Federal Signal Corporation XStream XSM Series Kurzanleitung

Installation and Service Instructions

25500381

Rev A5 0822

Printed in U.S.A.

XStream®Interior Light

Models XSMxx-xxx

Safety Messages

XStream®Model XSMxx-xxx

Federal Signal www.fedsig.com

Safety Messages

Safety Messages to Installers and Users of Warning Light Equipment

People’s lives depend on your proper installation and operation of Federal Signal

products. It is important to read and follow all instructions shipped with this

product and the original product. Listed below are some other important safety

instructions and precautions you should follow:

• To properly install this light, you must have a good understanding of

automotive electrical procedures and systems, along with proﬁciency in the

installation and service of safety warning equipment. Always refer to the

vehicle’s service manuals when installing equipment on a vehicle.

• DO NOT install equipment or route wiring in the deployment path of an airbag.

• When drilling into a vehicle structure, ensure that both sides of the surface are

clear of anything that could be damaged.

• For the light to function properly, a separate ground connection must be

made. If practical, it should be connected to the negative battery terminal.

At a minimum, it may be attached to a solid metal body or chassis part that

provides an eective ground path.

• Locate the light control so the VEHICLE and CONTROL can be operated safely

under all driving conditions.

• The eectiveness of an interior mounted warning light depends on the clarity,

the tinting, and the angle of the glass it is placed behind. Tinting, dirt, defects,

and steeply angled glass reduce the light output of the warning light. This may

reduce the eectiveness of the light as a warning signal. If your vehicle has dirty,

tinted, or steeply angles glass, use extra caution when driving your vehicle or

blocking the right of way with your vehicle.

• Do not attempt to activate or deactivate the light control while driving in a

hazardous situation.

• Frequently inspect the light to ensure that it is operating properly and that it is

securely attached to the vehicle.

• This product contains high-intensity LED devices. To prevent eye damage, DO

NOT stare into the light beam at close range.

• After installation, test the lights to ensure that they are operating properly.

• If a vehicle seat is temporarily removed, verify with the vehicle manufacturer if

the seat needs to be recalibrated for proper airbag deployment.

Product Overview

Installation and Service Instructions

Federal Signal www.fedsig.com

• After testing is complete, provide a copy of these instructions to the

instructional sta and all operating personnel.

• File these instructions in a safe place and refer to them when maintaining and/or

reinstalling the product.

Failure to follow all safety precautions and instructions may result in property

damage, serious injury, or death.

Product Overview

The SpectraLux®XStream®LED Series light heads are low-current warning lights

that are mounted only on the inside of the vehicle. The light head uses Solaris®

LED reﬂector technology to provide a bright and eective secondary warning

signal. XStream models have 18 LEDs per head that can be ordered in various

color combinations with a clear lens. Wire lead (Sync) and accessory plug models

are available.

All XStream models are designed for use with all Federal Signal switch controllers.

The XStream is supplied with hardware for mounting the light head horizontally

on the vehicle deck or dash. Additional bracket kits are available. The light heads

have an operating temperature of –30º C to +65º C (–22º F to +149º F).

Unpacking the Product

After unpacking the product, inspect it for damage that may have occurred in

transit. If it has been damaged, do not attempt to install or operate it. File a claim

immediately with the carrier, stating the extent of damage. Carefully check all

envelopes, shipping labels, and tags before removing or destroying them. Ensure

that the parts in the Kit Contents list are included in the package. If you are

missing any parts, contact Customer Support at 1-800-264-3578, 7 a.m. to 5 p.m.,

Monday through Friday (Central Time).

Table 1 XStream Single Kit Contents*

Qty. Description Part Number

1 Visor, Long Single 861301423

1 Visor, Medium, Single 861301922

1 Visor, Short, Single 861301923

2Screw, #8, 48-2, Plastite Equivalent, 6-Lobe, Steel,

Black, Zinc 70000705-05

2 Screw, #10, Type B, Pan-Head,TORX Steel, Black, Zinc 7011246-06

2 Lockwasher, #10, Internal Tooth, Steel 7075A014

2 Suction Cup 8613121

1 Bail Bracket 861301751

1 Pivot Bracket 861301910

Unpacking the Product

XStream®Model XSMxx-xxx

Federal Signal www.fedsig.com

Table 2 XStream®Dual Kit Contents*

Qty. Description Part Number

1 Visor, Long Dual 861301424

1 Visor, Medium, Dual 861301924

1 Visor, Short, Dual 861301925

2Screw, #8, 48-2, Plastite Equivalent, 6-Lobe, Steel,

Black, Zinc 70000705-05

2 Screw, #10, Type B, Pan Head,TORX Steel, Black, Zinc 7011246-06

2 Lockwasher, #10, Internal Tooth, Steel 7075A014

2 Suction Cup 8613121

1 Bail Bracket 861301751

1 Bracket, Pivot 861301910

*User-supplied hardware is required to permanently mount the light

Figure 1 XStream suction cup mounting

Bail

Bracket

Pivot

Bracket

Suction

Cup (2)

#10 Pan Head

Screw (2)

Lock Washer (2)

#8 Pan Head

Screw (2)

Visor

Installing the Light Heads

Installation and Service Instructions

Federal Signal www.fedsig.com

Figure 2 XStream bracket-mounting

Visor

#8 Pan Head

Screw (2)

#10 Pan Head

Screw (2)

Lockwasher (2)

Bail

Bracket

Pivot

Bracket

Installing the Light Heads

AIRBAG DEPLOYMENT: Do not install equipment or route wiring in the

deployment path of an airbag. Failure to observe this warning will reduce the

effectiveness of the airbag or potentially dislodge the equipment, causing

serious injury or death.

LIGHT OUTPUT COMPLIANCE: This product is intended for supplemental

warning in conjunction with an approved primary warning light system.

Consult local codes and regulations to determine if the power supply/light

head combination complies with the horizontal or vertical mount position

required in your application. Failure to follow this warning could result in

reducing the light output and its effectiveness as a warning system.

LIGHT HAZARD: To be an effective warning device, this product produces

bright light that can be hazardous to your eyesight when viewed at a close

range. Do not stare directly into this lighting product at a close range, or

permanent damage to your eyesight may occur.

Before installing the lights, read all instructions and plan all wiring and cable

routing. To secure and protect the wiring, use grommets, wire ties, looms, and

cable mounts (installer-supplied) as needed.

Mounting the Light Head in a Vehicle

XStream®Model XSMxx-xxx

Federal Signal www.fedsig.com

To install the light heads:

1. Optional: Set a light head to control the ﬂash patterns of one or more light

heads in the XStream®system.

2. Mount the XStream system to the vehicle. See Mounting the Light Head in a

Vehicle below.

3. Wire the XStream system to the vehicle.

4. Select a ﬂash pattern for the controller light head.

Mounting the Light Head in a Vehicle

The light is installed using the supplied bracket and screws or suction cups.

Determine the mounting position appropriate for the installation, and then select

the applicable mounting method.

Mounting the Light with Suction Cups

SUCTION CUPS ARE FOR TEMPORARY USE ONLY: Suction cup mounting

is for temporary applications only. This unit should be removed from the

vehicle and stored securely when not in use. Temperature changes and

sunlight can cause suction cups to lose holding power. Periodically check

the unit to ensure that the suction cups have a rm grip on the mounting

surface. An improperly secured light could fall off the windshield, causing

injury and damage.

To mount the light with suction cups:

1. Attach the appropriate visor to the light head. Press the visor ﬁrmly until it

snaps into place. See Figure 1 on page 4.

2. Attach the suction cups to the bracket.

3. Attach the pivot bracket to the light head using the supplied #8 pan-head

screws. Do not overtighten.

4. Attach the bail bracket to the pivot bracket with the supplied #10 pan-head

screws and lockwashers. The lockwashers go between the bail and the pivot

bracket.

5. Apply the suction cups to the glass.

Wiring and Programming the Light

Installation and Service Instructions

Federal Signal www.fedsig.com

Mounting the Light with the Bracket

To mount the light with a bracket:

1. Select a mounting location for the light and best orientation of the brackets.

2. Attach the appropriate visor to the light head. Press the visor ﬁrmly to snap it

into place. See Figures 1 and 2 starting on page 4.

3. Attach the pivot bracket to the light head using the supplied #8 pan head

screws. Do not overtighten.

4. Attach the bail bracket to the pivot bracket with the supplied #10 pan head

screws and lockwashers. The lockwashers go between the bail and the pivot

bracket.

5. Attach the bail bracket to the vehicle using the appropriate user-supplied

hardware.

Wiring and Programming the Light

XStream®lights are available as accessory plug or synchronizable models.

Wire Functions of Cigarette Plug Models

RED WIRE: Memory 1 (to + Vdc) (red switch on cigarette plug)

WHITE WIRE: Steady Flood (to +Vdc) (green switch on cigarette plug)

Dual head only: Press S1 to change which heads are steady ﬂood.

Accessory plug models are distinguished by the letter C in the part number.

Wire Functions of Synchronizable Models

Sync models have three additional wires:

BROWN WIRE: Memory 2 (to +Vdc)

GREEN WIRE: Sync/Program

To synchronize the lights, set them to the same color mode and ﬂash pattern and

connect the green wires. Do not sync patterns 8, 9, or 10.

BLACK WIRE: GND (to – chassis ground)

Conguring the Light

XStream®Model XSMxx-xxx

Federal Signal www.fedsig.com

Color Designations

The color codes in the model number correspond to the colors listed below:

For example Model XSM1-BRW

COLOR1 = B(Blue)

COLOR2 = R(Red)

COLOR3 = W(White)

Code List: B= Blue, R= Red, W= White, A= Amber, G= Green

Conguring the Light

Two recessed switches in the side of the housing enable you to conﬁgure how the

light operates. Switch S1 displays and sets the ﬂash pattern. Switch S2 displays and

sets the color mode. You can also conﬁgure the light for Low Power Mode. A small

precision screwdriver or paperclip is required to access the switches. See Figure 3.

Figure 3 Recessed switch locations in housing

S1 Selector Switch

For Flash Pattern

S2 Selector

Switch For Color

To select an action in Table 3, press S1 for the duration listed in the Seconds column.

To conﬁrm your selection, the LEDs respond as shown in the table. For a list of ﬂash

patterns, see Table 4.

Table 3 S1 Flash Pattern Selection Switch

Seconds COLOR 1 LED

Response

Action

0–1 Bright Next Pattern

1–3 Dim Previous Pattern

3–5 Low *Low Power

5+ Bright Reset to Pattern 1

*Low Power Mode is disabled when the operator switches to another ﬂash pattern.

Conguring the Light

Installation and Service Instructions

Federal Signal www.fedsig.com

USE THE DIMMING/LOW POWER FUNCTION PROPERLY: Enabling the

Low Power function in the light bar may cause the light output to fall below

certain light output standards and guidelines for emergency warning lights.

Use extreme caution when using this function. Ensure that the ambient

light conditions are low enough that you are seen and that the reduction of

glare from the light bar is safer than full light output in the situation. Failure

to heed this warning may result in serious injury or death to you or others

in your vicinity.

Table 4 Flash patterns

1 Triple 92.3 14 Double 120*

2 Triple 90 15 Triple 80*

3 Single 122 16 Triple 120*

4 Single 75* 17 Quad 60*

5 Single 90* 18 Quad 75*

6 Single 113* 19 Quad 95*

7 Cruise w/ Flicker 20 FedPulse Quad 75*

8Random Time 21 Quint 75*

9 Random Common* 22 7X

10 Steady 23 Single Quad*

11 Single 75* 24 Decelerating

12 Single 120*

25 Accelerating

13 Double 80*

*Conforms to California Title 13

Table 5 S2 Flashing Modes

Seconds COLOR 2 LED Response Action

0–1 Bright Next COLOR Mode

1–3 Dim Previous COLOR mode

3–5 Low Toggle Sync Simultaneous, Alternate

5–7 Bright Toggle Pattern All, Split**

7–9 Dim Swap Colors (COLOR Modes 5, 6, 7, 8, 9, and 10)

9+ Low Reset Switch 2 settings to default

**Pattern 17 (Steady Half 75) is split by default. No split option for

FedPulse 75 and Cruise patterns

Instructions to Use with Flash Pattern Helper

XStream®Model XSMxx-xxx

Federal Signal www.fedsig.com

Table 6 S2 Color Modes

Color

Mode

Single Head Dual Head 1 Dual Head 2 Description

1Color 1, 2, 3 Color 1, 2, 3 Color 1, 2, 3 Heads ash COLOR1, COLOR2,

and COLOR3

2Color 1 Color 1 Color 1 Heads ash COLOR1

3Color 2 Color 2 Color 2 Heads ash COLOR2

4Color 3 Color 3 Color 3 Heads ash COLOR3

5Color 1, 2 Color 1, 2 Color 1, 2 Heads ash COLOR1 and

COLOR2***

6Color 1, 3 Color 1, 3 Color 1, 3 Heads ash COLOR1 and

COLOR3***

7Color 2, 3 Color 2, 3 Color 2, 3 Heads ash COLOR2 and

COLOR3***

8Color 1

(duplicates 2)

Color 1 Color 2 Head 1 ashes COLOR1, Head 2

ashes COLOR2***

9Color 1

(duplicates 2)

Color 1 Color 3 Head 1 ashes COLOR1, Head 2

ashes COLOR3***

10 Color 2

(duplicates 3)

Color 2 Color 3 Head 1 ashes COLOR2, Head 2

ashes COLOR3***

***Use Swap Colors function to reverse. (Table 5).

Instructions to Use with Flash Pattern Helper

For the ﬂash pattern, connect the SYNC/green wire to the FP port:

1. Set the MODE to AUTO.

2. Set the ﬂash pattern number to the desired setting. See Table 4 on

page9.

3. Press START.

For other settings:

1. Set the Mode to AUTO.

2. Set the ﬂash pattern number to the desired setting. see Table 7 on

page11.

3. Press START.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Federal Signal Corporation Beleuchtungsausrüstung Handbücher

Federal Signal Corporation

Federal Signal Corporation JET JLX Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SIGNALMASTER SML6-2SML1F Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SLR LED Handbuch

Federal Signal Corporation

Federal Signal Corporation GH1 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VITALITE 121 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SIGNALMASTER SM518A-24 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Cuda TriOptic 351011F Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Cuda Trioptic 352012 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Global Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MicroPulse SignalMaster Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 151XST Series Handbuch

Federal Signal Corporation

Federal Signal Corporation QuadraFlare QL64-TURN Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation 371DST Handbuch

Federal Signal Corporation

Federal Signal Corporation Vision SLR Series Handbuch

Federal Signal Corporation

Federal Signal Corporation G-STR-024-D-C Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation FireRay Scene Light Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Signalmaster 330103 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Global Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation QUADRAFLARE QL97LEDSCENE Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SIGNALMASTER SM518A Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Vision SLR Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Cuda TriOptic 351012F Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Integrity Series Handbuch

Federal Signal Corporation

Federal Signal Corporation NightSpire Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung