HP IEEE-1394b Bedienungsanleitung

IEEE-1394b PCI Express Card

installation

Introduction

This document describes how to install an IEEE-1394b PCI Express (PCIe) card in HP Z series

workstations.

Kit contents

●IEEE-1394b PCIe card

●External 1394b cable

●SATA power extension cable

●1394b Unibrain drivers CD

●Warranty information

●Installation instructions

Before you begin

To view QuickSpecs and determine the compatibility of this product with your HP workstation, see

http://www.hp.com/go/productbulletin.

ENWW Introduction 1

Warnings and cautions

WARNING! Any surface or area of the equipment marked with this symbol indicates the

presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists.

To reduce the risk of injury from a hot component, enable the surface to cool before touching.

WARNING! Any surface or area of the equipment marked with this symbol indicates the

presence of an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open

any enclosed area marked with this symbol.

WARNING! To reduce the risk of electric shock or damage to your equipment:

— Do not disable the power cord grounding plug. The grounding plug is an important safety feature.

— Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.

— Disconnect power from the equipment by unplugging the power cord from the electrical outlet.

WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes

proper computer setup, posture, health, and work habits for computer users, and provides important

electrical and mechanical safety information. This guide is located at http://www.hp.com/ergo and on

the documentation CD (if one is included with the product).

WARNING! If a product is shipped in packaging marked with this symbol, , the product must

always be lifted by two persons to avoid personal injury due to product weight.

CAUTION: Static electricity can damage the electronic components of the computer. Before

beginning these procedures, be sure you discharge static electricity by briefly touching a grounded

metal object.

CAUTION: To prevent damage to the computer, observe the following Electrostatic Discharge (ESD)

precautions while performing the system parts removal and replacement procedures:

— Work on a static-free mat.

— Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your

body to the ground.

— Create a common ground for the equipment you are working on by connecting the static-free mat,

static strap, and peripheral units to that piece of equipment.

NOTE: HP accessories are for use in HP computer products. They have been extensively tested for

reliability and are manufactured to high quality standards.

2 IEEE-1394b PCI Express Card installation ENWW

Step 1—Preparing for component installation

NOTE: Workstation models vary. All illustrations are examples only.

Download and install updates

1. Check for available system BIOS updates specified for your HP workstation model and operating

system at http://www.hp.com/go/workstationsupport.

2. Install the system BIOS updates, if available.

Accessing the internal components of the computer

1. If you need help preparing the computer for this installation, consult the removal and replacement

procedures in the service guide for your computer at http://www.hp.com/support/manuals.

2. Power down the computer, and then disconnect the power cord.

3. Power down all external devices, and then disconnect them from the computer.

4. Remove the side access panel.

Removing components

1. Some workstations may have card hold-down supports installed. If any card support is present,

remove it for access to the expansion slots and system board connectors.

2. Select an appropriate PCIe expansion slot and remove the slot cover. The IEEE-1394b card may

be installed in any unused PCIe expansion slot.

NOTE: To identify PCIe expansion slots, see the service label on the side access panel.

Figure 1 Removing the expansion slot cover

ENWW Step 1—Preparing for component installation 3

Step 2—Installing the IEEE-1394b card

1. Install the IEEE-1394b card (1) in the selected PCIe expansion slot.

2. Lower the expansion slot retention clamp and close the retention clamp lever (2).

Figure 2 Installing the IEEE-1394b card

Step 3—Configuring the cabling

1. Connect the male end (labeled P1) of the SATA power extension cable to the workstation optical

drive power supply, according to the following workstation series:

●For the HP Z400 workstation, use the connector labeled P8

●For the HP Z600 and Z800 workstations, use the connector labeled P5

2. If the P5 or P8 connectors were used by another optical drive device, connect the center connector

(labeled P2) of the SATA power extension cable to the optical disk drive needing power. Route or

tie excess cable to ensure it does not interfere with system fans.

3. Connect the other end (labeled P3) of the SATA power extension cable to the power connector on

the IEEE-1394b card.

Figure 3 Connecting the SATA power extension cable

4 IEEE-1394b PCI Express Card installation ENWW

4. If the 1394 header is not present on the system board, plug the 1394 I/O cable located on the

side of the workstation chassis into the 1394b card (1).

IMPORTANT: Do not unplug the front I/O connector from the system board.

Figure 4 Connecting the 1394 I/O cable to the 1394b card

Step 4—Reassembling the workstation

1. Reinstall the card support, if applicable.

2. Reinstall the side access panel.

3. Reconnect power to the workstation and all external devices.

4. Restore power to the workstation and all external devices.

Japanese 日本語

This document is available in Japanese. See http://www.hp.com/support/workstation_manuals, then

select your workstation product and select Japanese from the drop down Manual Language

menu.

このドキュメントは日本語版が用意されています。http://www.hp.com/support/

workstation_manuals にアクセスし、ご使用のワークステーション製品を選択し、Manual Language

ドロップダウンメニューから Japanese を選択してください。

ENWW Step 4—Reassembling the workstation 5

Inhaltsverzeichnis

Andere HP PCI-Karte Handbücher

HP 04H8095 Bedienungsanleitung

HP Thunderbolt 3 Bedienungsanleitung

HP NC150T Bedienungsanleitung

HP 4X - DDR InfiniBand Mezzanine HCA Merkblatt

HP AB465A Bedienungsanleitung

HP Vectra VEi 7 Bedienungsanleitung

HP NC375T Bedienungsanleitung

HP A6826A Anleitung zur Verwendung

HP Vectra VEi 7 Bedienungsanleitung

HP VL600 - Vectra - 128 MB RAM Bedienungsanleitung

HP FX 3500 Installationsanleitung

HP StorageWorks Q2300 Bedienungsanleitung

HP Xw460c - ProLiant - Blade Workstation Bedienungsanleitung

HP Vectra VL6 8 Bedienungsanleitung

HP 673642-B21 Bedienungsanleitung

HP NC570C Bedienungsanleitung

HP Compaq Pro 6305 Bedienungsanleitung

HP Vectra VL6 7 Bedienungsanleitung

HP Vectra VE6 8 Bedienungsanleitung

HP Vectra VEC 7 Bedienungsanleitung

HP NC1020 Gebrauchsanweisung

HP A7173A Bedienungsanleitung

HP StorageWorks fca2384 Bedienungsanleitung

HP Model 748 - VME Workstation Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung