Kohler K-7303 Bedienungsanleitung

Installation Guide

Widespread Lavatory Faucets

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-7303 K-7313

117121-2-AB

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Carefully inspect the waste and supply tubing for any sign of

damage.

Replace waste or supply tubing if necessary.

For new installations, install the faucet before installing the

lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Adjustable

Wrench Hacksaw or

Tube Cutter Pipe Wrench

ScrewdriverThread

Sealant

Plumbers

Putty

117121-2-AB 2 Kohler Co.

1. Spout Installation

Apply a bead of plumbers putty or other sealant to the underside

of the spout or putty ring (if supplied) according to the putty

manufacturer’s instructions.

Locate the center hole and insert the spout.

Slide the metal washer and nut onto the spout shank.

Position the metal washer so the second hole is at the back of the

spout.

Securely tighten the nut with a wrench. Do not overtighten.

Remove any excess putty or sealant.

Apply

Plumbers

Putty

Metal

Washer

Spout

Nut

Kohler Co. 3 117121-2-AB

2. Rigid Supply Tee Installation

Insert the plastic gasket and the rubber washer into the top of the

supply sleeve.

Slide the metal washer onto the spout shank.

Thread the shank nut up onto the spout approximately 1″(2.5

cm).

Thread the supply tee to the spout shank until it is hand tight.

Tighten the hex-end of the supply tee with a wrench. Ensure that

the tubes are aligned to the sides. Do not overtighten.

Slide the metal washer down the shank to the rigid supply sleeve.

Thread the shank nut down to the washer. Securely tighten with

a wrench. Do not overtighten.

Spout

Shank

Nut

Plastic

Gasket

Tee Supply

Sleeve

Rubber

Washer

Tee Supply

Hex-End

Washer

117121-2-AB 4 Kohler Co.

3. Handle Valve Installation

Thread a locknut onto each valve body. The ﬂat surface of the

locknut should face up towards the lavatory.

Slide a ﬁber washer onto each locknut.

NOTE: The valve body marked ″Cold″(with blue lettered tape

attached to the tube) should be installed to the right of the faucet.

Apply a bead of plumbers putty or other sealant to the underside

of the escutcheons according to the putty manufacturer’s

instructions.

From the underside of the lavatory, insert the ″Cold″and ″Hot″

valve bodies into the mounting holes.

From the top of the lavatory, thread an escutcheon onto each

valve until hand tight.

Slide a compression nut and ferrule onto each supply tee inlet

tube.

Align the end bodies so the supply tubes ﬁt evenly into the valve

body outlets.

Tighten the compression nuts from the supply tubes to the valve

body outlets.

While holding the valve bodies in place, securely tighten the

locknuts with a wrench. Do not overtighten.

Remove any excess putty or sealant.

Apply

Plumbers

Putty

Fiber

Washer

Escutcheon

Locknut

Valve Body Valve Body

Outlet

Compression

Nut

Supply Inlet

Tube

Ferrule

Kohler Co. 5 117121-2-AB

Handle Valve Installation (cont.)

Install the handles according to manufacturer’s instructions.

117121-2-AB 6 Kohler Co.

4. Supply Connections

Install the lavatory using the lavatory manufacturer’s instructions.

Connect the supply tubes to the handle valves, and the supply

stops. Left is hot and right is cold.

Tighten all connections.

Compression

Union

Hot Cold

Kohler Co. 7 117121-2-AB

5. Installation Checkout

Connect the tailpiece and P-trap (as needed).

Install strainer bodies (as needed).

Ensure that all connections are tight.

Remove the aerator by turning it counterclockwise.

Open the drain.

Turn on the main water supply and check for leaks. Repair as

needed.

Open both hot and cold valves and run water through the spout

for about a minute to remove debris. Check for leaks. Turn valves

off.

Remove any debris from the aerator and reinstall.

Aerator

117121-2-AB 8 Kohler Co.

Guide d’Installation

Robinets de Lavabo à Entraxe Large

Outils et Matériels

Merci d’Avoir Choisi la Société Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît, quelques minutes et lire attentivement ce

manuel avant de commencer l’installation. Ne pas hésiter à nous

contacter en cas de problème d’installation ou de fonctionnement. Nos

numéros de téléphone et notre adresse du site internet sont au verso.

Merci encore d’avoir choisi la Compagnie Kohler.

Avant de Commencer

Respecter tous les codes de plomberie et de bâtiment locaux.

Couper l’arrivée d’eau principale.

Vériﬁer avec soin si les tubes d’évacuation ou d’arrivée d’eau

sont endommagés.

Replacer les tubes d’alimentation ou d’évacuation si nécessaire.

Pour les nouvelles poses, installer le robinet avant d’installer le

lavabo.

La Société Kohler se réserve le droit d’apporter toutes

modiﬁcations sur le design des robinets et ceci sans préavis,

comme spéciﬁé dans le Catalogue des Prix.

Clé à molette Scie à métaux ou

coupe tube Clé à tubes

TournevisRuban d'étanchéité

pour filets

Mastic

d'étanchéité

Kohler Co. Français-1 117121-2-AB

1. Installation du bec

Appliquer du mastic d’étanchéité ou un produit semblable sur le

dessous de bec ou de l’anneau de mastic (si fourni) selon les

instructions du fabricant du mastic.

Localiser l’oriﬁce central et insérer le bec.

Glisser la rondelle métallique et l’écrou sur la tige du bec.

Placer la rondelle métallique de manière à ce que le deuxième

trou soit à l’arrière du bec.

Serrer fermement l’écrou à l’aide d’une clé à tuyaux. Ne pas trop

serrer.

Enlever tout excédent de mastic d’étanchéité.

Appliquer

du mastic

d'étanchéité

Rondelle

métallique

Bec

Écrou

117121-2-AB Français-2 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler STANCE Bedienungsanleitung

Kohler

Kohler K-11496X Montageanleitung

Kohler

Kohler K-7744 Bedienungsanleitung

Kohler

Kohler Stance 10317T-4 Bedienungsanleitung

Kohler

Kohler K-251 Bedienungsanleitung

Kohler

Kohler K-2277 Bedienungsanleitung

Kohler

Kohler Mira Evoco Series Bedienungsanleitung

Kohler

Kohler Portrait K-2272 Bedienungsanleitung

Kohler

Kohler K-2282 Bedienungsanleitung

Kohler

Kohler MODULO 72801T-4 Bedienungsanleitung

Kohler

Kohler Sterling SC2522SBG Montageanleitung

Kohler

Kohler K-8807 Bedienungsanleitung

Kohler

Kohler K-72218 Bedienungsanleitung

Kohler

Kohler K-4108BR Bedienungsanleitung

Kohler

Kohler K-4709 Bedienungsanleitung

Kohler

Kohler STERLING 996 Bedienungsanleitung

Kohler

Kohler ENGLEFIELD TAPWARE STUDIO 20149A-4 Bedienungsanleitung

Kohler

Kohler K-2268 Bedienungsanleitung

Kohler

Kohler K-T15601 Bedienungsanleitung

Kohler

Kohler Portrait K-2226 Bedienungsanleitung

Kohler

Kohler Sterling 225C7 Montageanleitung

Kohler

Kohler 1283722 Bedienungsanleitung

Kohler

Kohler K-6132 Montageanleitung

Kohler

Kohler 13EOZD Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung