Interlogix TruVision TVC-6110-1 Bedienungs- und Wartungsanleitung

TVC-6110-1 / TVC-6120-1 Camera Quick Start

Guide

Introduction

This is the Quick Installation Guide for the TVC-6110-1-N(-P)/

TVC-6120-1-N(-P) camera.

Refer to the user manual for complete instructions on installing

and configuring this camera.

User guidelines

• Program the camera settings as much as possible before

mounting the camera. Take appropriate safety precautions

while completing programming after installation.

• Always use a 12 VDC or 24 VAC UL listed Class 2 power

supply to power the camera.

• Do not use the camera over the temperature range

specifications: -10°C to +50°C (14°F to 122°F)

• If the light source where the camera is installed

experiences rapid, wide- variations in lighting, the camera

may not operate as intended.

WARNING: To reduce the risk of fire or electronic shock, do

not expose the camera to rain or remove cover.

Description

Figure 1: Camera description

TVC-6110-1-N(-P)

1. OSD control button

2. Power LED

3. 12 VDC Power

4. Video output

5. Ground

TVC-6120-1-N(-P)

1. OSD control button

2. Alarm output/Ground

3. D/N switch (3.3V)

4. RS-485 ports (D+, D-)

5. Power LED

6. 12 VDC/24 VAC dual power

7. Video output

8. Ground

Installation

Please check the package contents and make sure that the

device in the package is in good condition and all the assembly

parts are included.

The camera is designed for both indoor and outdoor use. To

use the camera outdoors, it must be installed in an approved

outdoor housing.

Note: Before installing, please ensure that the mounting

surface is strong enough to withstand three times the weight of

the camera. If the wall is not strong enough, the camera may

fall and cause serious damage.

Install the camera

1. Attach the lens.

Refer to the instructions that came with the lens you

purchased for complete installation instructions of that

lens.

Screw the lens clockwise onto the lens mount of the

camera. Take care to prevent dust from entering between

the lens mount and the lens.

For optimal performance, please use an auto iris lens.

Plug the auto-iris drive cable to the 4-pin interface on the

side of the camera. The 4 pins are: 1. Damper -; 2.

Damper+; 3. Drive+; 4. Drive-



2. Connect the cables.

Connect a coaxial cable from the camera’s BNC connector

to a CCTV monitor or video recording device. Connect a

12 VDC or 24 VAC power supply to the power input.

Power supply

Monitor

2 / 2 P/N 1072544B-EN • REV 0.04 • ISS 21JUN12

Programming

Once the camera hardware has been installed, it can then be

configured. Program the camera by attaching a standard video

monitor to the system. Press Enter on the camera’s menu

control button to display the Setup menu (see Figure 2).

OSD control button

The on-screen display (OSD) control button (see Figure 1) is a

five-direction joystick that lets you manually control the camera

functions. Table 1 below lists the OSD control button functions

and describes their use.

Table 1 Description of the OSD control button

Button

direction

Description

Up Moves the cursor upward to select an item

Left Moves the cursor left to select or adjust the

parameters of the selected item.

Right Moves the cursor to the right to select or adjust

the parameters of the selected item.

Down Moves the cursor downward to select an item.

Enter Press the center of the control pad to display the

Setup menu. If the selected item has its own

menu, press the control pad to enter a submenu.

Using the Setup menu

The Setup menu provides access to the camera configuration

options.

Figure 2: Setup menu screens

Table 2: Setup menu description

Menu item Description

Lens Defines the camera ID, mirror, and digital noise

reduction (DNR) set up.

Shutter/AGC Defines the method of iris control.

White Bal Defines the white balance (WB) set up.

Backlight Defines the highlight compensation (HLC) and

backlight compensation (BLC) set up.

Pict Adjust Defines the image quality functions.

ATR Defines the wide dynamic range (WDR) set up.

Motion Det Defines the motion detection set up.

Privacy Defines privacy mask set up.

Day/Night Defines the day/night (D/N) set up.

NR Defines the digital noise reduction level.

Camera ID Defines the camera ID displayed on-screen.

Sync Displays the current synchronization mode.

Language Defines the language of the OSD.

Camera Reset Resets the camera to factory default settings.

Menu item Description

Save All Saves configuration changes made.

Exit Exits the menu and returns to live mode.

To access the Setup menu:

1. Press the OSD control button to access the Setup menu

and its submenus.

2. Push the button up/down to move between menu options.

3. Push the button left/right to select an option.

4. Select Next to move to the next Setup menu screen and

Back to return to the previous Setup menu screen.

5. When in a sub menu, select Return to return to the

previous menu.

6. To save configuration changes, select Save All and press

Enter.

7. To exit the Setup menu and return to normal camera

operation mode, move the cursor to Exit at the bottom of

the screen and press Enter.

Menu map

Dieses Handbuch passt für folgende Modelle

Andere Interlogix Sicherheitskamera Handbücher

Interlogix

Interlogix TruVision TVB-2101 Bedienungsanleitung

Interlogix

Interlogix TruVision TVB-2401 Bedienungsanleitung

Interlogix

Interlogix Ultra View UVD-6120VE-2 Bedienungsanleitung

Interlogix

Interlogix 36X Bedienungsanleitung

Interlogix

Interlogix TruVision TVD-N210V-2-N(-P) Bedienungsanleitung

Interlogix

Interlogix TruVision TVD-7120VE-2 Bedienungsanleitung

Interlogix

Interlogix TruVision Series Bedienungsanleitung

Interlogix

Interlogix TruVision TVT-2101 Bedienungsanleitung

Interlogix

Interlogix UVP-N120P-36X(-P) Bedienungsanleitung

Interlogix

Interlogix TVC-5120-1 Bedienungsanleitung

Interlogix

Interlogix TruVision TVD-5801 Bedienungsanleitung

Interlogix

Interlogix MobileView MVC-7100-29-BL Bedienungsanleitung

Interlogix

Interlogix UltraView UVD-6130VE-2-P Bedienungsanleitung

Interlogix

Interlogix TruVision TVP-5101 Merkblatt

Interlogix

Interlogix UltraView PTZ Bedienungsanleitung

Interlogix

Interlogix TruVision TVB-2402 Bedienungsanleitung

Interlogix

Interlogix UltraView IP PTZ 36X Bedienungsanleitung

Interlogix

Interlogix TruVision TVT-2103 Bedienungsanleitung

Interlogix

Interlogix TruVision Line Bedienungsanleitung

Interlogix

Interlogix TruVision TVB-2402 Bedienungs- und Wartungsanleitung

Interlogix

Interlogix TruVision Open Standards Bedienungsanleitung

Interlogix

Interlogix UVC-XP4DN-HR Bedienungsanleitung

Interlogix

Interlogix TruVision TVP-5104 Merkblatt

Interlogix

Interlogix FW5.1 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung