ICP DAS USA TM-P3R3 Bedienungsanleitung

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

tM-P3R3

3-channel Isolated Digital Input and 3-

channel Relay Output Module

Quick Start Guide

Product Website:

http://www.icpdas-usa.com/tm_p3r3.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The tM-P3R3 provides 3 channels for digital input and 3 channels for relay output, each

of which features photocouple isolation. All output channels are form A type relays,

while input is based on sink- or souce-type using a wire connecion. All input channels

can be used an 16-bit counters. There are options for configuring power-on and safe

digital output values. 4 kV ESD protection and 3750 VDC intra-module isolation are also

provided.

2. Terminal Assignment

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

•Use 26-12 AWG wire for signal

connections.

•Strip the wire to a length of

7±0.5mm.

•Use a crimp terminal for wiring.

•Avoid high-voltage cables and

power equipment as much as

possible.

•For RS-485 communication, use

insulated and twisted pair 24 AWG

wire, e.g. Belden 9841.

4. Default Settings

Default settings for the tM-P3R3 module are as follows:

。Protocol: Modbus RTU

。Module Address: 01

。DIO Type: Type 40

。Baud Rate: 9600 bps

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. The Modbus RTU communication protocol is the default protocol of the tM series.

The communication Baud Rates for the Modbus RTU protocol can be in the range of

1200 bps to 115200 bps

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Inhaltsverzeichnis

Andere ICP DAS USA Steuereinheit Handbücher

ICP DAS USA

ICP DAS USA GPS-721-MRTU Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD8C Bedienungsanleitung

ICP DAS USA

ICP DAS USA iDaSer-9000 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PET-7261 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7016 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PM-4324 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7069D Bedienungsanleitung

ICP DAS USA

ICP DAS USA HRT-370 Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7016D Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7045 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7060 Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-8014W Bedienungsanleitung

ICP DAS USA

ICP DAS USA GW-7552-M Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7083 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7069 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-7065 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7051D Bedienungsanleitung

ICP DAS USA

ICP DAS USA IR-310-RM Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD4P2C2 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7026 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ZT-2053 Bedienungsanleitung

ICP DAS USA

ICP DAS USA USB-87P1 Bedienungsanleitung

ICP DAS USA

ICP DAS USA 7188EN Installationsanleitung

ICP DAS USA

ICP DAS USA tET-P2A2 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung

ICP DAS USA tM-P3R3 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken