HP Model 748 - VME Workstation Bedienungsanleitung

Installing the A4505A PCI Module Upgrade

HP Part No. A4500-90603

Edition E0297

Printed in U.S.A.

Hewlett-Packard Co. 1997

Printing History

First Printing: February 1997

UNIX is a registered trademark in the United States and other countries,

licensed exclusively through X/Open Company Limited.

NOTICE

The information contained in this document is subject to change without

notice.

HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND WITH

REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FIT-

NESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be lia-

ble for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copy-

reproduced or translated to another language without the prior written con-

sent of Hewlett-Packard Company.

RESTRICTED RIGHTS LEGEND. Use, duplication, or disclosure by gov-

ernment is subject to restrictions as set forth in subdivision (c) (1) (ii) of the

Rights in Technical Data and Computer Software Clause at DFARS

252.227.7013. Hewlett-Packard Co., 3000 Hanover St., Palo Alto, CA

94304.

10 9 8 7 6 5 4 3 2 1

Kit Contents

Make sure that you have kit A4505A and that it contains the following

items:

• PCI tray assembly

• Boot ROM for Model 743 VMEbus board computer

• IC Removal Tool

• Anti-static Strap (Disposable)

Tools Required

You’ll need the following items to install the PCI Module:

• Medium flat-tipped screwdriver.

• Static-free work area.

Prerequisites

Your system must be running version 10.20 or later of the HP-UX operating

system.

The PCI module upgrade does not support HIL devices. You must remove

any devices connected to the HIL interface connector on the EISA tray.

NOTICE: Before removing your HIL keyboard, use the SAM utility to make sure that

the P/S2 driver is conﬁgured in the HP-UX kernel. Refer to the manual

HP-UX System Administration Tasks (B2355-90079) for information on

conﬁguring the HP-UX kernel.

Procedure

If you need keyboard and mouse support, you need a Hewlett-Packard P/S2

compatible keyboard and mouse to connect to the P/S2 connectors on the

VMEbus board computer.

Procedure

1Stop any application programs, then shut down your workstation.

2Turn the workstation off, and unplug the power cord(s).

WARNING: To avoid electrical shock, make sure you unplug the power cable from the wall

outlet and the system unit before proceeding any further.

CAUTION: The internal components of your workstation are susceptible to mechanical

and electrostatic shock. To prevent such damage from occurring, observe

the following precautions during the installation procedure.

• Stand on a static-free mat

• Wear a static-grounding wrist strap to ensure that any accumulated

electrostatic charge discharges from your body to ground. Attach the

static-grounding wrist strap by following the instructions on the pack-

age that contains the strap. Be sure to attach one end of the strap to the

system chassis.

• Handle workstation and upgrade kit components carefully to prevent

damage from mechanical shock.

3Using a flat-tipped screwdriver, unscrew the captive screws inside the

EISA module handles five to seven turns (until each screw pops out).

4Grasp the EISA module handles and pull the EISA module out of the

chassis, as shown in Figure 1.

Procedure

Figure 1 Removing the EISA Module

5Note that the slots are numbered on the front of the tray from 1 to 4.

NOTICES: This PCI tray only supports option cards with +5 volt bus signalling.

If your workstation application requires several accessory cards and mass

storage devices, power budgeting may be required. This ensures the power

needed for these internal devices does not exceed the power available in the

system.

The PCI tray provides power for option cards from both a +3.3 Vdc source

and a +5 Vdc source. Cards may use either or both power sources, up to

25W per slot. However, the +3.3 V dc source is limited to 39.8 W

combined for slots 1 and 2, and 39.8 W combined for slots 3 and 4. For

example, if the card in slot 1 draws 25 W at +3.3 V dc, only 14.8 W at +3.3

V dc is available to a card in slot 2. The limits of + 5 Vdc is 25 W per slot.

If you upgrade your system, adding more: RAM cards, mass storage

devices, or VME, or PCI accessory cards, you must recompute the power

budget to ensure the new conﬁguration is within the system’s capability.

Refer to your system’s documentation for other power limits.

Screws

Slot 1

Slot 2

Slot 3

Slot 4

Procedure

Cards for slots 1 and 2 are installed component side up; cards for slots 3

and 4 are installed component side down.

Loosen the card retainer captive screw (see Figure 2) for the appropriate

slot, and then remove the card retainer, as shown in Figure 3.

Figure 2 Card Retainer Captive Screw

Card Retainer Captive Screw

Procedure

Figure 3 Removing the Card Retainer and Slot Cover Plate

6Remove the slot cover plate by pulling it out of the PCI module, as shown

in Figure 3.

7Refer to your PCI card installation manual, and set any configuration

switches or jumpers that may be required for your application.

Slot Cover Plate

Card Retainer

Procedure

8Install the PCI card in the slot, as shown in Figure 4. Make sure its con-

nector is completely seated in the PCI backplane.

Figure 4 Installing a PCI Option Card

9Replace the PCI card retainer, and then tighten its screw.

PCI Option Card

Procedure

10 Slide the PCI module into the VMEbus chassis, as shown in Figure 5, and

tighten its handle screws.

Figure 5 Installing the PCI Module into the VMEbus Chassis

Procedure

11 IfyoursystemhasaModel743VMEbusboardcomputerinstalled,youmayneed

to update its firmware to make use of the PCI module. (Model 744 board com-

puters do not require a firmware upgrade.)

A new Boot ROM is shipped with the PCI Module upgrade kit. To deter-

mine if the Boot ROM in your system needs to be replaced, you need to

determine the revision number, which can be done in two ways: use the

Boot Console Handler (BCH) interface as described in the Model 743

Owner’s Guide, or you can examine the label on the Boot ROM - a revi-

sion number is printed on the label. If the revision number on the Boot

ROM installed on the Model 743 is a lower number than the one included

in this kit, you should replace that Boot ROM with the one in this kit. If

the revision number on the Boot ROOM installed on the Model 743 is

equal to or greater than the one included in this kit, DO NOT replace the

Boot ROM on the model 743.

aLoosen the board computer’s four captive screws.

bPush the ejector handles to the outside of the board and remove the board

computer from the Model 748 card cage.

cRemove any option cards, if installed. Refer to the Model 743 Owner’s Guide

for specific instructions for you option card.

NOTE: Before removing the Boot ROM, note its orientation. The replacement Boot

ROM must be installed in the same orientation.

dRemove the Boot ROM from its socket using the IC removal tool.

eAlign the new Boot ROM in its socket and carefully press it into the socket.

Figure 6 Model 743 Boot ROM Location

Boot R

(

U54

)

Andere Handbücher für Model 748 - VME Workstation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP PCI-Karte Handbücher

HP 435508-B21 Gebrauchsanweisung

HP PCIe 2-Port 10GbE Bedienungsanleitung

HP NC380T Gebrauchsanweisung

HP Vectra VEC 7 Bedienungsanleitung

HP Vectra VEi 7 Bedienungsanleitung

HP NC150T Bedienungsanleitung

HP 4X - DDR InfiniBand Mezzanine HCA Merkblatt

HP Edgeline EL1000 Bedienungsanleitung

HP Xw4600 - Workstation - 2 GB RAM Bedienungsanleitung

HP Xw460c - ProLiant - Blade Workstation Bedienungsanleitung

HP Vectra VL6 7 Bedienungsanleitung

HP Thunderbolt 3 Bedienungsanleitung

HP 673642-B21 Bedienungsanleitung

HP Compaq Pro 6305 Bedienungsanleitung

HP IEEE-1394b Bedienungsanleitung

HP 04H8095 Bedienungsanleitung

HP VL600 - Vectra - 128 MB RAM Bedienungsanleitung

HP NC375T Bedienungsanleitung

HP StorageWorks Q2300 Bedienungsanleitung

HP FC HBAs Installationsanleitung

HP Vectra VL6 6 Bedienungsanleitung

HP NC570C Bedienungsanleitung

HP AB465A Bedienungsanleitung

HP Vectra VL410 Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung