Kohler LOURE 98452T-CP Bedienungsanleitung

All information is based on the latest product information

available at the time of publication, Kohler Co. reserves

the right to make changes in product characteristics,

packaging, or availability at any time without notice.

Please leave these instructions for the consumer. They

contain important information.

所有的资料是按最新出版的产品资料编写而成。

科勒公司保留任何时候不经通知即可改变产品特

性、包装或产品可供类型的权利。

说明书包括重要的安装、保养及清洁方面的内容，

请把这些资料交给用户阅读。

1. Flush the water supply pipes thoroughly to remove debris.

Faucet is designed for tap water or potable water.

2. Do not apply excessive force to the product as doing so

may cause damage.

3. Do not damage the surface of sensing window when

installing or cleaning the faucet.

4. When installing DC type faucets, pay special attention

to the directions of battery electrodes. Tighten the battery

cover to prevent its exposure to moisture.

5. When installing AC type faucets, strictly follow indicated

instructions to perform electric connection. Do not turn on

AC power supply before installation is completed.

6. One AC power supply can power no more than two

faucets at a time.

7. General power supply must be protected by proper fuse.

8. Do not put the faucet near strong ultraviolet or

electromagnetic ﬁeld.

9. Cover the sensing window with black tape when

repairing lavatory.

1. 一定要先彻底冲洗供水管以清除管道中的杂

质,使用水源为自来水或可供饮用水。

2．请勿将强力及冲击施于产品，以免造成故障，

引起漏水。

3．安装、清洁龙头时，切勿损伤感应窗口表面，

以免造成故障。

4. 对于直流龙头，安装时注意电池的正负极不

能装反，电池盒盖要拧紧，防止电池受潮。

5. 对于交流龙头，安装时务必按照说明书的要

求正确连接导线，龙头安装完毕后才可向电源盒

供电。

6. 一个交流电源盒最多可供两个感应龙头。

7. 交流电的总电源必须有合适熔断丝加以保护。

8. 请勿使产品感应窗口靠近强紫外线或电磁场。

9. 修理面盆时，用黑色电工胶布粘住感应窗口。

10.维修交流龙头时，必须断开交流电源并关闭

水源。

萝瑞入墙式单冷交流感应龙头(不带交流电源盒)

萝瑞入墙式单冷直流感应龙头

98452T-CP

98453T-CP

10.Turn off AC power supply and water supply before repairing

faucet.

安装之前

NOTES:

上海科勒电子科技有限公司

中国上海浦东新区金滇路18号E幢邮编：201206

BEFORE YOU BEGIN

注意事项

安装说明书

萝瑞

LOURE

Wallmount Sensor Faucet

1205259-2-A

建议搭配脸盆 RECOMMENDED LAVATORIES

K-2215T-M 拉蒂纳台下脸盆

K-2210T-0 卡斯登台下脸盆

K-2889T 维克长方形台下脸盆

K-2768T-1 皓玥台下盆

K-2660T-1 拂朗长方形时尚脸盆

K-2211T 卡斯登台下脸盆

K-2339T 梅玛台下脸盆

K-2661T 拂朗正方形时尚脸盆

K-14800T 乔司时尚脸盆

K-2215T-M Ladena®Under Counter Lavatory

K-2210T-0 Caxton ®17" Under Counter Lavatory

K-2889T Verticyl ®Rectangular Lavatory

K-2768T-1 Karess Under Counter Lavatory

K-2660T-1 Forefront™ Vessel

K-2211T Caxton ®Under Counter Lavatory

K-2339T Memoirs ®Under Counter Lavatory

K-2661T Forefront™ Vessel

K-14800T Chalice™ Vessel

注意：如果使用非推荐的脸盆，可能会产

生溅水在脸盆外面等情况。

NOTE: To prevent water from splashing out, users are

recommended to use lavatories as recommended above.

使用说明 OPERATION INSTRUCTIONS

Once user's hands enter the sensing range, the

faucet automatically activates water ﬂow. Water

ﬂows until 0.5~1 seconds after the hands are

removed or until the faucet reaches its 1-minute

timeout setting. The faucet adjusts its sensing

distance automatically as per the condition of

the lavatory and surrounding environment.

手伸到出水口下方感应范围内

（感应距离随面盆、周围的情况

而自动调节），水龙头出水。手

离开后0.5～1秒，水龙头自动止

水。

2 1205259-2-A

技术参数

电源：直流 2节5号碱性电池(LR06 ×2)

交流电压220V,频率50/60Hz

检测时间：小于0.5秒

关阀延时：0.5～1秒

感应距离：自动调节

流量：水压为0.3MPa 时，流量不大于 2.0L/s

超时用水控制：超时用水1分钟，自动止水。

环境温度：1～55

进水温度：0.5～71

适用水压：0.05～

0.86MPa

PARAMETERS

Power: DC 2 AA alkaline batteries

AC 220V, 50/60Hz

Sensing Duration: Less than 0.5s

Shut-off Delay: 0.5~1s

Sensing Distance: Adjusts automatically

Flow Rate: No more than 2.0L/s at 0.3MPa.

Timeout Setting: 1 minute

OperationTemperature: 1~55℃

Water Temperature: 0.5~71℃

Water Pressure: 0.05~0.86MPa

℃

排水组件

41.2

31.75

226

66.5

交流电源盒

Output: DC3V

输出:

直流电压3V

Input:AC220V

输入:

交流电压220V

安装尺寸 ROUGH-IN

注意:台盆里侧边缘与产品安装墙面的

距离不超过10cm，否则可能影响美观

以及手在使用时的舒适性。

NOTE: To ensure beauty and comfort, the distance

between the wall and the lavatory shall not exceed

10cm.

98453T-CP

萝瑞入墙式单冷直流感应龙头

98452T-CP

萝瑞入墙式单冷交流感应龙头

台盆顶面

150

90~115

完整墙面 58

450

340

用户自备 32

穿线管

207

用户自备角阀

G1/2外螺纹

用户自备角阀

G1/2外螺纹

台盆顶面

200

150

90~115

完整墙面 58

207

450

340

用户自备 32

穿线管

Max 10cm

1205259-2-A

将安装组件放入槽内，并用自攻

螺钉固定。

保证安装组件的底部与完工墙面的距

离在70～105mm之间，如图（Ⅰ）。

保证暗装架组件的底部与墙面平行，

不能歪斜，如图（Ⅱ）。

一安装暗装架组件

根据台盆大小确定安装方式，确保

龙头出水中心正对台盆中心位置。

1. 凿挖安装槽坑

根据安装尺寸图确定安装位置，凿

出槽坑，埋设供水管，暂不供水。

槽深70～105mm，尺寸如图。安

装位置应避免光源直射或反射进入

感应窗口，不能在感应器正对面有

易反射的物品（如镜子、光亮不锈

钢件及其他镜面物体等）；不能靠

近强烈紫外线或电磁场。

在安装尺寸位置钻孔，打入膨胀管。

2. 固定安装组件

1. Install Mounting Bracket Assy.

INSTALLATION

Determine installation method per

lavatory size, and make sure the center

of faucet outlet aligns with the center of

the lavatory.

1. Chisel out a Slot

Determine the installation lacation per

rough-in. Chisel out a slot with a depth

of 70~105mm and lay water supply

hoses. Turn off the water supply

temporarily. The dimensions are shown

in the figure. The installation area shall

be located at a place where no direct

light is allowed to enter or reflected into

the sensing window, where no objects

susceptible to reflection are placed in

front of the sensor (e.g., mirror, polished

stainless steel and other objects with

mirrored surface); where no strong

ultraviolet radiation or electromagnetia

field is found nearby.

Drew mounting hole and put in

expansion pipe.

2. Secure Mounting Bracket Assy.

Insert the mounting bracket assy. to the

slot and secure it with self-tapping

screws.

Ensure that the distance between the

bottom of the mounting bracket and the

wall ranges between 70~105mm as

shown in Fig. (I).

Ensure that the bottom of the mounting

bracket assy. is parallel with the wall as

shown in Fig. (II).

150

完工墙面

70~105

二安装龙头

1. 拧下自攻螺钉(1),拔出灰浆

模套(2)。

2. 将龙头的进水软管和线束穿入

安装支架，由出线管穿出，将龙

头穿入安装组件上的螺钉，旋转

一定的角度，拧紧螺钉，尽量调

整龙头的出水方向对准脸盆。

3. 将装饰盖(3)由龙头的出水口穿

入，使用螺钉(4)固定。

2. Install Faucet

1. Remove the self-tapping screws (1)

and slide the slurry mold (2) off the

body.

2. Make faucet water pipe and wire

through mounting bracket, screw and

secure spout to the mounting bracket,

make sure the spout forwarding to

vessel.

3. Insert the escutcheon (3) into the

spout and secure it with screw (4).

用灰浆填埋槽道，在瓷砖上打好孔

张贴瓷砖后的墙面如图。

Fill slurry into the slot and drill holes

on tiles as shown in the figure.

1205259-2-A

将角阀(9)与管道出水口连接，再

将软管(10)与角阀(9)连接，在软

管(10)前放一水桶，将角阀(9)完

全打开，打开供水系统，通水约一

分钟，确认管道连接触无渗漏后，

关闭供水系统。 10

Connect check valve (9) and outlet

together, then connect the hose (10) and

check valve (9). Put a bucket in the front

of hose (10), turn on the check valve (9)

completely and open the water supply.

After the water flushing about 1 minute,

make sure no leakage and turn off the

water supply.

用螺丝刀拧下阀盒盖螺钉(7)，将

阀盒盖(6)打开。根据安装尺寸图

确定控制阀组件(5)安装位置，打

孔，打入膨胀管，使阀盒紧贴墙

面且控制阀组件出水口朝上，再

用膨胀螺钉(8)将控制阀组件固定

在墙壁上，注意控制阀组件要与

墙面保持平行。

控制阀组件的安装固定 4. Fix the control box

Remove the cover (6) after loose the

screws (7). Determine the installation

location of control box (5) per rough-in,

then drill holes and place sheath in it.

Make the control box cling on the wall

and outlet upturned, then fix the control

box on the wall by screws (8), keep the

control box parallel to the wall.

再将软管(10)与阀体进水口连接，

然后连接阀体出水口与龙头组件

出水软管(11)。

注意：

1. 出水软管处的平垫不要遗漏。

3.请勿将进水口与出水混淆。

取出电池盒组件，拧开螺钉(12)，

按电池盒盖(13)上的正负极标示分

别装入2节5号电池(14)，锁紧电池

盒盖(13)的螺钉(12)后，将电池盒

组件放入阀盒的专用槽内。

注意:

电池正负极不能装反，新旧电池不

能混用。

出水口

Outlet

进水口

Inlet

圆孔

Round Hole

六角形孔

Hex Hole

Take out the battery box and loose the

screws (12), place two “AA” batteries into

the box according to the negative and

positive pole mark on the cover of battery

box (13). Put the box in the particular

groove in the valve box after tight the

screws.

Note:

Do not mistake the pole and mixture the

new and used batteries.

1205259-2-A

请用户自备角阀。

Connect hose (10) to the inlet of valve,

then connect the outlet of valve and

inlet (11) of spout assy.

Note:

3. Do not confuse the inlet and outlet.

by themselves.

Do not lost the washer of hose.

Please let user prepare check valve

11 Finally, connect the red-green lines in

solenoid valve and cover of valve box,

then connect the black-orange lines in

power supply and control board ( If you

faucet is AC version, please let the

black-green line in the control board

through the “U” gap and connect with the

line of AC power box). Connect the red

and white connectors in the sensor line

and cover, and tight the box(5) and

cover(6) by screws(7)

Note:

1. When install the box and cover by

screws, make sure the sensor line need

to be through “U”Gap of cover.

2. Connect the batteries,faucet will be in

the period of automatic adjusting sensing

distance (about 2minutes).The faucet

will not work during this period.

最后，将电磁阀上的红绿线与对应阀

盒盖组件上的红绿线接插，将电池盒

或交流电源盒上黑橙线与主控板组

件上黑橙线接插，（交流版请将主

控板组件上的黑橙线从小U型缺口

引出与交流电源盒上的黑橙线连接）

再将探头线的红、白接插件分别与

阀盒盖上对应的红、白接插件连接，

再用阀盒盖螺钉(7)拧紧阀盒(5)

和阀盖(6)。

注意:

1. 在用螺钉固定阀盒(5)和阀盖(6)

时，确保探头线(17)需通过阀盖上

大U型缺口。

2. 接上电池后，龙头进入2分钟自动

调距阶段，此过程龙头不会出水。

接交流电源盒

Connect AC/DC

transformer

如何安装排水组件 How to Install the Drain

旋下排水器盘片(18)，在其底面沿

周围涂上一圈密封油灰。把排水本

体(19)由底下插入面盆。

Screw off the drain flange (18) from drain.

Apply a ring of plumbers putty around

underside of the drain flange(18). Insert

the drain body(19) into the lavatory from

the underside.

Apply plumbers putty

涂油灰

Thread the drain flange (18) onto the drain

Body (19). Tighten the locknut (20) by hand

from the underside of the fixture. Remove

any excess putty.

把尾管(21)接上存水弯(22)，尾管

需插入存水弯25mm到55mm之间。

Connect the tailpiece(21) to the trap(22).

The tailpiece should extend 25mm to

55mm into the trap.

Note: Do not try to change the position of

the drain after the locknut(20) is tightened,

or you may break the putty seal.

把排水器盘片(18)旋入排水本体

(19)。从下方用手拧紧锁紧螺母

(20)，去除多余的油灰。

注意：在锁紧螺母(20)拧紧后，不

可再调整排水本体的位置，否则将

会破坏油灰密封。

1205259-2-A

如何安装交流电源盒

(若用户另购

交流电源盒,

具体安装详见其说明书

)

HOW TO INSTALL THE AC/DC

TRANSFORMER (ONLY USED

WITH TOUCHLESS FAUCET,AC)

AC/DC transformer

交流电源盒

一个交流电源盒供一个感应龙头

接220V交流电

Connect AC 220V

Switch

开关

Wire Tube

穿线管

Wire connection pattern for one to one Faucet

感应龙头

Wire connection pattern for one to two

一个交流电源盒供两个感应龙头

Connect to

electrical Source

接交流电源

注意：禁止将交流AC220V接入直流DC接线端。

Connect to

Faucet

接感应龙头 Connect to

electrical Source

接交流电源 Connect to

Faucet

接感应龙头

Note: Not allowed connect AC 220V electrical source to DC wire connector of AC/DC transformer

Faucet

感应龙头

Wire Tube

穿线管

Switch

开关

Wire

连接线 Wire Tube

穿线管

AC/DC

transformer

交流电源盒

Faucet

感应龙头

接220V交流电

Connect AC 220V

外螺纹

1205259-2-A

用户自备角阀

G1/2外螺纹

Please user prepare

external thread check

valve G1/2

用户自备角阀

G1/2

Please user prepare

external thread check

valve G1/2

1. InstallAC power unit (sticker on the back) dry, andavoid

showering, soaking from water. Customer prepare wire

tube and wire according to requirement. Wire tube

should be put into the wall. Suggested wire:AC connection

wire should with insulated protecting layer or sleeve and

the section should be bigger than 0.5mm . The section of

DC connectionwire should be

bigger than 0.3mm . The

connection pattern must according to illustrations above.

2. After wire layout finished, check and repair if needed.

Then connect AC connector of AC/DC transformer to

electrical source from the control box, and DC connector of

AC/DC transformer to faucet. Turn on AC electrical power,

faucet will be in the period of automatic adjustingsensing

distance (about 2 minutes).The faucet will not work during

thisperiod.

直流连接线采用导体标称截面积 mm 的电线。

请严格按照上图进行连接。

0.3

1.电源盒 (背面有不干胶)应安装在干燥，不会被水

淋湿、浸泡的位置。根据需要客户自备穿线管及

连接线。穿线管安装在墙内。建议交流电源线采用

带绝缘和护套层的电线，导体标称截面积 0.5mm ;

2. 排线完毕后，应检查并确保所有排、接线无误，

再分别连接电源盒AC接线端与排线管内交流接线

端，以及电源盒DC接线端(黑橙线接头)与龙头的

电源线接插件（从阀盒内引出的电线），最后打

开AC电源，龙头进入2分钟自动调距阶段，此

过程龙头不会出水。

如何超能动电池系统

(若用户另购

超能动电池,

具体安装详见其说明书)

Hybrid Energy System

超能动电池系统

Faucet

感应龙头

HOW TO INSTALL THE Hybrid

Energy System

(If using hybrid energy

system as power supply, please refer to

its installation instruction)

台盆顶面

Vessel rim

1205259-2-A

用户自备角阀

G1/2外螺纹

Please user prepare

external thread

check valve G1/2

thermostatic valve

注：三通、角阀请用户自备。 Note: Please let users prepare the tee and check valve by

themselves.

接感应龙头

Connect Sensor Faucet

单向阀滤网组件

Check valve

strainer assy.

单向阀滤网组件

Check valve

strainer assy.

用户自备角阀G1/2外螺纹

Please user prepare external

thread check valve G1/2

用户自备角阀G1/2外螺纹

Please user prepare external

thread check valve G1/2

MIN 50mm

10 1205259-2-A

墙面

Wall

墙面

Wall

三通

Tee

进热水

hot

出水口

Outlet

三通

Tee

进冷水

cold

恒温阀

用户自备角阀

G1/2外螺纹

Please user prepare

external thread check

valve G1/2

用户自备角阀G1/2外螺纹

Please user prepare external thread check

valve G1/2

三通软管组件

Tee hose assy

如何转换成混水感应龙头

(若用户另购三通软管组件

1240574-SP)

如何转换成恒温阀感应龙头

(若用户另购

恒温阀16294T-3-CP,

具体安装详见其说明书

)

HOW TO CHANGE TO THERMOSTATIC

SENSOR FAUCET (If users buy the

thermostatic valve 16294T-3-CP, the

installation refer to the manual of

16294T-3-CP)

HOW TO CHANGE TO MIXING SENSOR

FAUCE (If users buy the tee hose assy

1240574-SP)

Andere Handbücher für LOURE 98452T-CP

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Fairfax K-12265 Montageanleitung

Kohler

Kohler STRAYT 37327M Bedienungsanleitung

Kohler

Kohler K-704212 Montageanleitung

Kohler

Kohler K-1491 Bedienungsanleitung

Kohler

Kohler K-7223 Bedienungsanleitung

Kohler

Kohler Thermostatic Electric Shower Bedienungsanleitung

Kohler

Kohler K-3597 Montageanleitung

Kohler

Kohler 99859T Bedienungsanleitung

Kohler

Kohler K-10272 Montageanleitung

Kohler

Kohler CUFF 37305M-4 Bedienungsanleitung

Kohler

Kohler K-10441 Bedienungsanleitung

Kohler

Kohler 22572T-9 Bedienungsanleitung

Kohler

Kohler K-77681 Series Bedienungsanleitung

Kohler

Kohler Mira Sport Bedienungsanleitung

Kohler

Kohler 10-Jet K-1000-H2 Bedienungsanleitung

Kohler

Kohler K-7827 Montageanleitung

Kohler

Kohler K-2600 Bedienungsanleitung

Kohler

Kohler NEW MEMOIRS K-76555T Bedienungsanleitung

Kohler

Kohler 22327T-7 Bedienungsanleitung

Kohler

Kohler K-8872T-2W Series Bedienungsanleitung

Kohler

Kohler SKYLINE Series Bedienungsanleitung

Kohler

Kohler Kumin K-104K36-SANA-CP Bedienungsanleitung

Kohler

Kohler K-812-H2 Montageanleitung

Kohler

Kohler K-T13140 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung