Hach 2100AN IS Kurzanleitung

DOC022.97.80206

2100AN IS

05/2012, Edition 4

Basic User Manual

Manuel d'utilisation de base

Manual básico del usuario

English...................................................................................................................................................................................................3

Français..............................................................................................................................................................................................20

Español...............................................................................................................................................................................................38

Table of contents

Specifications on page 3 Standard operation on page 11

General information on page 4 Maintenance on page 16

User interface on page 8 Troubleshooting on page 17

Startup on page 10

Specifications

Specifications are subject to change without notice.

Specification Details

Measurement method Nephelometric

Regulatory Meets ISO 7027, DIN EN 27027, DIN 38404 and NFT

9033

ASTM D7315 - Standard Test Method for

Determination of Turbidity Above 1 Turbidity Unit (TU)

in Static Mode

ASTM D6655 - Standard Test Method for

Determination of Turbidity Below 5 NTU in Static Mode

Light source Light-emitting diode (LED) at 860 ± 30 nm

Measurement modes FNU, FAU, NTU, EBC, Abs (absorbance), %T (%

transmittance) and two user-defined units

Specification Details

Range FNU (manual range): 0–0.999, 0–9.99, 0–99.9,

0–1000

FNU (auto range): 0–1000

FAU (manual range): 20–99.9, 20–10,000

FAU (auto range): 20–10,000

NTU (Ratio on, manual range): 0–0.999, 0–9.99,

0–99.9, 0–10,000

NTU (Ratio on, auto range): 0–10,000 auto decimal

NTU (Ratio off): 0–40

EBC (Ratio on, manual range): 0–0.999, 0–9.99,

0–99.9, 0–2450

EBC (Ratio on, auto range): 0–2450 auto decimal

EBC (Ratio off): 0–9.8

Absorbance (manual range): 0–0.999, 0–2.00

Absorbance (auto range): 0–2.00

Transmittance (%): 1.0–100

Accuracy1, 2, 3FNU4: ±2% of reading plus 0.01 FNU from

0–1000 FNU

FAU: ±10% of reading from 20–10,000 NTU

NTU4: ±2% of reading plus 0.01 NTU from

0–1000 NTU, ±5% of reading from 1000–4000 NTU,

±10% of reading from 4000–10,000 NTU

Absorbance: ±0.005 Abs from 0–1 Abs at 860 nm

Transmittance: 0.12% T from 10–100% T at 860 nm

Resolution Turbidity: 0.001 FNU/NTU/EBC

Absorbance: 0.001 Abs

Transmittance: 0.1% T

Repeatability ±1% of reading or 0.01 FNU, whichever is greater

(under reference conditions)

Response time Signal averaging off: 6.8 seconds

Signal averaging on: 14 seconds (when

10 measurements are used to calculate the average)

English 3

Specification Details

Stabilization time Immediately

Reading modes Manual or auto range, signal averaging on and

adjustable or off, Ratio on or off

Power requirement 115–230 VAC, 50/60 Hz (automatic power selection)

28 W maximum

Pollution

degree/installation

category

2; II

Protection Class 1

Operating conditions Temperature: 0 to 40 °C (32 to 104 °F)

Relative humidity: 0–90% at 25 °C, 0–75% at 40 °C,

noncondensing

Altitude: 2000 m (6560 ft) maximum

Indoor use only

Storage conditions –40 to 60 °C (–40 to 140 °F), instrument only

Printer Built-in (thermal, 58-mm, up to 28 column)

Interface RS232C serial interface by way of DB9 subminiature

D-shell connector for data output to computer or

printer, and data input (command). No handshaking.

Air purge Dry nitrogen or instrument grade air (ANSI MC 11.1,

1975)

0.1 scfm at 69 kPa (10 psig); 138 kPa (20 psig)

maximum

Hose barb connection for 1/8-inch tubing

Sample cells Round cells 95 x 25 mm (3.74 x 1 in.) borosilicate glass

with rubber-lined screw caps

Note: Smaller sample cells (less than 25 mm) can be used

when a cell adapter is used.

Sample requirements 25 mm sample cell: 20 mL minimum

0 to 95 °C (32 to 203 °F)

Enclosure High-impact polycarbonate plastic

Specification Details

Dimensions 30.5 x 40 x 15.6 cm (12.0 x 15.7 x 6.1 in.)

Weight 3.8 kg (8.5 lb)

Certification CE, cETLus

1Turbidity specifications identified using recently prepared formazin standard

and matched 25-mm sample cells.

2Reference conditions: 23 ± 2 °C, 50% ± 10% RH noncondensing,

115/230 VAC, 50/60 Hz

3Intermittent electromagnetic radiation of 3 volts/meter or greater may cause

slight accuracy shifts.

4FNU is equivalent to NTU in the Ratio off mode.

General information

In no event will the manufacturer be liable for direct, indirect, special,

incidental or consequential damages resulting from any defect or

omission in this manual. The manufacturer reserves the right to make

changes in this manual and the products it describes at any time, without

notice or obligation. Revised editions are found on the manufacturer’s

website.

Additional information

Additional information is available on the manufacturer's website.

Safety information

NOTICE

The manufacturer is not responsible for any damages due to misapplication or

misuse of this product including, without limitation, direct, incidental and

consequential damages, and disclaims such damages to the full extent permitted

under applicable law. The user is solely responsible to identify critical application

risks and install appropriate mechanisms to protect processes during a possible

equipment malfunction.

Please read this entire manual before unpacking, setting up or operating

this equipment. Pay attention to all danger and caution statements.

Failure to do so could result in serious injury to the operator or damage

to the equipment.

4 English

Make sure that the protection provided by this equipment is not impaired.

Do not use or install this equipment in any manner other than that

specified in this manual.

Use of hazard information

DANGER

Indicates a potentially or imminently hazardous situation which, if not avoided, will

result in death or serious injury.

W A R N I N G

Indicates a potentially or imminently hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation that may result in minor or moderate

injury.

NOTICE

Indicates a situation which, if not avoided, may cause damage to the instrument.

Information that requires special emphasis.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or

damage to the instrument could occur if not observed. A symbol, if noted

on the instrument, will be included with a danger or caution statement in

the manual.

This symbol, if noted on the instrument, references the instruction

manual for operation and/or safety information.

Electrical equipment marked with this symbol may not be disposed of

in European public disposal systems after 12 August of 2005. In

conformity with European local and national regulations (EU Directive

2002/96/EC), European electrical equipment users must now return

old or end-of-life equipment to the Producer for disposal at no charge

to the user.

Note: For return for recycling, please contact the equipment producer or supplier

for instructions on how to return end-of-life equipment, producer-supplied

electrical accessories, and all auxiliary items for proper disposal.

Certification

Canadian Radio Interference-Causing Equipment Regulation,

IECS-003, Class A:

Supporting test records reside with the manufacturer.

This Class A digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numèrique de la classe A respecte toutes les exigences du

Rëglement sur le matériel brouilleur du Canada.

FCC Part 15, Class "A" Limits

Supporting test records reside with the manufacturer. The device

complies with Part 15 of the FCC Rules. Operation is subject to the

following conditions:

1. The equipment may not cause harmful interference.

2. The equipment must accept any interference received, including

interference that may cause undesired operation.

Changes or modifications to this equipment not expressly approved by

the party responsible for compliance could void the user's authority to

operate the equipment. This equipment has been tested and found to

comply with the limits for a Class A digital device, pursuant to Part 15 of

the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in

English 5

accordance with the instruction manual, may cause harmful interference

to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference, in which case the user will be

required to correct the interference at their expense. The following

techniques can be used to reduce interference problems:

1. Disconnect the equipment from its power source to verify that it is or

is not the source of the interference.

2. If the equipment is connected to the same outlet as the device

experiencing interference, connect the equipment to a different

outlet.

3. Move the equipment away from the device receiving the interference.

4. Reposition the receiving antenna for the device receiving the

interference.

5. Try combinations of the above.

Product overview

The 2100AN IS laboratory turbidimeter measures turbidity in FNUs

(Formazin nephelometric units), NTUs (nephelometric turbidity units) and

EBCs (European Brewing Convention units). NTUs and EBCs are

calculated using the conversion factors of 1.0 NTU per 1.0 FNU and

0.245 EBCs per 1.0 FNU. The 2100AN IS turbidimeter also measures

attenuation (FAU), absorbance and transmittance.

In addition, two user-defined measurement units can be specified. The

application specific mode of operation uses the nephelometric optical

system and the NTU measurement mode.

The turbidimeter has a built-in printer and an RS232 output for

connection to a printer, data logger or computer and a recorder output.

The turbidimeter contains a real-time clock with battery. The clock

provides a time-date stamp on all data transmitted to the built-in printer

or to external devices by way of the RS232 interface (i.e., measurements

and calibration records).

Figure 1 Front overview

1 Mode display: shows the calibration

standard number, setup number or

sample number

5 Cover for the sample cell

compartment

2 Keypad 6 Printer cover

3 Sample cell holder 7 Eight-digit LED display

4 Light shield

6 English

Figure 2 Back overview

1 Power cord connector 5 Air purge fitting

2 Fuse holder 6 Recorder output jack for a chart

recorder (0 to 1 V output)

3 Power switch 7 Remote cable jack for flow valve

module connection to the automatic

flow cell (low pressure)

4 DB9 connector for RS232 cable

Product components

Refer to Figure 3 to make sure that all components have been received.

If any of these items are missing or damaged, contact the manufacturer

or a sales representative immediately.

Figure 3 Instrument components

1 2100AN IS turbidimeter 6 Gelex® secondary turbidity

standardization kit1

2 Oiling cloth 7 Dust cover

3 Six 1" sample cells (30 mL) with

caps

8 Printer paper roll (2x)2

4 Silicone oil 9 Power cord

5 StablCal® Calibration kit

1Supplied with 4790100 only.

2Do not remove the plastic wrapper from the paper rolls until the paper is

installed.

Installation

DANGER

Multiple hazards. Only qualified personnel must conduct the tasks

described in this section of the document.

English 7

Put paper in the printer

NOTICE

Use only the provided thermal paper. Use of other thermal paper may cause poor

print quality and decrease the life of the print-head.

Notes:

• Do not rub the thermal paper with a hard object.

• Do not use chemical paste on thermal paper.

• A red line on the edge of the thermal paper shows when the paper

supply is low.

1. Cut the end of the paper with scissors to make an arrow shape.

2. Open the printer cover.

3. Put the point of the thermal paper in the paper entrance slot.

4. Push the paper through until the point of the paper comes out the

exit slot.

5. Pull the paper out of the exit slot until the full width of the paper is

past the exit slot.

6. Put the paper roll in the printer.

7. Put the thermal paper through the slot in the printer cover, then close

the printer cover.

User interface

Figure 4 Keypad

1 ENTER key 7 FLOW key

2 EDIT (arrow) keys 8 SIGNAL AVG key

3 SAMPLE key 9 PRINT key

4 RANGE key 10 LINE FEED key

5 UNITS/Exit key 11 SETUP key

6 RATIO key 12 CAL/Zero key

Table 1 Key descriptions

Key Description

Enters the value on the display. Starts the measurement of a

calibration standard. Clears data from the buffer.

Changes the numbers and/or letters on the display. Steps through

the calibration standards. The right arrow key moves the cursor to

the previous or next digit.

8 English

Table 1 Key descriptions (continued)

Key Description

Starts the changing of the sample number shown on the mode

display.

Selects automatic or manual ranging.

Selects the unit of measure. Exits Calibration or Setup mode

without saving changes.

Turns Ratio on or off.

Turns on or off the Flow mode of operation. Used only with the

automated flow cell.

Turns signal averaging on or off.

Sends the data that is on the display to a printer or computer.

Sends a calibration data report to a printer or computer when in

Calibration mode. Sends diagnostic results to a printer or computer

if held down when the instrument is turned on. Provides a print of

the setup commands when in Setup mode. Turns the print interval

feature on or off if the instrument has been configured with a printer

interval.

Moves the printer paper forward one line.

Turns on Setup mode and starts the selection of the setup number

on the mode display.

Starts a calibration when in FNU, FAU, NTU or EBC mode. Starts

analytical zeroing when in %T or Abs mode.

Figure 5 Indicator lights

1 Lamp icon light 7 PRINT light

2 "CAL?" light 8 SIGNAL AVG light

3 "Manual" light 9 CAL/Zero light

4 "Auto" light 10 SETUP light

5 RATIO light 11 SAMPLE light

6 FLOW light

English 9

Table 2 Light descriptions

Light Description

Illuminated when the instrument light source is on.

Flashes when there is not sufficient light for measurement.

CAL? "CAL?" is shown during a calibration if the calibration data is not

within the acceptable range.

Flashes when the instrument should be calibrated.

Note: The CAL? light applies when a 25-mm sample cell is used. Ignore the

CAL? light if illuminated during calibration when a smaller sample cell is used.

Push UNITS/Exit to start measurements.

Manual "MANUAL" is shown above the Range Mode label when the

instrument is in manual ranging mode.

Auto "AUTO" is shown below the Range Mode label when the instrument is

in auto ranging mode.

RATIO Illuminated when Ratio is on.

FLOW Illuminated when the Flow mode of operation is selected.

Flashes when the flow cycle is done.

PRINT Illuminated when the printer interval feature is selected.

Flashes when a print interval has been selected but is not active.

SIGNAL

AVG

Illuminated when signal averaging is on.

CAL

Zero

Illuminated when Calibration or Zeroing mode is selected.

SETUP Illuminated when Setup mode is selected.

SAMPLE Illuminated when Sample mode is selected.

Startup

Turn the instrument on

CAUTION

Infrared Light Hazard. The infrared light produced by this instrument can cause

eye injury. The infrared light source in this instrument only receives power when

the sample cell cover is closed.

1. Put the instrument on a stable, level surface that is free of vibration.

Do not put in direct sunlight.

2. Make sure that there is air circulation around the instrument. Keep

the back and area below the instrument free of material that could

decrease air flow through the vents.

3. Connect the power cord to the power plug on the back of the

instrument.

4. Connect the power cord to a power socket with ground contact.

5. Push the power switch on the back of the instrument to turn the

instrument on.

Turn the keypad sound off (optional)

By default, the instrument makes an audible sound when a key is

pushed. To turn the keypad sound off:

1. Push SETUP. The SETUP light turns on.

2. Use the arrow keys to select 00.

3. Push ENTER.

4. Use the arrow keys to select the sound option:

Option Description

BEEP ON An audible sound is made when a key is pushed.

BEEP OFF No sound is made when a key is pushed.

5. Push ENTER.

6. Push SETUP.

10 English

Andere Handbücher für 2100AN IS

Inhaltsverzeichnis

Sprachen:

Andere Hach Laborausrüstung Handbücher

Hach

Hach BODTrak II Kurzanleitung

Hach

Hach Lachat BD40HT Bedienungsanleitung

Hach

Hach sensION+ pH3 Bedienungsanleitung

Hach

Hach DR 6000 Kurzanleitung

Hach

Hach 900 MAX Bedienungsanleitung

Hach

Hach HQ440d Bedienungsanleitung

Hach

Hach AS1000 Bedienungsanleitung

Hach

Hach TenSette 19700-01 Bedienungsanleitung

Hach

Hach Digesdahl 23130-20 Bedienungsanleitung

Hach

Hach DR 5000 Bedienungsanleitung

Hach

Hach AS950 AWRS Bedienungsanleitung

Hach

Hach TitraStir 19400-00 Bedienungsanleitung

Hach

Hach POCKET TURBIDIMETER Bedienungsanleitung

Hach

Hach LQV157.99.50001 Bedienungsanleitung

Hach

Hach SIGMA 900 Bedienungsanleitung

Hach

Hach DRB 200 Bedienungsanleitung

Hach

Hach Lange 2100AN Bedienungsanleitung

Hach

Hach DR 3900 Kurzanleitung

Hach

Hach PHOSPHAX sc LR Bedienungsanleitung

Hach

Hach DRB 200 Bedienungsanleitung

Hach

Hach TitraLab KF1000 Series Kurzanleitung

Hach

Hach LOC 100 Bedienungsanleitung

Hach

Hach GANIMEDE P Bedienungsanleitung

Hach

Hach sensION+ MM374 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung