Federal Signal Corporation Vision SLR Series Handbuch

2562540

REV. C4 0820

Printed in U.S.A.

Installation, Maintenance,

and Service Manual

Vision®SLR Light Bar

blank page

Limited Warranty

This product is subject to and covered by a limited warranty,

a copy of which can be found at www.fedsig.com/SSG-Warranty.

A copy of this limited warranty can also be obtained by written

request to Federal Signal Corporation, 2645 Federal Signal Drive,

University Park, IL 60484, email to [email protected] or

call +1 708-534-3400.

This limited warranty is in lieu of all other warranties, express or

implied, contractual or statutory, including, but not limited to the

warranty of merchantability, warranty of tness for a particular

purpose and any warranty against failure of its essential purpose.

2645 Federal Signal Drive

University Park, Illinois 60484-3167

www.fedsig.com

Customer Support

Police/Fire-EMS: 800-264-3578 • +1 708 534-3400

Work Truck: 800-824-0254 • +1 708 534-3400

Technical Support 800-433-9132 • +1 708 534-3400

All registered trademarks are properties of their respective owners.

Installation, Maintenance, and Service Manual

Federal Signal www.fedsig.com

Contents

Safety Messages.............................................................................................................................. 6

Safety Message to Installers and Service Personnel of Warning Lights...........................................6

Safety Message to Operators of Warning Light Equipment.................................................................9

An Overview of the Vision SLR Light Bar ................................................................................... 11

LED Lights and Colors ................................................................................................................................... 11

LED Flash Rates and Positions.................................................................................................................... 11

Modular Connector System (Optional)...................................................................................................... 11

Controller Options ......................................................................................................................................... 12

Operating Temperature................................................................................................................................ 12

Preparing the Vision SLR for Installation ................................................................................... 13

Unpacking the Light Bar .............................................................................................................................. 13

Connecting the Vision SLR for Programming......................................................................................... 13

Selecting External SignalMaster Control................................................................................................. 15

Selecting Internal SignalMaster Control (Factory Default).................................................................. 15

Entering Program Mode............................................................................................................................... 17

Exiting Program Mode.................................................................................................................................20

Wiring the Vision SLR in the Vehicle .......................................................................................... 21

Planning the Electrical Installation............................................................................................................. 21

Connecting Power to the Light Bar ......................................................................................................... 23

Installing the Serial Interface Module...................................................................................................... 23

Wiring the Serial Interface Module...........................................................................................................25

Maintaining and Servicing the Vision SLR ................................................................................. 36

Cleaning the Light Bar Domes .................................................................................................................. 36

Replacing a Dome ........................................................................................................................................ 37

Replacing a Pod ............................................................................................................................................ 38

Replacing an LED Alley Light..................................................................................................................... 39

Removing and Replacing the Light Bar Cover ....................................................................................... 41

Removing and Reinstalling the SignalMaster........................................................................................ 42

Servicing the SignalMaster ........................................................................................................................ 43

Replacing the Light Bar Controller ........................................................................................................... 45

Quick Disconnect Option for Power and CAT5 .................................................................................... 46

Troubleshooting the Light Bar................................................................................................................... 49

Quick Testing the Vision SLR with the Light Bar Test..........................................................................50

Testing the Steady Burn LEDs (HotFoot Only) ....................................................................................... 51

Getting Technical Support and Service....................................................................................... 51

4Vision SLR Light Bar

Federal Signal www.fedsig.com

Figures

Figure 1 Serial Interface Module connections for programming ........................................................... 14

Figure 2 Connectors and switches on the Serial Interface Module ..................................................... 18

Figure 3 Relay-isolating devices with large ﬁlter capacitors ................................................................. 25

Figure 4 Wiring block diagram ...................................................................................................................... 25

Figure 5 SignalMaster ﬂash sequences...................................................................................................... 28

Figure 6 SignalMaster control functions wired to 12 Vdc for internal Serial Interface Module con-

trol ..........................................................................................................................................................................29

Figure 7 SignalMaster control functions wired to 12 Vdc for internal Serial Interface Module con-

trol .......................................................................................................................................................................... 30

Figure 8 Typical connections with a SignalMaster controller (external control)................................ 31

Figure 9 Typical connections with a SW400SS Switch Module (internal control) ........................... 32

Figure 10 Typical connections with a SmartSiren Model SS2000SM controller.............................. 33

Figure 11 Typical connections with a non-SignalMaster controller....................................................... 34

Figure 12 Typical connections with a PA640 controller.......................................................................... 35

Figure 13 Dome removal and replacement................................................................................................ 37

Figure 14 Pods 1 and 5 rotated counterclockwise for removal ............................................................. 39

Figure 15 Alley light removal: exploded view ............................................................................................ 40

Figure 16 Screws securing the light bar cover ........................................................................................... 41

Figure 17 Screws securing the SignalMaster............................................................................................. 42

Getting Repair Service.................................................................................................................................. 51

Ordering Replacement Parts ..................................................................................................................... 52

Tables

Table 1 Dimensions ........................................................................................................................................... 12

Table 2 Light Speciﬁcations ........................................................................................................................... 12

Table 3 Electrical Speciﬁcations.................................................................................................................... 12

Table 4 SW2 DIP switch settings in the Serial Interface Module.......................................................... 16

Table 5 Control wires from the Serial Interface Module......................................................................... 17

Table 6 Switch settings for Intersection operation .................................................................................20

Table 7 SignalMaster control wires and warning patterns ................................................................... 28

Table 8 Troubleshooting tips ........................................................................................................................ 49

Table 9 Replacement parts............................................................................................................................52

Installation, Maintenance, and Service Manual

Federal Signal www.fedsig.com

Figure 18 SignalMaster removed from the light bar................................................................................. 43

Figure 19 SignalMaster disassembled......................................................................................................... 44

Figure 20 Controller connectors................................................................................................................... 45

Figure 21 Controller location beneath light bar cover............................................................................. 46

Figure 22 Locations of watertight connectors .......................................................................................... 46

Figure 23 Secondary lock mechanism in the plug and receptacle..................................................... 47

6Vision SLR Light Bar

Federal Signal www.fedsig.com

Safety Messages

For your safety, read and understand this manual thoroughly before installing,

operating, and servicing the Vision SLR light bar. The safety messages presented in

this section and throughout the manual are reminders to exercise extreme care at all

times. To download copies of the manual, go to www.fedsig.com or call the Federal

Signal Service Department at 1-800-433-9132, 7 a.m. to 5 p.m., Monday through Friday

(CT).

Safety Message to Installers and Service Personnel of Warning Lights

People’s lives depend on your proper installation and servicing of Federal Signal

products. It is important to read and follow all instructions shipped with this product.

Listed below are some other important safety instructions and precautions you should

follow.

Before Installation or Service

Qualiﬁcations

• To properly install or service this equipment, you must have a good understanding

of automotive mechanical and electrical procedures and systems, along with

proﬁciency in the installation and service of safety warning equipment. Always

refer to the vehicle service manuals when performing equipment installations on a

vehicle.

Light Hazards

• To be an eective warning device, this product produces bright light that can be

hazardous to your eyesight when viewed at a close range. Do not stare directly

into this lighting product at a close range, or permanent damage to your eyesight

may occur.

• Do not install the light system in an area that would block, impair, or blind the

driver’s vision. Ensure that the light system is mounted in a position that is outside

of the driver’s ﬁeld of vision, so the driver can safely operate the vehicle.

• Federal Signal power supplies and light heads are designed to work together as

a system. Combining light heads and a power supply from dierent manufacturers

may reduce the warning eectiveness of the lighting system and may damage

the components. Verify or test your combination to ensure that the system works

together and meets federal, state, and local standards or guidelines.

Electrical Hazards

• Strobe systems present a shock hazard because they use high voltage to operate.

Do not handle strobe cables, the power supply, or bulbs or remove the lens while

the equipment is connected. Strobe systems can also hold their charge even after

they have been turned o. After disconnecting power to the unit, wait ﬁve minutes

before handling any parts of the strobe system.

Installation, Maintenance, and Service Manual

Federal Signal www.fedsig.com

Safety Messages

• A light system is a high current system. In order for the system to function

properly, a separate negative (–) connection and positive (+) connection must

be made. All negative connections should be connected to the negative battery

terminal and a suitable fuse should be installed on the positive battery terminal

connection as close to the battery as possible. Ensure that all wires and fuses are

rated correctly to handle the device and system amperage requirements.

• Never attempt to install aftermarket equipment that connects to the vehicle wiring

without reviewing a vehicle wiring diagram available from the vehicle manufacturer.

Ensure that your installation will not aect vehicle operation or mandated

safety functions or circuits. Always check the vehicle for proper operation after

installation.

• The lighting system components, especially light bulbs, strobe tubes, LEDs, and

the outer housing, get hot during operation. Be sure to disconnect power to the

system and allow the system to cool down before handling any components of the

system.

• Halogen light bulbs and strobe tubes are pressurized and, if broken, can burst and

result in ﬂying glass. Always wear gloves and eye protection when handling these

components.

• Do not mount a radio antenna within 18 inches (45.7 cm) of the lighting system.

Placing the antenna too close to the lighting system could cause the lighting

system to malfunction or be damaged by strong radio ﬁelds. Mounting the

antenna too close to the lighting system may also cause the radio noise emitted

from the lighting system to interfere with the reception of the radio transmitter and

reduce radio reception.

• Do not attempt to wash any unsealed electrical device while it is connected to its

power source.

During Installation and Service

• DO NOT get metal shavings inside the product. Metal shavings in the product

can cause the system to fail. If drilling must be done near the unit, place an ESD-

approved cover over the unit. Inspect the unit after mounting to be sure there are

no shavings present in or near the unit.

• To avoid a battery explosion, always disconnect the negative battery cable ﬁrst

and reconnect it last. Avoid causing a spark when connecting near or to the

battery. The gases produced by a battery can caused a battery explosion that

could result in vehicle damage and serious injury.

• DO NOT connect this system to the vehicle battery until ALL other electrical

connections are made, mounting of all components is complete, and you have

veriﬁed that no shorts exist. If the wiring is shorted to the vehicle body or frame,

high current conductors can cause hazardous sparks resulting in electrical ﬁres or

ﬂying molten metal.

• DO NOT install equipment or route wiring (or the plug in cord) in the deployment

path of an airbag.

8Vision SLR Light Bar

Federal Signal www.fedsig.com

Safety Messages

• If a vehicle seat is temporarily removed, verify with the vehicle manufacturer if the

seat needs to be recalibrated for proper airbag deployment.

• Before mounting any components, check the manual to be sure that the

component you are installing is suitable for use in that area of the vehicle. Many

components are not suitable for use in the engine compartment or other extreme

environmental exposure areas.

• The service life of light bulbs and strobes tubes will be shortened if the

glass portion is touched during installation. Use gloves when handling these

components. If the glass portion has been touched, clean the glass carefully with

isopropyl alcohol.

• When drilling into a vehicle structure, ensure that both sides of the surface are

clear of anything that could be damaged. Remove all burrs from drilled holes. To

prevent electrical shorts, grommet all drilled holes through which wiring passes.

Also, ensure that the mounting screws do not cause electrical or mechanical

damage to the vehicle.

• Refer to the manual packed with the lighting system for proper electrical

connections, additional precautions, and information.

• Because vehicle roof construction and driving conditions vary, do not drive a

vehicle with a magnetically mounted warning light installed. The light could ﬂy

o the vehicle, causing injury or damage. Repair of damage incurred because of

ignoring this warning shall be the sole responsibility of the user.

• To avoid denting the roof of the vehicle, place the light bar mounting feet as close

to the outer edge of the roof as possible.

• Roof damage can occur if the hook adjustment bolts are overtightened. Tighten

the adjustment bolts to 6 ft-lb to 7 ft-lb. Install keeper plates.

• Locate the light system controls so the VEHICLE and CONTROLS can be operated

safely under all driving conditions.

After Installation or Service

• After installation, test the light system to ensure that it is operating properly.

• To ensure proper operation, test all vehicle functions, including horn operation,

vehicle safety functions, and vehicle light systems. Ensure that the installation

has not aected the vehicle operation or changed any vehicle safety function or

circuit.

• Scratched or dull reﬂectors, mirrors, or lenses will reduce the eectiveness of

the lighting system. Avoid heavy pressure and use of caustic or petroleum-based

products when cleaning the lighting system. Replace any optical components that

may have been scratched or crazed during system installation.

• Do not attempt to activate or deactivate the light system control while driving in a

hazardous situation.

• Frequently inspect the light system to ensure that it is operating properly and that

it is securely attached to the vehicle.

Installation, Maintenance, and Service Manual

Federal Signal www.fedsig.com

Safety Messages

• After installation and testing are complete, provide a copy of these instructions to

instructional sta and all operating personnel.

• File these instructions in a safe place and refer to them when maintaining and/or re-

installing the product.

Failure to follow these precautions may result in property damage, serious injury, or

death.

Safety Message to Operators of Warning Light Equipment

People’s lives depend on your safe use of our products. Listed below are some

important safety instructions and precautions you should follow:

• Do not attempt to activate or deactivate the light system control while driving in a

hazardous situation.

• Although your warning system is operating properly, it may not be completely

eective. People may not see or heed your warning signal. You must recognize

this fact and continue to drive cautiously.

• Situations may occur that obstruct your warning signal when natural and man-

made objects are between your vehicle and others, such as raising your hood or

trunk lid. If these situations occur, be especially careful.

• The eectiveness of an interior mounted warning light depends on the clarity, the

tinting, and the angle of the glass it is being placed behind. Tinting, dirt, defects,

and steeply angled glass reduce the light output of the warning light. This may

reduce the eectiveness of the light as a warning signal. If your vehicle has dirty,

tinted, or steeply angled glass, use extra caution when driving your vehicle or

blocking the right of way with your vehicle.

• All eective sirens and horns produce loud sounds that may cause, in certain

situations, permanent hearing loss. You and your passengers should consider

taking appropriate safety precautions, such as wearing hearing protection.

• In order to be an eective warning device, this product produces bright light that

can be hazardous to your eyesight when viewed at a close range. Do not stare

directly into this lighting product at a close range or permanent damage to your

eyesight may occur.

• It is important that you fully understand how to safely operate this warning system

before use.

• Operate your vehicle and its light/sound system in accordance with your

department’s Standard Operating Procedures.

• If a selected function does not perform properly or if any of the lamps remain

illuminated when the control is o, disconnect the power connector from the control

unit and contact the nearest service center.

• At the start of your shift, ensure that the entire warning light system and the siren

system is securely attached and operating properly.

10 Vision SLR Light Bar

Federal Signal www.fedsig.com

Safety Messages

• Suction cup mounting is for temporary applications only. The unit should be

removed from the window and stored securely when not in use. Temperature

changes and sunlight can cause suction cups to lose holding power. Periodically

check the unit to be sure the suction cups have a ﬁrm grip on the mounting

surface. An improperly secured light could fall o of the vehicle, causing injury and

damage.

• Holding power of magnetic mounting systems is dependent upon surface ﬁnish,

surface ﬂatness, and thickness of the steel mounting surface. Therefore, to

promote proper magnetic mounting:

• Keep the mounting surface and magnets clean, dry, and free of foreign particles

that prevent good surface contact.

• Ensure that mounting surface is ﬂat.

• Do not use a magnet mounting system on vehicles with vinyl tops.

• To prevent sliding of light assembly on mounting surface, avoid quick

acceleration and hard stops.

Failure to follow these precautions may result in property damage, serious injury, or

death.

Andere Handbücher für Vision SLR Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Federal Signal Corporation Beleuchtungsausrüstung Handbücher

Federal Signal Corporation

Federal Signal Corporation Electraray 225 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation STREAMLINE LP3E Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation Vision SLR Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Cuda TriOptic 352012F Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Vitalite 121SLED Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation AD Series Handbuch

Federal Signal Corporation

Federal Signal Corporation QUADRAFLARE QL97LEDSCENE Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Electraray 225 Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation CudaTriOptic 352212 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation NightSpire Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation G-STR-024-D-C Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Cuda TriOptic 351012F Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation COMMANDER Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Electraray 225 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Signalmaster 330103 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation JET JLX Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MB-IDENT03 Handbuch

Federal Signal Corporation

Federal Signal Corporation Viper S2 Light Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VITALITE 121 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Vision SLR Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VIEWPOINT FVPK Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation QuadraFlare QL97HSCENE Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation QL43 Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation 371DST Handbuch

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung