inch (34.9 mm) diameter hole at the

center drill-position mark for the wire entry.

4. Attach a suitable 1-inch NPT hub or connector to conduit

entrance in bottom of light. For Type 4X/IP66 applications,

the hub or connector must be suitably rated (Myers®

STTTB-2 or T&B® H100-TB hubs are recommended.)

5. Set the light on the gasket and attach it to the mounting

surface with the provided 1/4-inch screws and washers.

6. For information on making the electrical connections, see

page 11.

Installing the Optional 22.5-Degree Reector

The light is shipped from the factory with the standard reector

that creates a horizontal lightbeam that is 90 degrees from the

vertical orientation. An optional reector is available that reects

the light beam at 22.5 degrees from the vertical orientation (see

Figure 1 on page 7 and “Table 4 Accessories” on page 15).

To replace the standard reector with the 22.5-degree reector:

1. Disconnect power to the light.

2. See Figure 3 on page 10. Remove the dome assembly by

grasping the die-cast ring attached to the dome and turning it

counter-clockwise.

3. Loosen the two Phillips screws that retain the reector.

Installation and Maintenance Instructions

Model 371LED-120 Rotating Light

4. Gently lift the reector from the assembly while being careful

to not drop the two screws.

5. Position the new reector onto the assembly and secure it with

the two screws.

6. Reinstall the dome assembly.

7. Reinstall power and test the light for proper operation.

Figure 3 Installing the 22.5-degree reector

290A6855

PLASTIC DOME

LED

MOTOR

MODULE

REFLECTOR

DIECAST

BASE

DIECAST RING

22.5-DEGREE

REFLECTOR

PHILLIPS SCREWS (2)

Inhaltsverzeichnis

Sprachen:

Andere Federal Signal Corporation Autozubehör Handbücher

Federal Signal Corporation

Federal Signal Corporation Spectralux Rear ILS Light Bar Handbuch

Federal Signal Corporation

Federal Signal Corporation Vista Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 7000 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation JetSolaris JLX Series Handbuch

Federal Signal Corporation

Federal Signal Corporation XHK-SD Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation ML-PT Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Viewpoint FV Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Commander 371LED-120B Handbuch

Federal Signal Corporation

Federal Signal Corporation HighLighter Montageanleitung

Federal Signal Corporation

Federal Signal Corporation GH1K Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Vision SLR Original Betriebsanleitung

Federal Signal Corporation

Federal Signal Corporation ESB-CRG07 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation GHSCENE Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation CUDA TRIOPTIC 351011 Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Commander 371LED-120A Handbuch

Federal Signal Corporation

Federal Signal Corporation RAYDIAN Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VSLR1-IPX Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Legend Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SIFMH Handbuch

Federal Signal Corporation

Federal Signal Corporation ESB-IMP08R Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation CAMLCD-AHD-70 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SpectraLux SIFZJ FSJoin Handbuch

Federal Signal Corporation

Federal Signal Corporation Cuda TriOptic SIGNALMASTER 328823F Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation DFC-WC-DUR21 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung