Hach Lachat BD40HT Bedienungsanleitung

DOC022.97.80306

Lachat BD40HT

06/2012, Edition 1

User Manual

Manuel d'utilisation

Manual del usuario

Manual do Usuário

用户手册

取扱説明書

사용 설명서

English..............................................................................................................................3

Français.........................................................................................................................20

Español..........................................................................................................................38

Português......................................................................................................................56

中文.................................................................................................................................73

日本語.............................................................................................................................89

한글...............................................................................................................................106

Table of contents

Specifications on page 3 Operation on page 11

General information on page 3 Maintenance on page 16

Installation on page 7 Troubleshooting on page 18

User interface on page 9 Replacement parts and accessories on page 19

Startup on page 11

Specifications

Specifications are subject to change without notice.

Specification Details

Digestion block

Dimensions (W x D x H) 43 x 44 x 69 cm (17 x 17.5 x 27 in.)

Weight 20.9 kg (46.1 lb)

Power requirements 230 V ±5%, 3400 W, 50/60 Hz

Operating temperature Maximum 450 °C (842 °F)

Capacity 40 samples

Sample tube 115 mL capacity

Controller

Dimensions (W x D x H) 25 x 19 x 17 cm (9.8 x 7.5 x 6.8 in.)

Weight 2.2 kg (4.9 lb)

Power requirements 230 V ±10%, 50/60 Hz

Operating temperature Maximum 85 °C (185 °F)

Environmental specifications, controller and digestion block

Installation category II

Pollution degree 2

Altitude Up to 2000 m

Relative humidity 30% to 80%

Storage temperature –5 to 40 °C (23 to 104 °F)

Warranty 1 year from date of purchase

General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential

damages resulting from any defect or omission in this manual. The manufacturer reserves the right to

make changes in this manual and the products it describes at any time, without notice or obligation.

Revised editions are found on the manufacturer’s website.

English 3

Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,

without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical application risks and install

appropriate mechanisms to protect processes during a possible equipment malfunction.

Please read this entire manual before unpacking, setting up or operating this equipment. Pay

attention to all danger and caution statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired. Do not use or install this

equipment in any manner other than that specified in this manual.

Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special

emphasis.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the instrument

could occur if not observed. A symbol on the instrument is referenced in the manual with a

precautionary statement.

This is the safety alert symbol. Obey all safety messages that follow this symbol to avoid potential

injury. If on the instrument, refer to the instruction manual for operation or safety information.

This symbol indicates that a risk of electrical shock and/or electrocution exists.

This symbol identifies the presence of a strong corrosive or other hazardous substance and a risk of

chemical harm. Only individuals qualified and trained to work with chemicals should handle chemicals

or perform maintenance on chemical delivery systems associated with the equipment.

This symbol indicates the need for protective eye wear.

This symbol indicates that the marked item can be hot and should not be touched without care.

4 English

This symbol indicates that the object is heavy.

This symbol indicates the presence of toxic gas. Use of a fume hood is required.

Electrical equipment marked with this symbol may not be disposed of in European public disposal

systems after 12 August of 2005. In conformity with European local and national regulations (EU

Directive 2002/96/EC), European electrical equipment users must now return old or end-of-life

equipment to the Producer for disposal at no charge to the user.

Note: For return for recycling, please contact the equipment producer or supplier for instructions on how to return end-

of-life equipment, producer-supplied electrical accessories, and all auxiliary items for proper disposal.

Certification

Canadian Radio Interference-Causing Equipment Regulation, IECS-003, Class A:

Supporting test records reside with the manufacturer.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numèrique de la classe A respecte toutes les exigences du Rëglement sur le matériel

brouilleur du Canada.

FCC Part 15, Class "A" Limits

Supporting test records reside with the manufacturer. The device complies with Part 15 of the FCC

Rules. Operation is subject to the following conditions:

1. The equipment may not cause harmful interference.

2. The equipment must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications to this equipment not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment. This equipment has been tested

and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to

correct the interference at their expense. The following techniques can be used to reduce

interference problems:

1. Disconnect the equipment from its power source to verify that it is or is not the source of the

interference.

2. If the equipment is connected to the same outlet as the device experiencing interference, connect

the equipment to a different outlet.

3. Move the equipment away from the device receiving the interference.

4. Reposition the receiving antenna for the device receiving the interference.

5. Try combinations of the above.

Product overview

WARNING

Gas inhalation hazard. Operate the instrument in a fume hood to prevent exposure to hazardous gas.

English 5

WARNING

Burn hazard. The digestion block gets extremely hot. Do not touch.

The BD40HT is a high-temperature block digestion system. A color touchscreen controller gives

power to the digestion block (Figure 1). The controller holds 12 test methods. The test methods

control test times and temperatures and can be modified as necessary.

The digestion block holds 40 digestion tubes (Figure 2). Samples can be heated to 450 °C.

Figure 1 Touchscreen controller

1 Stylus for touchscreen 5 Power cable connection to digestion block

2 Color touchscreen interface 6 Power cord connector

3 Dongle port (COM 2) 7 Power switch

4 Dongle

6 English

Figure 2 Digestion block

1 Graphite block (SiC coated) 5 Cold finger (40x)

2 Reaction tube and cooling rack 6 Temperature calibration connection

3 Heat deflector shield (2x) 7 Cable, controller to digestion block

4 Digestion tube (40x)

Installation

D A N G E R

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

Mechanical installation

Assemble the digestion block

WARNING

Personal injury hazard. Instruments or components are heavy. Use assistance to install or move.

Figure 3 shows the assembly of the digestion block. Make sure to hold the digestion block by the

base to move it.

English 7

Figure 3 Digestion block assembly

Install the heat deflectors

The rack has two heat deflectors that can be installed as necessary. Use the heat deflectors to

improve evaporation. Figure 4 shows how to install the heat deflectors.

8 English

Figure 4 Heat deflector installation

Electrical installation

Power connections

D A N G E R

Electrocution hazard. If this equipment is used outdoors or in potentially wet locations, a Ground Fault

Circuit Interrupt (GFCI/GFI) device must be used for connecting the equipment to its main power

source.

Refer to Figure 5 to connect the digestion block and controller to power.

Figure 5 Power connections

1 Power cord, 230 V, 15 A with C19 connector

User interface

Figure 6 and Table 1 show the main functions of the Run screen interface.

English 9

Figure 6 Run screen

1 Current temperature display 5 Alarm

2 Menu tab 6 Utilities tab

3 Edit tab 7 Graph of the current temperature and time

4 Run tab 8 Current time (time elapsed) display

Table 1 Run screen description

Function Description

Current temperature display Numerical display of the current digestion block temperature

Menu tab List of the test methods in the controller

Edit tab Change the parameters of a method and enter new methods

Run tab Start, stop and monitor the progress of a method

Alarm indicator The audio alarm is active when the green light shows. The alarm is

deactivated when a gray light shows.

Utilities tab Select the language or calibrate the touchscreen

Graph of the current temperature

and time

Graphical display of the progress of the method. The cursor shows the

progress of the method.

Current time display Numerical display of the amount of time the method has been in operation

Figure 7 and Table 2 show the functions of the Edit screen interface. Select a field to enter a value.

10 English

Inhaltsverzeichnis

Sprachen:

Andere Hach Laborausrüstung Handbücher

Hach

Hach SIGMA 900 Bedienungsanleitung

Hach

Hach ORBISPHERE 29122 Bedienungsanleitung

Hach

Hach sensIONTM+ pH31 Bedienungsanleitung

Hach

Hach MET ONE 6003 Bedienungsanleitung

Hach

Hach TU5200 Bedienungsanleitung

Hach

Hach BODTrak Bedienungsanleitung

Hach

Hach Intellical MTC30101 Bedienungsanleitung

Hach

Hach BOD Direct plus Kurzanleitung

Hach

Hach TitraStir 19400-00 Bedienungsanleitung

Hach

Hach sensION+ EC7 Bedienungsanleitung

Hach

Hach SIP 10 Bedienungsanleitung

Hach

Hach DRB 200 Bedienungsanleitung

Hach

Hach 2100AN IS Kurzanleitung

Hach

Hach LOC 100 Bedienungsanleitung

Hach

Hach HQ440d Bedienungsanleitung

Hach

Hach LQV157.99.50001 Bedienungsanleitung

Hach

Hach ISENH4181 Bedienungsanleitung

Hach

Hach TitraLab KF1000 Series Kurzanleitung

Hach

Hach MET ONE 3400 Series Bedienungsanleitung

Hach

Hach MTC10101 Bedienungsanleitung

Hach

Hach AS950 AWRS Bedienungsanleitung

Hach

Hach TenSette 19700-01 Bedienungsanleitung

Hach

Hach LT 200 Bedienungsanleitung

Hach

Hach TitraLab Kurzanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung