Interlogix MobileView MVC-7100-29-BL Bedienungsanleitung
Mini-Dome Camera Installation Manual 1
Mini-Dome Camera Installation Manual
Content
Introduction 1
Location and Preparation 1
Installation 1
Troubleshooting 4
FCC Compliance 4
Contact information 4
Mounting bracket template 5
Introduction
The MobileView™ Mini-Dome Camera Installation
Manual includes instructions for installation inside a
transit vehicle. Read through these instructions before
installation.
To use this document, you must have the following
minimum qualifications:
A basic knowledge of CCTV systems and
components; and
A basic knowledge of electrical wiring and low-
voltage electrical hookups.
Location and Preparation
The mini-dome camera is designed for interior use only.
Choose a protected location inside the vehicle that will
deliver the desired image.
Before beginning, confirm you have the following parts
required for installation:
MobileView™ Mini-Dome Camera
Three (3) machine screws with red nylon washers
Three (3) flat-head sheet-metal screws with black
nylon washers (optional)
Hex wrench
MobileView™ Part Numbers:
MVC-7100-29-BL Mini-dome, 600TVL, 2.9mm lens, black, No IR
MVC-7100-29-BLI Mini-dome, 600 TVL, 2.9mm lens, black, with IR
MVC-7100-29-W Mini-dome, 600TVL, 2.9mm lens, white, No IR
MVC-7100-29-WI Mini-dome, 600TVL, 2.9mm lens, white, with IR
MVC-7100-36-BL Mini-dome, 600 TVL, 3.6mm lens, black, No IR
MVC-7100-36-BLI Mini-dome, 600 TVL, 3.6mm lens, black, with IR
MVC-7100-36-W Mini-dome, 600TVL, 3.6mm lens, white, No IR
MVC-7100-36-WI Mini-dome, 600TVL, 3.6mm lens, white, with IR
MVC-7100-60-BL Mini-dome, 600TVL, 6.0mm lens, black, No IR
MVC-7100-60-BLI Mini-dome, 600 TVL, 6.0mm lens, black, with IR
MVC-7100-60-W Mini-dome, 600TVL, 6.0mm lens, white, No IR
MVC-7100-60-WI Mini-dome, 600TVL, 6.0mm lens, white, with IR
MVC-7200-29-BL Mini-dome, 520 TVL, 2.9mm lens, black, with WDR
MVC-7200-29-W Mini-dome, 520 TVL, 2.9mm lens, white, with WDR
MVC-7200-36-BL Mini-dome, 520 TVL, 3.6mm lens, black, with WDR
MVC-7200-36-W Mini-dome, 520 TVL, 3.6mm lens, white, with WDR
MVC-7200-60-BL Mini-dome, 520 TVL, 6.0mm lens, black, with WDR
MVC-7200-60-W Mini-dome, 520 TVL, 6.0mm lens, white, with WDR
Installation
Mounting the Camera
1. Using the provided hex wrench, loosen the set
screw on the side of the camera just enough to
unscrew the lens cover. See Figure 1.
Figure 1 Loosen set screw
2 Mini-Dome Camera Installation Manual
2. Using the camera mounting base as a guide, mark
the center of the mounting base and the position of
the three mounting screws on the mounting surface
as shown in Figure 2.
Figure 2 Mark the mounting holes and center
3. Cut the center hole for the video/power cable
connectors (typically 9/16” or more) as shown in
Figure 3.
Figure 3 Cut the cable hole
4. Drill the three mounting holes as shown in Figure 4
using a bit sized according to the mounting
hardware you will use.
Figure 4 Drill the mounting holes
5. Use a deburring tool to eliminate sharp edges from
the center hole to prevent video cable damage.
6. If using rivnuts, install stainless steel rivnuts as
shown in Figure 5.
Figure 5 Install stainless steel rivnuts
7. If using the flat head sheet metal screws or other
hardware, install hardware to secure camera base to
surface.
NOTE: Application of blue Loctite is recommended on
the camera base mounting screws to prevent
loosening.
Figure 6 Install the camera base
8. Remove the protective covering from the camera,
and remove the dome from the camera plate by
unscrewing counter-clockwise.
9. Feed the camera cable harness through the center
hole, and pull gently until the camera is against the
base.
The cable will be accessed from inside the vehicle
through an appropriate access panel for later
connection to the DVR. When the camera pigtail
BNC is connected to the video cable, wrap the BNC
connector with electrical tape.
10. Use the three machine screws with red nylon
washers to attach the camera to the base. Hand
tighten the screws until snug.
Mini-Dome Camera Installation Manual 3
Figure 7 Remove the cover
Adjusting the lens
Once the camera is mounted, it is adjustable in three
dimensions. The camera module is a ball in a cup.
The ball will rotate in any direction in the cup for view
adjustment: up, down, left, right, clockwise, counter-
clockwise, etc. However, large adjustments can create
internal wire tension. Therefore, we recommend
positioning the camera as close as possible to the
correct orientation during installation so that you do not
need to make adjustments that rotate the ball more than
45 degrees clockwise or counter-clockwise.
1. Connect appropriate power and a video monitor to
the camera, or connect the camera to the DVR, to
view the image and adjust the angle of view and
focus of the lens to ensure the desired image.
2. Two screws, one on each side of the camera,
secure the camera lens cup and also lock the
camera lens ball in place after adjustment. Loosen
these two screws slightly (do not remove the
screws) and rotate the camera as necessary for
final view alignment. Tighten the screws when
finished with the adjustment.
Figure 8 Loosen the two screws just enough to adjust the view
Installing the cover
1. Install the camera cover by tightening in a clockwise
direction.
Figure 9 Replace the cover and tighten the set screw
2. Tighten the set screw in the side of the camera
(shown in Figure 1) to secure the cover in place.
4 Mini-Dome Camera Installation Manual
Troubleshooting
There is no image or it is intermittent.
Check video cable connections. The BNC connector
may be shorted or the wires pinched.
Ensure that the BNC connector inside the connection
box is wrapped with electrical tape to prevent metal-
to-metal contact with the camera housing.
Ensure that the pigtail wires coming from the camera
are not pinched.
Image is upside down or misaligned on the
monitor.
The camera is not properly aligned. Adjust the
camera for the correct view.
FCC Compliance
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
installation instructions, may cause harmful
interference to radio communications.
You are cautioned that any changes or modifications
not expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
Contact information
North America:
855-MOBVIEW (662-8439)
MobileViewTS@fs.utc.com
Latin America:
561-998-6114
latam@interlogix.com
Web site:
www.interlogix.com/mobileview
2013005 March 2013
© 2013 Interlogix, Inc.
www.interlogix.com/mobileview
Mounting bracket template
Use the mounting bracket template to mark the positions of the mounting and cable entry holes on the mounting
surface.
Dieses Handbuch passt für folgende Modelle
17
Inhaltsverzeichnis
Andere Interlogix Sicherheitskamera Handbücher
Interlogix
Interlogix TruVision Open Standards Bedienungsanleitung
Interlogix
Interlogix TVB-5301 Bedienungsanleitung
Interlogix
Interlogix True Vision TVP-5104 Bedienungsanleitung
Interlogix
Interlogix TruVision TVT-2103 Bedienungsanleitung
Interlogix
Interlogix TruVision TVB-6102 Bedienungsanleitung
Interlogix
Interlogix TruVision TVD-6120VE-2 Bedienungsanleitung
Interlogix
Interlogix Ultra View UVD-6120VE-2 Bedienungsanleitung
Interlogix
Interlogix TruVision TVA-1101 Bedienungsanleitung
Interlogix
Interlogix TruVision TVD-7120VE-2 Bedienungsanleitung
Interlogix
Interlogix TruVision HD-TVI 3MPX Merkblatt
Interlogix
Interlogix TruVision TVB 2102 Bedienungsanleitung
Interlogix
Interlogix TruVision TVA-1101 Bedienungsanleitung
Interlogix
Interlogix TruVision TVP-5104 Merkblatt
Interlogix
Interlogix TruVision TVD-2404 Bedienungsanleitung
Interlogix
Interlogix UltraView PTZ Bedienungsanleitung
Interlogix
Interlogix TruVision Series Bedienungsanleitung
Interlogix
Interlogix UVP-M1120P-18X-N Bedienungsanleitung
Interlogix
Interlogix UVD-XP4DNR(-P) Bedienungsanleitung
Interlogix
Interlogix TruVision Line Bedienungsanleitung
Interlogix
Interlogix UltraView IP PTZ 36X Bedienungsanleitung
