Honeywell VERSAFLOW VORTEX 200 Bedienungsanleitung
Quick Start
For initial set up, we strongly recommend the use of the relevant manuals in addition!
07/2019 - 4007779101 - 34-VF-25-76 iss.1 GLO July 2019 US 1
VERSAFLOW VORTEX 200
Vortex flowmeter
Installation, assembly, start-up and maintenance may only be performed by appropriately
trained personnel.
For use in hazardous areas, special codes and regulations are applicable which are supplied in
a separate document that describes all hazardous area relevant information.
The responsibility as to the suitability, intended use and corrosion resistance of the used
materials against the measured fluid of this device rests solely with the operator.
For complete documentation (manuals, supplementary manuals, data sheets and certificates)
please refer to www.honeywellprocess.com.
1 Installation
Liquids
Steam & gases
Sandwich design – centering rings
Centering rings
(part of scope of supply)
Transport
Pipelines with control valve
Remote: wall mounting of the field housing Remote: pipe mounting of the field housing
5 DN
07/2019 - 4007779101 - 34-VF-25-76 iss.1 GLO July 2019 US 2
2 Electrical connection
Minimum inlet section
15 DN
50 DN
20 DN
20 DN
40 DN
30 DN
> 5 DN
5 DN
5 DN
Minimum outlet section Heat insulation for Tmedium > +160°C / +320°F
1 1
2
3
1 Marking of max. height of the insulation
2 Max. thickness of the insulation up to the bend of the pressure pipe
3 Insulation
1
2
3
4
5
6
7
8
1 Open the housing cover of the electrical terminal compartment using the key
2 Signal converter supply and 4...20 mA loop
3 4...20 mA current input, - external transmitter, optional
4 Terminal M1 binary (high current)
5 Terminal M3 binary (NAMUR)
6 Terminal M2/4 binary, common minus connection
7 Ground terminal in housing
8 Ground terminal on connection piece between flow sensor and signal converter
Connecting the signal converter
Sunshade
07/2019 - 4007779101 - 34-VF-25-76 iss.1 GLO July 2019 US 3
Terminal Strand colour
rd red
bu blue
bk black
gr grey
ye yellow
gn green
gnye Shielding
Current output
Current input
Pulse output / frequency output
Limit switch output
Power supply for the signal
converter
Current input (I1+ and I2-) of an external
temperature or pressure transmitter
Connect current loop 4..20 mA to
terminals C1+ and C2-
Connection NAMUR:
M2/4 (common); M3 (open collector)
Connection transistor output:
M2/4 (common); M1 (open collector)
The maximum frequency of both pulse
output and frequency output is 1000 Hz
The connection is made between terminal
M2/4 Common (-) and M1 for Hi Current
(+) or M3 NAMUR (+)
Status output
The connection is made between terminal M2/4 Common (-) and M1 for Hi Current (+) or
M3 NAMUR (+)
Connection of remote version
1 Connection terminal flow sensor
2 Connection terminal signal converter
3 Connection shielding flow sensor
4 Shielding (drain wire and overall shield)
5 Connection shielding signal converter
6 Heat shrink tubing
7 Shielding
1 2
3
4
3
4
5
5
6
6
7 7
Grounding of compact version
1 Ground terminal in housing
2 Ground terminal on connection piece between
flow sensor and signal converter
1
2
Grounding of remote version
1 Ground terminal on flow sensor
2 Ground terminal on signal converter housing
2
1
07/2019 - 4007779101 - 34-VF-25-76 iss.1 GLO July 2019 US 4
3 Quick Setup
Meas. Menu A Submenus
>
>
>
A Quick
Setup
A1 Language
A2 Contrast
A3 Login
A4 Tag
A5 Long Tag
A6 Message View
A7 Fluid
A8 Medium
A9 Units
A9.1 Volume Flow A9.2 Cst. Vol. Flow
A9.3 Norm. Vol. Flow A9.4 Cst. N.Vol.Flow
A9.5 Mass Flow A9.6 Cst. Mass Flow
A9.7 Power A9.8 Cst. Power
A9.9 Volume A9.10 Cst. Volume
A9.11 Norm. Volume A9.12 Cst. Norm. Volume
A9.13 Mass A9.14 Cst. Mass
A9.15 Energy A9.16 Cst. Energy
A9.17 Pressure A9.18 Cst. Pressure
A9.19 Temperature A9.20 Cst. Temp.
A9.21 Density A9.22 Cst. Density
A10 Meter Type
A11 Application Assistant
A11.1 Liquids
A11.2 Saturated Steam
A11.3 Superheated Steam
A11.4 Heat Measurement
A11.5 Gas
A11.6 FAD
A12 Cluster Checks Cluster 1...12
Access level Def ault p a ssword Permis sions
User 0000
(any unassigned password)
View device information
Configure the display (C5), including changing the display
language and the content of the measurement pages
Operator 0009 All rights of "User" access level
Configure binary output (C2.2)
Configure all HART® communication options (C3) with the
exception of "C3.1.1 Current Loop Mode"
Change "Operator" password (C6.2.2) – note that the new
password must have three leading zeroes ("000")
Activate a different meter type
Expert 0058 All configuration rights, especially process setup (C1) and
current output (C2.1)
Change "Expert" password (C6.2.2) – note that the new
password must have two leading zeroes ("00")
Contact
Honeywell Process Solutions
1250 W Sam Houston Pkwy S
Houston, TX 77042
www.honeywellprocess.com
© Honeywell International Inc.
Subject to change without notice.
Operation with open front cover Operation with
closed
front cover
(with bar magnet)
Andere Handbücher für VERSAFLOW VORTEX 200
1
Inhaltsverzeichnis
Andere Honeywell Messgerät Handbücher
Honeywell
Honeywell MagneW 3000 Plus Benutzerhandbuch
Honeywell
Honeywell Elster EK280 Gebrauchsanweisung
Honeywell
Honeywell W8600B Bedienungsanleitung
Honeywell
Honeywell 7866 Bedienungsanleitung
Honeywell
Honeywell 6108 Anleitung zur Verwendung
Honeywell
Honeywell HG4930 Bedienungsanleitung
Honeywell
Honeywell E-Mon Class 3200 Bedienungsanleitung
Honeywell
Honeywell RMA 3000 Bedienungsanleitung
Honeywell
Honeywell Enraf 977 Bedienungsanleitung
Honeywell
Honeywell Touchpoint Plus Bedienungsanleitung
Honeywell
Honeywell CM4 Bedienungsanleitung
Honeywell
Honeywell Q209E Modutrol IV Bedienungsanleitung
Honeywell
Honeywell QA 10 DN 25 G I Bedienungsanleitung
Honeywell
Honeywell SmartLine RMA800 Bedienungsanleitung
Honeywell
Honeywell UDA2182 Bedienungsanleitung
Honeywell
Honeywell FlexLine SmartServo 954 Bedienungsanleitung
Honeywell
Honeywell Vertex M Bedienungsanleitung
Honeywell
Honeywell MiniRAE 3000+ Bedienungsanleitung
Honeywell
Honeywell Q4000 Bedienungsanleitung
Honeywell
Honeywell SEARCHLINE EXCEL PLUS Bedienungsanleitung
